758154
9
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
9
English
8. Use
8.1 Mounting the saw chain
(See Fig. C, D, E).
Always wear gloves when handling the
saw chain.
a. Unscrew the head screw (3) coun-
ter-clockwise in order to remove the
sprocket cover (2).
b. Run the saw chain over the sprocket.
Please note the running direction of the
saw chain. The saw chain icon is shown
on the cover.
c. Use an oiler to oil the saw chain and the
sprocket.
d. Slightly tighten the saw chain with the
chain adjusting screw (7). For tighten-
ing, turn the screw clockwise.
e. Re-tighten the sprocket cover (2) with
the head screw (3) on the housing.
f. Firmly tighten the saw chain with the
chain adjusting screw (7). Use the
included adjustment key (11) to tighten
the screw.
8.2 Chain lubricating oil
Only use commercially available, biode-
gradable chain oils that are specially
designed for use in multi saws.
Do not use engine oil, waste oil or other
mineral oils.
8.3 Adjusting saw chain tension
(See Fig. C).
CAUTION: Do not tighten the saw chain too
much. Excessively high tension of saw
chain may cause breakage of saw chain,
wear of the guide bar and breakage of the
sprocket.
CAUTION: A chain which is too loose can
jump off the guide bar.
The saw chain may become loose after
many hours of use. From time to time check
the saw chain tension before use.
a. Remove the battery.
b. Loosen the head screw (3) a bit to
loosen the sprocket cover lightly.
c. Adjust the chain tension. Turn the chain
head screw (7) clockwise to tighten,
turn it counter-clockwise to loosen.
Tighten the saw chain so that the gap
between the centre of the lower side of
the guide bar and the saw chain
becomes approximately 3 – 4 mm.
d. Tighten the head screw (3) to secure
the sprocket cover.
8.4 Switching ON and OFF
The use of the Nexxsaw without lubricating
the chain with chain oil will damage the saw
chain and the guide bar.
a. Insert the battery into the battery
recess.
b. 
by the handgrip. To switch on the Nexx-
(1)
and release the switch.
c. Then press the ON/OFF switch within 1
second (10).
d. To switch off the saw, release the ON/
OFF switch.
8.5 Break-in time for new saw chains
a. Remove the battery and adjust the
chain tension.
b. Switch on the Nexxsaw and leave the
motor running idle for approx. 5
minutes.
c. Remove the battery and check the
chain tension again. If necessary,
re-tighten the chain.
d. Afterwards make only easy cuts for
approx. 30 minutes. Always ensure

Only use the Nexxsaw for heavier cuts
and greater cutting depths after the
running-in period has expired.
Use only sharp saw chains. Blunt saw
chains can jam more easily. Check the
chain tension more frequently when
working with new saw chains, as the

The service life of a saw chain depends

tension.
During operation, the chain heats up and
re-tensioning may be necessary. Relax
the chain after work so that it is not too
tight the next time the cold machine is
used.
Do not re-tighten saw chains that have
become too hot. After it has cooled
down, it may contract and lie too tight
7063578-Nexxsaw-Ma-WoF-1910-08.indb 9 15-10-19 17:12
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-NXS001 - 7063578 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-NXS001 - 7063578 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 4,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info