Handleiding Alpina ABR 26 JD (pagina 18 van 27) (Alle talen)

731917

Verklein

Vergroot

Pagina terug

1/27

Pagina verder

13) Do not store the machine with fuel in the tank

in an area where the fuel vapours could reach

an open ame, a spark or a strong heat source.

14) Allow the engine to cool down before storing

in any enclosure.

15) To reduce re hazards, clean the machine

and especially the engine thoroughly to get rid

of any grass cuttings, leaves or excess grease,

never leave containers with the cut debris inside

the storage area.

16) If the fuel tank has to be emptied, this should

be done outdoors once the engine has cooled

down.

17) Before putting the machine away, check you

have removed wrenches or tools used for main-

tenance.

E) RESIDUAL RISKS

1) Even when all safety prescriptions are com-

plied with, there may be certain residual risks

that can not be excluded. Potential foreseeable

hazards depend on the type and construction of

the machine and can include:

– Injuries to ngers and hands if caught in the ro-

tation of the cutting means

– Injuries to feet if struck by the cutting means

– Injuries to eyes if protection goggles are not

worn (hurling of stones and soil)

– Injuries to hearing ability if no ear protection

devices are worn.

F) TRANSPORTATION AND HANDLING

1) Whenever the machine is to be handled or

transported you must:

– Turn o the engine, wait for the cutting means

to stop and disconnect the spark plug cap;

– Fit the cutting means guard;

– Only hold the machine using the handgrips

and position the cutting means in the opposite

direction to that used during operations.

2) When using a vehicle to transport the ma-

chine, position it so that it can cause no danger

to persons and fasten it rmly in place to avoid it

from tipping over, which may cause damage or

fuel spillage.

G) ENVIRONMENTAL PROTECTION

1) Environmental protection should be a priority

of considerable importance when using the ma-

chine, for the benet of both social coexistence

and the environment in which we live. Try not to

cause any disturbance to the surrounding area.

2) Scrupulously comply with local regulations

and provisions for the disposal of packaging,

oils, petrol, lters, damaged parts or any ele-

ments which have a strong impact on the envi-

ronment; this waste must not be disposed of as

normal waste, it must be separated and taken to

specied waste disposal centres where the ma-

terial will be recycled.

3) Scrupulously comply with local regulations

for the disposal of waste materials after mowing.

4) At the time of decommissioning, do not pol-

lute the environment with the machine, hand it

over to a disposal centre, in accordance with the

local laws in force.

OPERATING INSTRUCTIONS

NOTE - The figures mentioned in the text

are found on page iii and following of this

manual.

1. MACHINE ASSEMBLY

IMPORTANT The machine is supplied with

some of the components disassembled and the

fuel tank empty.

WARNING! Always wear strong protec-

tive gloves to handle the cutting devices.

Mount the components very carefully so as

not to impair the safety and efficiency of the

machine. If in doubt, contact your dealer.

WARNING! Unpacking and completing

the assembly should be done on a flat and

stable surface, with enough space for moving

the machine and its packaging, always mak-

ing use of suitable equipment.

Disposal of the packaging should be done in ac-

cordance with the local regulations in force.

1.1 COMPLETING THE MACHINE (Fig. 1)

– Position the upper part (1) of the front handgrip

and apply the lower cap (2) using the screws

(3), making sure the two anti-vibration halves

of the shell remain in position (4)

– Before tightening the screws (3), align the

handgrip correctly with respect to the drive

tube.

– Fully tighten the screws (3).

1.2 FITTING THE GUARD (Fig. 2)

– Remove the guard plug (1) from the end of the

bottom part of the rod (2).

– Secure the guard (3) to the support (4) using

the supplied bolts (5).

1.3 ASSEMBLY AND DISASSEMBLY

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Alpina ABR 26 JD Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info