628507
34
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EF1210 U
SER
M
ANUAL
32 http://www.aspi.com Copyright © 1999, All Rights Reserved
As above, both Zones can be adjusted at the same time (both AEC A and AEC B
LEDs will be lit indicating Zone A and Zone B). This is recommended because
you can check all Input Channels at the same time. Alternatively, if necessary,
you may select either Zone by pressing R
EF
S
ELECT
until the appropriate AEC
LED is lit and check one Zone at a time.
Adjust the external room audio amplifiers/loudspeakers until either:
The loudspeaker audio level is about to become uncomfortably loud.
OR
Three green LEDs on the EF1210 I
NPUT
S
IGNAL
L
EVEL
M
ETER
are lit, but
the first yellow (0 dB) LED is not lit for the chosen input channel
2.6. Next, step through the microphone input channels by pressing the I
NPUT
S
ELECT
button, while verifying for each channel that the first yellow (0 dB) LED is not lit
on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
.
If the first yellow (0 dB) LED is lit for any channel, turn down the room
audio amplifier on the corresponding Zone Output or turn down the gain on
that microphone channel.
2.7. When all input channels have been checked, you can mark the positions of the
volume controls on the room audio amplifiers and note that this is the absolute
maximum amplification that may be applied to room audio. This maximum
amplification will be referred to in this manual as the amplifier acoustic gain
limit.
During normal operation, the zone output levels will be set 6 dB lower than the
selected level (amplifier acoustic gain limit) to allow the EF1210 L
EVEL
A
DJUST
con-
trols to apply a volume adjustment to the room audio signal in the range +6 dB to -12
dB.
Refer to Figure 12 on page 31 for further explanation.
C
ALIBRATION
S
TEP
3: C
ALIBRATING
AEC R
EFERENCE
I
NPUTS
3.1. Once the Zone Output channels and room audio amplifier have been calibrated,
press the A
UX
I
N
L
EVEL
/S
ETUP
button again to switch to AEC Reference Input
Note.
You should start by selecting (using the I
NPUT
S
ELECT
button) and
checking the microphone input channel which is closest to the
loudspeakers or the microphone which might be expected to pick
up the most acoustic energy from the loudspeaker audio, as appro-
priate. Check the acoustic gain of this microphone using Step 5,
then quickly step through each of the microphone channels (step 6)
to verify that no other microphone has a stronger signal.
Note
.
Do not turn up the room audio level at any point after Step 5.
Note
.
The volume control may be set at a lower level than this marked
position (amplifier acoustic gain limit), but must not be set higher
or the performance of the echo canceller will be suboptimal.
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info