628507
100
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EF1210 U
SER
M
ANUAL
A-8 http://www.aspi.com Copyright © 1999, All Rights Reserved
The default choice is pink noise played in both Zone A and Zone B.
Choose “No noise generated” for no pink noise in Zone A and Zone B.
Choose “Pink noise to Zone A” for pink noise in Zone A.
Choose “Pink noise to Zone B” for pink noise in Zone B.
ii. Select input channel to calibrate.
iii. You will need a Sound Level Meter (SPL Meter) for this step. Adjust micro-
phone and loudspeaker to attain the appropriate dB SPL at the microphone using
the following steps:
Set the SPL meter to C weighted, slow response. Choose the appropriate dB
SPL range using Table 7 below based on microphone type and the talker’s
distance from the microphone.
Place the SPL meter beside the microphone. Point the SPL meter and the
microphone toward the loudspeaker.
Adjust the microphone/loudspeaker so that a nominal dB SPL level based on
Table 7 is registered at the microphone.
iv. Adjust level until the first yellow LED (0 dB) on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
of the EF1210 front panel is lit.
v. Repeat for each input channel or click the Apply Gain to All button to
apply the Input Gain to all input channels. Return all microphones to their nor-
mal operating location and orientation.
vi. After all input channels have been calibrated, press the Next button at the bot-
Table 7: Typical distance from microphone to talker and appropriate dB SPL level.
M
ICROPHONE
T
YPE
T
YPICAL
D
ISTANCE
FROM
T
ALKER
(
FT
.)
SPL L
EVEL
(dB)
Lavalier 6 inches to 1 foot 89 dB SPL
Gooseneck 1-2 feet 77 dB SPL
Boundary or other tabletop 2-3 feet 73 dB SPL
Ceiling 4 or more feet 69 dB SPL
Note.
Always double check the microphone level with normal speech
once the microphones are in normal operating position. Actual
speech levels may vary depending on room reverberation, etc.
Verify that you set a reasonable level (three green LEDs and one
solid yellow LED, or 0 dB) by actually talking and looking at the
meter.
Note.
It is vital to move the SPL meter and/or microphones so that each
microphone sees the correct dB SPL acoustic level as you are cal-
ibrating. Do not assume that because the first microphone sees
the dB SPL level, all other microphones will see the same level
(unless they are moved to occupy the same location as the first).
Note.
Use caution if the microphones lie in two acoustically separated
zones and you are only calibrating one zone. As you cycle through
microphones that lie in the other zone, no activity will be indicated
on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
on the EF1210 front panel.
100

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info