519344
17
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
Replacing cutting off wheel -
16
1. Loosen the screws (29) and remove the covering cap
(28).
2. Put the ring spanner wrench (36) on the flange and the
installation wrench (35) on the motor shaft end and
loosen the flange (32).
L Left-handed thread!
3. Remove the flange.
4. Now you can remove the cutting-off wheel (33).
5. The installation of the cutting-off wheel is carried out in
reverse order.
L Observe the rotational direction!
6. Fasten the flange tightly.
L Left-handed thread!
7. Screw on the covering cap (28).
Carrying out angle cuts
When performing the adjustment works pay attention to
that the machine is switched off and pull the saw head
backwards.
Adjusting from 0° – 90 °
1. Loosen the star handled nut (14) and turn the angle
stopper (13) until the desired angle is indicated on the
scale (0°- 90°).
2. Refasten the star handled nut in order to fix the adjusted
angle.
3. Put the tile on the stop rail (11) and the angle stopper
(13).
4. Start the machine and wait until the cooling water is
flushed to the cutting-off wheel.
5. Pull the cutting unit (18) by moving the handhold (23)
slowly and constantly through the tile.
6. Switch off the machine after finishing the cut.
Setting of mitre cut (jolly cut)
1. Loosen the set screws (24) on both sides of the machine
and pull then the cutting unit (18) by moving the handhold
(23) to the desired position until the desired angle is
indicated.
2. Refasten the set screws (24).
3. Carry out the cut as described in point „Adjusting from 0°-
90°“.
Maintenance and cleaning
Before each maintenance and cleaning
work
switch off device
wait for standstill of the radial tile
cutter
pull out main plug
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
E
F
Use only original parts. Other parts can result in unexpected
damages and injuries.
E
L
Observe the following in order to keep the operability of
the radial tile cutter :
F
Clean and oil all moving parts regularly.
Remove dust and dirt with a cloth or a brush.
Do not clean the machine with running water or high-
pressure cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol,
etc.) as these can damage the synthetic parts.
Clean the collecting trough and the cooling water pump
after each application in order to guarantee the cooling of
the cutting-off wheel.
L
Never use any grease!
Use for instance environmentally acceptable spray oil.
Transport
Remove the mains plug before each
transport.
H
L
Transport the radial tile cutter only when the cutting unit
is fixed:
Loosen the star handled nuts of the stopper (17).
Push transportation locks to the cutting device (18).
Refasten the star handled nuts.
That's how you avoid injuries on the hands.
H
Storage
Remove the mains plug
from the socket.
G
Store unused equipment in a dry, locked place out of the
reach of children.
Before a longer storage observe the following in order to
prolongate the service life of the machine and to guarantee
a smooth running operation:
G
thoroughly clean the machine
treat all movable parts with an environmentally friendly
oil
L
Never use any grease!
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika ST 200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika ST 200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 9,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Atika ST 200

Atika ST 200 Installatiehandleiding - Nederlands, Deutsch, English, Français, Italiano, Polski, Dansk - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info