702286
10
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
10 ATS7100/7110 Installation and Troubleshooting Guide
LED LED 1 –
Status
LED 2 - Call
Status (B-
channel)
LED 3 - X25
Call Status
1
Off Hardware
failure
Offline Offline
Flash Operational
2
Call setup in
progress
2
Call setup in
progress
2
Blink Local S0 bus
failure
Incoming call
present
Pause
before
reconnect
On Line fault,
network
failure
Online Online
Table 2. ATS71xx status LEDs
Notes:
1
ATS7110 only
2
A running light on all the three leds indicates the unit
is initialising.
2.5. Programming the ATS7100
The minimum programming settings for the ATS7100
are:
Menu Description Comments
19.9 Reporting format Per Central Station
19.9 Phone number 1 Per Central Station
19.9 System account
number
Per Central Station
19.9 Area account number Per Central Station
and Area
19.9 Select ISDN dialler Per Central Station
19.9 Connection type 1 – ISDN
Per Central Station
For Panel firmware
V04.00.00 and
higher
Table 3. ATS7100 minimum settings
For further programming details see the ATS
2000/3000/4000/4500 programming manual.
2.6. Programming the ATS7110
The minimum programming settings for the ATS7110
are:
Menu Description Comments
19.9 X25 TEI value Belgium: 1
Netherlands: 2
19.9 X25 D-Bit Belgium: No
Netherlands: Yes
19.9 Reporting format X25 ENAI
Per Central Station
19.9 Phone number 1 Per Central Station
19.9 System account
number
Per Central Station
19.9 Area account number Per Central Station
and Area
19.9 Select ISDN dialler Per Central Station
19.9 X25 Account Code Per Central Station
19.9 Connection type 2 – ISDN-D
Per Central Station
For Panel firmware
V04.00.00 and
higher
Table 4. ATS7110 minimum settings
For further programming details see the ATS
2000/3000/4000/4500 programming manual.
Using Titan
In general no events will be reported to the Central
Station while Titan is on-line to the panel. Due to
shared resources some limitations apply when
connecting Titan to a system to which an ATS7110 is
connected.
When Titan is used via J18 using the
ATS1830/ATS1834 cable, no events can be
reported via D-Channel X25 as long as the cable is
connected. Disconnect cable from panel when
ready.
Start a local J18 Titan connection by typing
*<installer code>Enter, select menu 7. Do not
select installer menu 19, since doing so initiates
the transmission of the LB event. When the
ATS1830/ATS1834 cable is already connected, the
ATS7110 will not be able to transmit this event,
and both event reporting and Titan are blocked.
2.7. Line monitor/guard (ATS7100
and ATS7110 in B-channel
mode)
The line monitor is activated by setting the menu
“Activate ISDN line monitor” to “YES” (see menu 9). If
enabled, the ATS7100/7110 ISDN checks whether the
S0 bus is activated or not. If the S0 bus is not activated,
it will initiate an activate request to the network and wait
for 12 seconds for the S0 bus to be activated. If there is
no response from the network, the ATS7100/7110
ISDN disconnects the outgoing S0 bus (CONN4) from
the network by its internal relay and initiates another
activate request to the network.
If there is still no response, the network has failed. The
ATS7100/7110 ISDN will then report a line fault to the
panel. The outgoing S0 bus was probably not the cause
of the line fault and will therefore be re-connected to the
network. The ATS7100/7110 ISDN keeps trying to
activate until the network is back.
However, if the network does respond after
disconnecting the outgoing S0 bus (CONN4), the
outgoing S0 bus caused the line fault. The
ATS7100/7110 ISDN keeps the outgoing S0 bus
disconnected to ensure proper operation. From then on
it will reconnect the outgoing S0 bus every hour to test
whether the S0 bus problem has been solved or not.
This state will be remained until the S0 bus is
operational. As it is still possible to transmit alarm
events, there will be no line fault reporting to the panel.
2.8. Troubleshooting
LEDs indicating operation/trouble mode (see table
4 and 5).
Speaker connector
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech ATS7100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech ATS7100 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info