601590
19
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Assembly
456251_a 19
Open the machine
5 loosen the handscrewn (2a).
6 fold back the feeder tube (2b).
7 Place the lower half on the side ans dispose
of the packaging.
8 Position the washers 8,4 x 24 (DIN 9021) and
legs on the housing and insert screws M8 x
35 (3).
9 Attach the legs using the nuts M8 and was-
hers 8,4 x 16 (DIN 125) supplied. (Assembly
the same on left and right side) (4)
ADVICE
For easier assembly of the wheel axle,
do not fully tighten the nuts simply hold
the legs in position the screws.
Assemble wheel axle and wheels
You will need:
1 axle
2 screws M8 x 40
2 washer 8,4 - DIN 125
2 nuts M8
2 wheels with ball bearings
2 extension screws (= wheel axles)
2 nuts M10
2 adjusting washer 15 x 21 x 0,5
2 retainig washer 10,5
1 Using the 2 screws, 2 washers 8,4 and nuts,
screw the axle onto the legs. (5)
2 Ten tighteen the 6 nuts on the legs.
3 Position the lower part of the shredder on the
legs.
4 Place the upper part of the shredder on the
top of the lower part. (6)
5 Allow the upper part to engage int the central
retainer.
6 Push the rod through the holes in the upper
and lower parts of the shredder.
7 Screw the nut back onto the rod. (7)
8 Tighten the handscrew. (2a)
9 The wheels (with ball bearings fitted) are se-
cured to the axle using the extention screw,
adjusting washer 15 x 21 x 0,5, retainig was-
her 10,5 and nut. (8)
10 Fit the wheel covers onto the wheels.
Assembly tools
Included with the shredder is the following:
1 box spanner SW 10
1 open-endde spanner SW 10/8
1 Torx-bitT30
Assembly of feeder funnel
Tools:
1 Screwdriver
4 Bolts M6 x 25
4 Washer A6,4 DIN 9021
1 Fit the projective rubber guard on top of the
tube. (9b)
2 Position the funnel on top of the tube. (9c)
3 Secure the funnel to the tube using the 4
screws and washers. (9d)
Assembly tube
Montage Fülltrichter
Assembly tools:
4 washer 6,4 - DIN 125
4 retaining washer 6,4
1 screw M6 x 25
3 screw M6 x 16
1 Position the tube on top of the shredder. (9a)
2 Secure the tube on top of the shredder.
CLEANING AND MAINTENANCE
CAUTION!
Do not spray with water
Removing feeder funnel
1 Switch off shredder
2 Wait until cutter has com to a complete stop.
3 Disconnect mains plug.
4 Loosen screw and pull out (2a)
CAUTION!
For replacement of this screw only origi-
nal part!
Safety disconnection switch
The safety disconnection switch i acted by pulling
the screw out.
The motor can not be started with the normal ro-
cker switch.
Aftre replacing the feeder funnel with the original
screw, the motor can be re-started with the rocker
switch.
ADVICE
Very important for your own safety!
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko TCS Duotec 3000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko TCS Duotec 3000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 1,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info