628507
33
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
A
DVANCED
I
NSTALLATION
ASPI Digital - The Sound of DSP Technical Support: 404.892.3200 31
2.2. Press the R
EF
S
ELECT
button to choose which output is being calibrated. A nom-
inal level noise signal is played through the selected Zone output(s).
When the EF1210 first enters Zone Output calibration, the AEC A and AEC
B LEDs are lit, indicating that both zones will be calibrated. Use this if you
want to calibrate both zones at the same time.
If you want to calibrate only Zone A, press the R
EF
S
ELECT
button to select
Zone A. Only the AEC A LED lights, indicating Zone A.
If you want to calibrate only Zone B, press the R
EF
S
ELECT
button again to
select Zone B. Only the AEC B LED lights, indicating Zone B.
2.3. Check the specifications of your room audio amplifier input:
If it expects consumer level (-10 dBV) input, press the L
EVEL
A
DJUST
D
OWN
button once.
If it has a balanced input connector and expects 0 dBu input level, press the
L
EVEL
A
DJUST
U
P
button once.
More precise level adjustments can be made with the RS-232 commands (see the
GAINZ command on page 68 of the Command Set Reference.
2.4. If you selected only one of the Zone Outputs, repeat for the second Zone Output.
For visual instructions, refer to Figure 12 on page 31.
Check Acoustic Gain.
2.5. At this point you are ready to calibrate the absolute maximum room audio ampli-
fication level. For this step, you should ensure that the microphones have been
returned to their normal operating location and orientation. This procedure uses
a known nominal electrical noise signal level at the zone output to let you see if
any of the microphone input channels will exceed the permissible acoustic gain
during normal conferencing operation. The level of this noise signal is such that
if any microphone input channel registers more than three green LEDs on the
EF1210 I
NPUT
S
IGNAL
L
EVEL
M
ETER
, the acoustic gain limit of that microphone
channel has been reached. This represents the maximum amplification that may
be applied to the room audio. The room audio may be run at any level below this
threshold, but should not be amplified beyond this level unless the acoustic gain
is reduced by some other means (See “Acoustic Gain” on page 44).
All microphones should be checked in this step as verification that no micro-
phone inputs or zone outputs have been miscalibrated.
Figure 12. Calibrating Zone outputs
AUX IN
LEVEL
REF
SELECT
INPUT
SELECT
SETUP
AEC
A
AEC
B
12345678
INPUTPOWER REMOTE
MUTE
ALL
LEVEL
ADJUST
SETUP
STEP 2.6: adjust external
amplifiers/loudspeakers so that
no more than 3 green LEDs are
lit (repeat for each channel)
-12 -7 -3 0 3 20 dB -12 -7 -3 0 3 20
STEP 2.2:
press to select
noise source
noise to both zones (recommended)
noise to zone A
noise to zone B
STEP 2.6: press
to select
channel;
check level
LEDs light to
indicate which
channel is selected
LED blinks
twice for Zone
calibration
STEP 2.3a: press
if amp expects
consumer level
input (-10 dBV)
STEP 2.3b:
press
if amp
expects 0 dBu
balanced input
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info