578804
6
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
E-6
Stereo system with no LFE
This is a typical two-channel system (such as Arcam’s
Solo). Logo is connected to L/R preamplifier outputs.
The crossover frequency on Logo should be
adjusted to the low frequency roll off of the main
speakers (see the manual for your speakers for this
information). The Q-control (
X-OVER Q) can be used
to fine-tune the integration of Logo and your main
speakers.
Sub/sat system
This is a surround-sound system (such as Arcam’s
Solo Movie 5.1) where all the main speakers are
satellite speakers, defined as ‘Small’. Logo is connected
to output marked
SUB, SUBWOOFER or LFE.
The LFE input bypasses the crossover in Logo, so the
crossover frequency should be set by the surround
sound amplifier. For the crossover setting, please see
the response of your satellite speakers which may
vary from around 70Hz for large satellites, to 150Hz
for small satellites. We recommend 80Hz as a starting
point if you are unsure.
Sub/full range+sat system
This is a surround-sound system (such as Arcam’s
Solo Movie 5.1) where full range L and R speakers
are combined with satellite (or with full range) rear
speakers. The system should be connected with
both the
SUB, SUBWOOFER or LFE output connected to
IN LFE and Left/Right preamplifier outputs attached to
IN L/IN R on Logo.
In such systems, Logo can be set up to work with two
crossover frequencies. One frequency is set up for the
rear speakers using the surround amplifier crossover,
and one frequency for the full range Left and Right
speakers, using the Logo crossover.
Direct mode in Arcam
surround amplifiers
If you wish to have your system set up to use
the crossover in the surround amplifier for 5.1
or 7.1 material, but use Left and Right full range
speakers with Logo filling in for two-channel
material, you can use Direct mode.
Connect the amplifier and Logo as in the
Sub/full range+sat system diagram. In the
amplifier, set up all speakers to ‘Small’; this
redirects bass to Logo via the LFE channel. To use
the system’s full range, activate ‘Direct mode’ for
two-channel sources. This sends the full range
signals to the Left and Right speakers and use the
IN L/IN R inputs to Logo via its own crossover.
connection
L- R-
IN L
IN R
PRE OUT
LEFT
PRE OUT
RIGHT
L+ R+
R-R+
L-L+
LS
RS
C
L
R
IN LFE
IN L
IN R
PRE OUT LEFT
PRE OUT RIGHT
PRE OUT SUB
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam Logo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam Logo in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info