519344
16
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
15
Preparing for commissioning
L
To achieve perfect function of the machine, follow the
notes given in these instructions
You have to attach the following parts:
Base frame
Cooling water pump
Assembly of the base frame and the cooling water
pump -
1. Assemble the main pillars (1) with the screws (4) and the
spring washers (5) on the frame.
2. Screw the clamp holders (6) with the star handle nuts (7)
and the coach bolts (8) on the frame (3).
3. Put the trough (9) into the frame (3).
4. Put the cooling water pump (26) into the intended gap of the
trough.
5. Fill water into the trough until the cooling water pump is
covered with water.
6. Put the radial tile cutter into the trough.
Commissioning
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug
L
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
Use connection cable or extension cable respectively with
a cross section of at least 1,5 mm².
Daily checks of the PRCD (residual-current-operated
circuit breaker)
The device must be connected via the residual-current-
operated circuit breaker (PRCD).
„Reset“
„Test
Perform this check once in a
day.
When changing the location
no further test is required.
1. Directly plug the PRCD into the outlet (vertical).
2. Press the green Reset key – you will hear a click and the
indicator will light up orange.
3. To check the PRCD press the blue test key. The indicator
panel should no longer light.
4. Press the Reset key again – the indicator panel will
light up orange.
5. The machine can be startet.
Switch on
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the PRCD is operative: indicator panel orange.
Press the green button ( I ) on the
switch. At the same time, check
whether the rotating direction of the
cutting-off wheel corresponds to
the indicated rotational direction on
the protection cover (arrow).
L
If there is a power cut, the machine switches off automati-
cally. To switch on again, first press the red and then the
green button.
B
D
B
C
D
Switching off
Press the red button ( 0 ) on the switch.
Working instructions
Before commencing work, ensure the
following:
Workplace tidied?
Is the radial tile cutter stably mounted?
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Working with the radial tile cutter
Keep your hands always in a safe distance to the
rotating cutting-off wheel.
Do not start working before the cutting-off wheel has
reached its maximum rotational frequency.
Pay attention to that the cooling water pump (26) washes
water to the cutting-off wheel.
Only workpieces which have been securely mounted and
aligned can be processed.
Ensure that you always comply with the safety
instructions given on p. 13 ff.
Adjustments on the radial tile cutter
Replacing cutting-off wheel
Before replacing the cutting-off wheel pull
out the power plug.
Do not use any damaged cutting-off wheels or such which
have changed their shape.
Only use sharp cutting-off wheels.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika ST 200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika ST 200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 9,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Atika ST 200

Atika ST 200 Installatiehandleiding - Nederlands, Deutsch, English, Français, Italiano, Polski, Dansk - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info