601590
20
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
en
Cleaning and Maintenance
20 456251_a
5 Turn the safety lever (central catch) and lift
the tube back.
Transportation
For easier transportation, the shredder can be se-
parated in the middle (hinges).
1 Unscrew the nut. (1a)
2 Pull out the rod and take the upper part off.
(1b)
Cleaning inside the housing
Aftrer cleaning the inside of the shredder, we re-
commend that you spray the inside and the blade
disc with a fine oil to prevent corrosion.
Motor is maintenance-free
Remember your "TCS Duotec" has a tough job to
do in shredding branches and shrubs. It is there-
fore, of parampunt importance that the cutters are
kept sharp. The cutters have appreciable less cut-
ting power when blunt. The shred is then coarser
(will not decompose so easily).
Shredder tears rather than cuts when the cutters
are blunt.
Prior to switching the shredder on check taht all
cutters are securely mounted.
Changing and grinding cutters
Assembly:
Included with the shredder is the following:
4 box spanner SW10
1 open-ended spanner SW 10/8
1 Torx-bit T30
CAUTION!
Always switch off the motor and dis-
connect the plug prior to gaining ac-
cess to the cutters!
Make shure the cutters are sharp
when used!
Always keep to the original cutting
edge when regrinding the cutters!
Use new cutters, when necessary!
Wear protective gloves when doing
this, to avoid the risk of injury.
Loosen the countersunk head bolt using the Torx-
bit and open-ended spanner and turn the bldes
180°. (10a)
These blades are double ground and can thus be
used on both sides. When blunt on both sides re-
new, and make sure they are screwed in tightly.
Diassembly of the pre-cutter and blade disc:
CAUTION!
Wear protective gloves when doing this,
to avoid the risk of injury!
Using the allen key, loosen the socket head screw
in the blade holder (keeping the lower blade disc
from burning). (10b)
Now you can lift off the following parts:
Socket head screw with pre-cutter and was-
her. (11)
Upper blade disc. (12)
Distance tube (13)
Lower blade disc.
Assembly is carried out in the reverse sequende.
Replacing the feeder funnel
If the tube will not close down (sticks), turn the
blade disc around 90°.
lift back the tube and engage in the saftey lever
(central catch).
Screw in the handscrew.
CAUTION!
Before puuting into operation check
that the feeder tube has been pro-
perly located and locked with the
central catch!
For replacement og this crew use
only original part!
Disposal
Do not dispose of worn-out machines
or spent batteries (including recharge-
able batteries) in domestic waste!
The packaging, machine and accessories
are made from recyclable materials and
must be disposed of accordingly.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko TCS Duotec 3000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko TCS Duotec 3000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 1,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info