594311
16
Verklein
Vergroot
Pagina terug
1/166
Pagina verder
16
Original instructions for use
Do not get the machine wet or expose it to moisture.
Regularly check the machine is in good working order.
Do not use any cleaning agents or solvents. They can
cause irreparable damage to the machine.
Cleaning the guard plate
1. Switch off the machine.
2. Use a screwdriver or a similar tool to remove mowing
residues carefully.
Clean the guard plate regularly in order to avoid
the stem tube overheating.
Changing the spool (Fig. 5)
1. Brace spool head (2) and use spanner (3) to loosen
fastening screw (2) clockwise.
2. Unscrew and remove fastening screw.
3. Pull the spool head off the drive shaft.
4. Remove spool (1) from the spool head.
5. Remove dirt and grass residues.
6. Thread the ends of the cutting lines from the new
spool into the openings provided for them in the spool
head.
7. Insert the spool into the spool head. Make sure that
the cutting lines do not become jammed, and pull
them out of the spool by about 9 cm.
8. Push the complete spool head onto the drive shaft
and tighten anticlockwise with the fastening screw.
9. Hold the spool head rmly and tighten with the
spanner.
Changing the line knife
1. Unscrew and remove the two screws arranged on the
inside edge of the guard plate and remove the old
line knife.
2. Insert the new line knife and screw it on again.
Do not overtighten the screws.
Sharpening the line knife
1. Remove the cutting blade from the guard plate.
2. Secure the line knife in a vice and sharpen it with a
at le.
Only le in one direction!
Trimming at fences and foundations
IMPORTANT!
Do not touch xed structures - danger of kickback!
1. Guide the machine slowly and carefully, without
allowing the cutting line to strike against obstacles.
Trimming around tree trunks
1. Carefully and slowly guide the machine around tree
trunks so that the cutting line does not touch the tree
bark.
2. Mow from left to right around tree trunks.
3. Strike the grass and weeds with the tip of the line, and
tilt the spool head forward slightly.
Trimming along stone walls, foundations and trees
results in increased line wear.
Mowing
1. Slant the spool head at a 30 degree angle to the right.
2. Turn the hand grip to the required position.
IMPORTANT!
Remove foreign bodies from the working area.
Danger of injury/damage to property due to objects
being thrown out.
Maintenance and care
CAUTION!
Danger from electrical current!
Before all maintenance and care jobs, disconnect
the machine from the mains and secure it to
prevent it from being switched back on.
After use, disconnect the mains plug and check the
machine for damage.
Keep the machine out of reach of children and
unauthorised persons.
Electrical malfunctions are only allowed to be rectied
by authorised specialist workshops.
Never use the machine if the blade of the line cutter is
missing or damaged.
Always keep the guard plate, spool head and motor
clear of mowing residues.
Do not spray the machine with water! Penetrating
water can lead to malfunctions.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko AL-KO BC 1000 E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko AL-KO BC 1000 E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info