Handleiding Alpina TR 250 J (pagina 11 van 24) (Alle talen)

731989

Verklein

Vergroot

Pagina terug

1/24

Pagina verder

saw dust, branches, leaves, or excessive grease;

ne ver leave containers with the cut debris inside

the storage area.

5) If the fuel tank has to be emptied, this should be

done outdoors once the engine has cooled down.

6) Always wear protective gloves when handling

the cutting device.

7) For safety reasons, never use the machine

with worn or damaged parts. Damaged parts

are to be replaced and never repaired. Only

use original spare parts. Parts that are not of the

same quality can seriously damage the equipment

and compromise safety. The cutting tools must

always bear the manufacturer’s trademark as well

as a reference to the maximum working speed.

8) Before putting the machine away, check you

have removed wrenches or tools used for main-

tenance.

9) Store the machine out of the reach of children!

E) TRANSPORTATION AND HANDLING

1) Whenever the machine is to be handled or

transported you must:

– turn o the engine, wait for the cutting device to

stop and disconnect the spark plug cap;

– only hold the machine using the handgrips and

position the cutting device in the opposite direc-

tion to that used during operation.

2) When using a vehicle to transport the machine,

position it so that it can cause no danger to per-

sons and fasten it rmly in place to avoid it from

tipping over, which may cause damage or fuel

spillage.

F) HOW TO READ THE MANUAL

Certain paragraphs in the manual contain particu-

larly signicant information and are marked with

various levels of highlighting with the following

meaning:

NOTE

IMPORTANT These give details or further

information on what has already been said, in the

aim to prevent damage to the machine.

WARNING! Non-observance will re-

sult in the risk of injury to oneself or others.

DANGER! Non-observance will re-

sult in the risk of serious injury or death to

one self or others.

2) Mow only in daylight or good articial light.

3) Take on a rm and well-balanced position:

– where possible, avoid working on wet, slip-

pery ground or in any case on uneven or steep

ground that does not guarantee stability for the

operator;

– never run, but walk carefully paying attention to

the lay of the land and any eventual obstacles;

– assess the potential risks of the ground to be

mown and take all necessary precautions to en-

sure your own safety, especially on slopes or on

bumpy, slippery or unstable ground;

– work along the contour on slopes, never when

walking up or down and always keep downhill

of the cutter.

4) Make sure the machine is securely locked

when you start the engine:

– start the motor in an area at least 3 metres from

where you refuelled;

– check that there is nobody within at least 15 me-

tres of the machine’s range of action;

– do not direct the silencer and therefore the ex-

haust fumes towards inammable materials.

5) Do not change the engine governor set-

tings or overspeed the engine.

6) Do not strain the machine too much and do not

use a small machine for heavy-duty works. If you

use the right machine, you will reduce the risk of

hazards and improve the quality of your work.

7) Check that when the machine is running idle,

there is no movement of the cutting device and, af-

ter pressing the throttle trigger, the engine quickly

returns to minimum speed.

8) Stop the engine:

– whenever you leave the machine unattended.

– before refuelling.

– during movements between work areas.

9) Stop the engine and disconnect the spark

plug cable:

– before cleaning, checking or working on the ma-

chine;

– after striking a foreign object. Inspect the ma-

chine for any damage and make repairs before

restarting it again;

– if the machine starts to vibrate abnormally: nd

the cause of the vibration immediately and have

it inspected at a Specialised Centre;

– when the machine is not in use.

D) MAINTENANCE AND STORAGE

1) Keep all nuts, bolts and screws tight to be sure

the equipment is in safe working condition. Rou-

tine maintenance is essential for safety and

for maintaining a high performance level.

2) Do not store the machine with fuel in the tank

in an area where the fuel vapours could reach an

open ame, a spark or a strong heat source.

3) Allow the engine to cool before storing in any

enclosure.

4) To reduce re hazards, keep the engine, ex-

haust silencer and fuel storage area free from

SAFETY REQUIREMENTS

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Alpina TR 250 J Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info