578804
4
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
E-4
Positioning the unit
< Place the Logo speaker unit on a level, firm
surface, avoiding direct sunlight and sources of
heat or damp.
< Do not place Logo in an enclosed space such
as a bookcase or closed cabinet unless there is
good provision for ventilation. The Logo speaker
unit is designed to run warm during normal
operation.
< Do not place your record deck on top of Logo.
Record decks are very sensitive to the noise
generated by mains power supplies which will
be heard as a background ‘hum’ if the record
deck is too close. Vibrations from Logo may also
cause the pickup stylus to jump tracks.
Power
Logo is supplied with a moulded mains plug already
fitted to the lead. Check that the plug supplied fits
your supply – should you require a new mains lead,
please contact your Arcam dealer. Logo is fitted with
a transformer designed to accept nominal mains
voltages from 100V to 240V.
Push the IEC plug end of the power cable into the
socket on the back of Logo, making sure that it is
pushed in firmly. Plug the other end of the cable into
your mains socket and, if necessary, switch the socket
on.
Logo is fitted with a main power switch on the rear
panel, above the power inlet: make sure that this is
switched on to use Logo.
If your Logo is not to be used for a prolonged period,
switch the unit off at the main power switch.
Indicator LED
An indicator LED is positioned across
the top edge of Logo’s cabinet.
When the indicator LED is off, it
indicates that the speaker is completely
disconnected from the mains. A blue
light from the indicator shows that the speaker is
powered up and ready for immediate use. A red
light from the indicator shows that the speaker is in
standby (power-saving) mode and will power up as
soon as an audio signal is received.
Standby switch
The push-in STANDBY switch provides two
settings:
AUTO and MANUAL.
AUTO (button out) switches Logo’s
amplifier to standby after a period of
idleness (about 15 minutes) when no audio signal has
been received.
MANUAL (button in) means that Logo’s
amplifier is on whenever the unit is receiving mains
power.
Interconnect cables
We recommend the use of high-quality screened
audio interconnect cables. Poor quality cables will
degrade the performance of your system. All cables
should be kept as short as is practically possible.
It is good practice when connecting your equipment
to make sure that the mains power-supply cabling is
kept as far away as possible from your audio cables.
Failure to do so may result in unwanted noise in the
audio signals.
installation
Connecting to a sound source
Check that your sound processor/receiver is switched
off before connecting Logo. Failure to do this may
result in both speaker and amplifier damage.
If your sound source has a
PRE-OUT SUB or LFE OUT
output, connect this to
IN LFE on the back panel using
RCA (phono) connectors at each end. If your sound
source does not have a SUB or LFE output, connect
the left and right channels of the stereo pre-amp
output (
PRE OUT L and PRE OUT R) to IN L and IN R,
respectively.
You may connect both the
LFE and the L and R
outputs to Logo if you wish to use both the LFE
channel and to supplement the bass response of
‘Large’ Left and Right speakers.
OUT L, OUT R and OUT LFE provide line-level outputs
for ‘daisy-chaining’ further units, in a multi-room
installation, for example.
After connecting
Turn the sound source amplifier volume down to
minimum before switching on. Switch the source
amplifier on, select a source signal, then gradually
increase the volume to the required listening level.
Care of your speaker
Running-in
In the same way as a new car requires a ‘running-in’
period, so do all loudspeakers. Your Logo may sound
good when you first connect it, but with time it will
improve dramatically. Expect about 50 hours use
before the full potential of your Logo is realised.
Cleaning
To clean your speaker simply use a soft, slightly
dampened cloth to wipe off any dust or dirt. Do not
use solvent-based or chemical cleaning products as
these may damage the finish of the speaker cabinet.
Power handling
Arcam speakers are designed to reproduce recorded
music under normal domestic conditions. We do
not recommend nor warrant them for commercial
applications, such as discothèques, public address, etc.
Note: When connecting Logo to signal leads,
or when moving Logo to a new position, make sure
that the unit is not receiving power by switching off
and disconnecting the power lead.
AUTO
MANUAL
STANDBY
IN
L
R
LFE
ON OFF
OUT
L
R
LFE
100-240V~50/60HZ 275W MAX
FUSE: T2.5AL 250V
USE ONLY WITH A 250V FUS E
PHASE STANDBY
AUTO
MANUAL
0.3
0.5
0.7
0.9
1.1
1.3
1.5
X-OVER Q
VOLUME
0
1
2
3
4
5
6
7
8
9
10
35
50
70
85
100
115
125
140
160
X-OVER FREQ
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam Logo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam Logo in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info