758289
11
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
9
English
16.2 Secure the parallel stop by tightening
the fastening screws (11) in the desired
position.
When not using the parallel stop, tighten
the fastening screws (11) securely. The
screws can be unscrewed and fall off
due to the vibration of sawing.
17. Laser
17.1 Safety instructions for the laser cut-
ting guide
a. Do not point the laser beam at persons
or animals and do not look into the
laser beam. This laser emits a laser
beam that falls under laser class 2 in
accordance with EN 60825-1:2014. You
could blind people with it.
b. A laser is not a toy and does not
belong in the hands of children. Using
it incorrectly may result in irreparable
damage to the eyes.
c. It is forbidden to manipulate the laser
so as to increase its power in any way.
No liability will be assumed for any
damages caused as the result of fail-
ure to comply with these safety
instructions.
d. The laser does not contain any ser-
viceable parts. Therefore, do not open
the housing. Otherwise, you will ren-
der the warranty void.
e. Warning! Do not swap the laser with
another type of laser. Only the manu-
facturer of the laser or an authorised
representative may perform repairs.
f. Do not point the laser beam towards
highly reflective surfaces.
g. Do not insert any hard objects in the
laser optics.
h. Clean the laser optics with a soft, dry
cloth.
18. Using the laser
The beam line of the laser is available to
assist in making straight cuts. You can
either cut along the projected line or point
the laser beam at a xed point on the work
piece and then cut.
18.1 To switch the laser on, push the On/Off
switch (13) for the laser.
18.2 To switch the laser off, push the On/Off
switch (13) for the laser again.
19. Tips for cutting
Clamp the workpiece. Use a clamping
device for small workpieces.
Draw a line to dene the direction in
which to guide the saw blade.
Firmly hold the machine by the grip.
Set the sawing speed.
Set the mitre angle.
Set the pendulum position.
Switch on the machine.
Wait until the machine has reached full
speed.
Place the saw shoe on the workpiece.
Slowly move the machine along the
pre-drawn line, rmly pressing the saw
shoe against the workpiece.
Do not apply too much pressure on the
machine. Let the machine do the work.
Switch off the machine and wait for the
machine to come to a complete stand-
still before putting the machine down.
20. Cleaning and maintenance
To avoid injury always pull the power
plug before maintaining or cleaning the
machine.
Clean the machine with a moist cloth.
If the machine is very dirty use a mild
detergent or soap on the cloth. Other
cleaning agents may contain chemical
substances which may damage the
plastic parts of the machine.
Do not allow liquids to enter the
machine and do not immerse the
machine in liquids of any kind.
Repairs, inspections of the interior of
the machine, adjustments and replace-
ment of the carbon brushes may only
be undertaken by a professional. Only
identical replacement parts may be
used! For further information please
contact our customer service
department.
Always keep the ventilation slots (5)
open and clean. After each use remove
dirt and contaminations with a brush or
blow it out with compressed air.
7062849-Jig_Saw_800W-Ma-1803-09.indb 9 22-03-18 11:07
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-JS002 - 7063410 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-JS002 - 7063410 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 4,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info