594592
34
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
Using your brushcutter
ENGLISH 14
7. Using your brushcutter
7.1 Scope of Application
Only use brushcutters fitted with the 3-tooth brush
cutting blade for mowing grass, light brush, reeds
and uncultivated growth at ground level.
Never use the brushcutter for any other purpose.
Using the cutting tools, which are available as
accessories and which are specified for certain
tasks, enable the brushcutter to be used for those
purposes specifically mentioned in the accessory
instructions. Also observe the safety instructions in
those accessory instructions.
Generally, use only the cutting tools authorised for
use with this brushcutter. Always fit the contact
shield specified for this brushcutter and cutting tool. If
in doubt, contact your local SOLO dealer.
7.2 Initial use/ start-up behaviour
When switching on the engine for the first five times
prior to commencing work, first operate for a short
time in the mid-speed range without any load until
the engine has warmed up a little.
7.3 Correct brushcutter operation
Observe the relevant safety instructions when using
the brushcutter.
The rotational direction of the cutting tool makes the
operation on the l.h. side of the cutting tool (from the
operator's viewpoint, subject to the brushcutter being
held correctly section A) particularly free from
kicking. Therefore, always approach the area to be
cut from the right. This brings the l.h. side of the
cutting tool into contact with the material to be
trimmed first. Particularly when cutting tougher
growth (such as medium sized weeds and wild
growth), ensure that you do not "stab" the front of the
brushcutter into the material to be trimmed.
Approach the working area with the brushcutter set to
idle, and then switch to full throttle. Never leave the
engine running at high speed without applying a load.
Dip the tool from the r.h. side 2/3 into the material to
be trimmed. Then work the brushcutter lie a scythe,
i.e. by moving forward step by step, whilst cutting
from right to left.
Operate the brushcutter at full throttle to obtain an
optimum cutting result. Never operate with the clutch
in slipping range. Consequential damage through
excess loads or overheating is excluded from our
warranty.
Immediately stop the engine in case of noticeable
vibrations or when material has gathered around the
cutting tool or contact shield. Slow down the cutting
tool by pressing it onto the ground, until it has come
to a complete standstill. Pull the spark plug cap from
the plug, and clean the tool seat of all grass, roots
etc. Check the entire brushcutter for perfect condition.
7.4 Sharpening instruction for brush blade
When dull, the
cutter blade’s
edges can be
re-sharpened
on both sides
with a flat file
at an angle
of 30°.
All cutting edges need to be filed back equally, if the
wear and tear is substantial, or if there are broken-off
cutting edges. It is necessary to check for imbalance
and if necessary, to make corrections by additional
filing. The sharpening angle is 30°.
Fig. 14
Fig. 15
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko AL-KO 137 SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko AL-KO 137 SB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info