519272
21
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
What type of logs can I split?
Size of logs
Length: max. 1350 mm
Diameter: min. 120 – max. 400 mm
The log diameter is a recommended guideline figure,
because:
thin logs can be difficult to split if they contain knots or if
the fibres are too strong.
logs with a diameter of over 400 mm can be split if the
fibres are smooth and open.
Do not try to split green logs. Dry logs are much easier to
split, and do not cause jams as often as green (damp) wood.
20
Operation
Two-hand operation
Never operate the log splitter with two people.
Never block the control handles (clamping claws).
1. Press the green switch on the electric motor. Wait a few
moments until the motor has reached its operating
revolutions and the required pressure has been built up in
the hydraulic pump.
L Check the direction of the motor in the log splitter
with threephase motor (400 V 3~), because operation in
the wrong direction damages the oil pump.
L At temperatures below –5° C, let the log splitter run
for at least 15 min. in neutral to heat up the oil.
2. Place the log on the log splitter table.
L Only split the logs in the direction of the wood fibres.
3. Hold the log tight with the clamping claws.
4. Press both operating handles down simultaneously:
Î The splitting blade falls down and splits the log.
5. Release the two control handles, the splitting blade
returns to its initial position.
L If you only release one control handle, then the
splitting blade remains where it is.
Special instructions for splitting logs:
Preparations:
The logs to be split should be cut to the maximum
dimensions. Ensure also that the logs are cut straight and
square.
Place the log properly on the log splitter, so as not to cause
any risk of stumbling or falling to the operator.
Adjusting the stroke height
In case of shorter wood pieces the efficiency can be
increased by shortening the return of the splitting cutter.
1. Place the log on the
splitting table and
press the two control
handles to bring the
splitting blade down to
approx. 3 - 5 cm
above the log.
2. Release one control
handle so that the
blade stays in this
position.
3. Switch the machine
off and disconnect the
power.
9
10
8
4. Release the second control handle.
5. Shorten the return path at the rod fitted to the side by
fixing the holding screw at the necessary height.
11
Holding screw
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika ASP 10-1350 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika ASP 10-1350 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 5,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info