630470
8
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
8
K. Attaching non-mounted components that come with the bike.
All our bikes are assembled in accordance with national legislation.
Non-mounted components that come with the bike need to be
attached by a qualied and experienced mechanic.
For BMX bikes, you need to contact a qualied mechanic
to ensure that the pegs are correctly installed.
L. Lubrication
It's important to lubricate bike components to keep your bike running well, to maximize its lifespan and avoid component
corrosion.
Use a special transmission oil for drive train parts. You're advised to use a special oil for the chain. After washing: dry, oil drive train
components (derailleur, lever), suspension, brake levers, brake caliper axles as well as the chain. To ensure proper sealing, oil the
seat post and headset thoroughly.
Warning: Lubrication of bike components - apart from the chain - should be carried out by a qualied and experienced mechanic
during regular servicing.
M. Adjusting chain tension
If the bike has a derailleur, the chain will automatically be stretched. If you have a single gear bike or a bike equipped with
integrated hub gears, it's important to check the chain tension periodically
(slack in the chain can cause the chain to derail, leading to a fall; a chain that is
too tight can adversely aect the bike's performance).
To ensure the chain runs smoothly, there must be a vertical travel of 1 cm,
measured at the half way point between the cog and the pedal.
Chain tension and adjustment for all other gear systems should be carried out
in accordance with component manufacturer's instructions which can be found
on www.btwin.com
N. Adjusting gears and gear use
To adjust gears, refer to the component manufacturer's instructions which can be found on www.btwin.com.
The gears must be adjusted as follows:
This is a tricky procedure so you are advised to contact one of our qualied
technicians.
Note: Problems with changing gear are often linked to the derailleur cable
tension;
you are less likely to have to adjust the derailleur movement.
1 - Adjusting rear derailleur movement
To prevent the chain slipping o the cogs (falling into the wheel spokes
or between the rear dropout and cogs), you need to adjust the derailleur
movement, using H and L stop screws:
Use screw H to adjust the lower stop (small cog side): undoing this screw
moves the chain outward towards the small cog.
Use screw L to adjust the upper stop (large cog side): undoing this screw
moves the chain outward towards the large cog.
2 - Adjusting front derailleur movement
1 cm
Derailleur
stop
Cable xing bolt
Stop screw H
Stop screw L
Cable xing
bolt washer
Cable xing bolt
Chain guide outer
plate
Chain guide inner
plate
Chain
Chain
ADJUSTING OUTER STOP
SCREW
ADJUSTING
INNER STOP
SCREW
Adjusting inner stop
By turning the outer screw of
the derailleur in direction A, the
derailleur will move towards the
smallest chain ring; by turning it in
direction B, it will move away from
the large chain ring. Then adjust
so that the clearance between the
chain guide inner plate and the
chain is between 0 and 0.5 mm.
Adjusting outer stop
By turning the inner screw of
the derailleur in direction A,
the derailleur will move away
from the smallest chain ring;
by turning it in direction B, it will
move towards the large chain ring.
Then adjust so that the clearance
between the chain guide outer plate
and the chain is between 0 and 0.5 mm.
3- Adjusting derailleur tension
Adjusting the cable tension creates a link between a position on the gear lever and a position in the gear system. Unscrew or
tighten the cable tension screw at the lever or at the rear of the derailleur so that each lever position corresponds to a cog:
=> If the chain does not move down every time you shift the lever:
• loosen the cable by turning the cable tension adjusting screw clockwise.
=> If the chain does not move up every time you shift the
lever:
• tighten the cable by turning the cable tension adjusting
screw anticlockwise.
The adjusting screw supplied can be used to:
- Fit or dismantle the gears
- Adjust the handlebars
- Adjust the seat
- Fit or dismantle the wheels.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw BTwin 2013 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van BTwin 2013 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info