630470
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
The procedure for changing gears is as follows:
Changing gear: continue to pedal but not too hard and move the gear shifter (lever or rotating handle) until the chain is positioned
on the selected chain ring or cog.
Each lever position corresponds to a dierent cog.
• If the chain has a tendency to slip o the cog: you can try "overshifting" by gently pushing the lever slightly beyond current
position without moving to the next position.
=> If this still doesn't work: you will need to adjust the cable tension.
• If the chain does not move down easily, refer to chapter on "adjusting the gear system." The chain should move smoothly
between cogs.
Warning:
To ensure that the gear system function scorrectly and to
extend service life of drive train parts (chain, free wheel,
pedals):
Avoid sudden, aggressive gear changes.
Avoid crossing the chain (using large cog and large chain
ring or small cog and small chain ring).
If the chain is crossed (diagram 2) it may be in contact
with the front derailleur.
Warning: To ensure optimal use of the manual or automatic gear
change system, you are advised to avoid changing gears during
periods of intense pedaling and to shift to a lower gear before
stopping so it's easier to start o again.
O. Adjusting brakesand recommendations for replacing friction
brake components
The brake lever must not come into contact with the handlebar.
Avoid creating short, sharp bends in the outer casing to ensure the cables can run smoothly.
Damaged, frayed or rusty cables must be replaced immediately.
The brake pads must be aligned with the edge of the rim (at a distance of 1-3 mm). They must never touch the wheels.
Disc brakes must be checked regularly; check all the brake screws and check brake pads for signs of wear; the minimum thickness
should be 1 mm.
Brakes must be adjusted as outlined in section "Preparing for use." You are advised to get a qualied mechanic to carry out these
adjustments.
When replacing brake parts, to ensure the continued performance of your bike, you are advised to use genuine spare parts. This
procedure must be carried out by a qualied mechanic.
P. General maintenance recommendations
Your bike needs a minimum amount of maintenance and regular check-ups, depending on how much you use it: regularly oil
the chain, brush cogs and chain rings, occasionally apply a couple of drops of oil to the outer casing of the brake cables and the
derailleur, and remove any dust from brake pads.
Regularly check the tyres for excess wear, cuts, slashes or toe wear and replace the tyre if necessary. Check the rims for signs of
excessive wear, dings, dents and cracks.
Your bike should be serviced regularly by a qualied mechanic.
Q. Importance of using genuine spare parts.
When you replace components, you must use genuine spare parts to ensure good
performance and reliability. This procedure must be carried out by a qualied mechanic.
Warning! When replacing the pedals, wheels, mud guard or crank, the minimum
distance between the edge of the wheel or mud guard and the pedal axle must exceed
the measurements given below.
Minimum Distance D
D>89 mm for road bikes and children's bikes
D>100 mm for mountain bikes and city bikes and trekking
STOP
Chain ring
Cog
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw BTwin 2013 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van BTwin 2013 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info