628507
102
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EF1210 U
SER
M
ANUAL
A-10 http://www.aspi.com Copyright © 1999, All Rights Reserved
If you selected only one of the Zone Outputs, repeat for the second Zone Output.
Check Acoustic Gain.
iii. At this point you are ready to calibrate the absolute maximum room audio ampli-
fication level. For this step, you should ensure that the microphones have been
returned to their normal operating location and orientation. This procedure uses
a known nominal electrical noise signal level at the zone output to let you see if
any of the microphone input channels will exceed the permissible acoustic gain
during normal conferencing operation. The level of this noise signal is such that
if any microphone input channel registers more than three green LEDs on the
EF1210 I
NPUT
S
IGNAL
L
EVEL
M
ETER
, the acoustic gain limit of that microphone
channel has been reached. This represents the maximum amplification that may
be applied to the room audio. The room audio may be run at any level below this
threshold, but should not be amplified beyond this level unless the acoustic gain
is reduced by some other means (see the Troubleshooting section in the EF1210
User Manual).
All microphones should be checked in this step as verification that no micro-
phone inputs or zone outputs have been miscalibrated.
As above, both Zones can be adjusted at the same time (both AEC A and AEC B
LEDs will be lit indicating Zone A and Zone B). This is recommended because
you can check all Input Channels at the same time. Alternatively, if necessary,
you may select either Zone by pressing R
EF
S
ELECT
until the appropriate AEC
LED is lit and check one Zone at a time.
You should start by selecting (from the radio buttons labeled 1 through 8) and
checking the microphone input channel which is closest to the loudspeakers or
the microphone which might be expected to pick up the most acoustic energy
from the loudspeaker audio, as appropriate. Check the acoustic gain of this
microphone using Step a, then quickly step through each of the microphone
channels to verify that no other microphone has a stronger signal.
Check and make adjustments for acoustic gain by doing the following:
a. Adjust the external room audio amplifiers/loudspeakers until either:
The loudspeaker audio level is about to become uncomfortably loud.
OR
Three green LEDs on the EF1210 I
NPUT
S
IGNAL
L
EVEL
M
ETER
are lit, but
the first yellow (0 dB) LED is not lit for the chosen input channel
b. Next, step through the microphone input channels by choosing each input
channel from the radio buttons labeled 1 through 8, while verifying for each
channel that the first yellow (0 dB) LED is not lit on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
.
If the first yellow (0 dB) LED is lit for any channel, turn down the room
audio amplifier on the corresponding zone output or turn down the gain on
that microphone channel.
c. When all input channels have been checked, you can mark the positions of
Note.
Do not turn up the room audio level at any point after Step a.
102

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info