460709
12
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
Log splitter
GB 3
Unpacking/Assembly
Caution!
The log splitter should only be used
when all its component parts have been
completely assembled.
1. Check the package contents (Illus. A/B).
Inform the dealer if deficiencies are detected.
Note:
Tools required for assembly/operation
are depicted in Illus. C. These are not
included in the scope of delivery.
Mounting the transport wheels
1. Fit the axle (Illus. 1-2) from outside through
the wheel and through the tube (Illus. 1-1)
and secure it with the spring plug (Illus. 1-3).
Mounting the feet (KHS 5200)
1. Mount the transportation wheels on both the
front feet; see Section “Mounting the trans-
port wheels.”
Warning!
The transportation wheels are only used
to transport the log splitter. During
splitting operation, the wheels must be
removed from the feet and mounted in
the park position (Illus. B-11).
2. Tilt the log splitter on to one side and mount
the front and rear foot.
3. Fit the foot (Illus. 2-2 and Illus. 4-2) up to the
stop limit inside the tubular frame (Illus. 2-1
and 4-1) and secure it firmly in position with
screws, washers, and locking nuts.
4. Tilt the log splitter onto the opposite side with
the help of a second person, and mount the
other feet and afterwards put it upright.
5. Put the log splitter in vertical position (piston
rod upright) and screw the support foot (illus.
3-1) on the rear feet.
6. Erect the log splitter and mount the cross
members in front (Illus 5-1) with the help of
the threaded rod (Illus. 5-1).
Mains connection
1. Connect the cable to the mains supply.
Operation
Caution!
The log splitter should not be operated if
components (e.g. the protective hoops)
are missing or defective or the connec-
tion cable is damaged.
Prior to every use
1. Conduct a visual inspection of the log split-
ter.
2. The log splitter should not be operated if
components are missing, defective or loose.
3. Visually inspect the connection cable. A
defective connection cable (e.g. with cracks,
cuts, crushing damage or bends in the insu-
lation) should not be used.
4. Visually inspect the hydraulic components for
leaks.
Log splitter start-up
Caution!
The log splitter should only be used by
one person.
1. Position the log splitter horizontally on a
level, firm surface, better with a slight inclina-
tion towards the operating lever (since the
valves are seated here). If inclined towards
the splitting wedge it loses splitting force. Do
not deposit the log splitter on the connection
cable!
2. Lay the connection cable so that it cannot be
damaged by bending, crushing or otherwise.
Warning!
The transportation wheels with model
KHS 5200 are only used to transport the
log splitter. During splitting operation, the
wheels must be removed from the feet
and mounted in the park position.
3. Loosen the venting screw (Illus. 6) by 3-4
turns.
Note:
After splitting, tighten the venting screw
(Illus. 6) again .
4. Depending on the length, lay the log such
that the wooden log is held by the log guide
tubes.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko KHS 5200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko KHS 5200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info