594592
30
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
Preparing the equipment for use
ENGLISH 10
B) Assembly of the nylon line head
When fitting a nylon line head, you will not need the
following components shown in Fig. 5:
Retaining nut (28) (caution: left-handed thread), nut
protector (27), pressure washer (26) and metal
cutting blade.
Fit the anti-winding protection (30) (supplied with
the line head) after the pressure piece (25). The
side of the anti-winding protection labelled with
the number "870" faces the gearbox, so the edge
of the anti-winding protection overlaps the edge of
the bevel gearbox.
Block the shaft with the pin (29).
Screw on the line head by hand. Caution: left-
handed thread.
Fit the protective bar (31) with assembled line
trimmer from underneath onto the guard. Bend
the protective bar slightly in the process.
Important: When using the line head, never
start the brushcutter without the protective bar
and the line trimmer assembled.
If the length of the line has been adjusted (see
chapter 7.5, "Adjusting the cutting line"), the line
trimmer will automatically cut the ends of the line to
the correct length during operation.
When using metal cutting blades, always work
without the protective bar fitted.
C) Assembly of the "Jet-Fit " cutting head
Insert the cutting line
into the main body of
the cutting head in
accordance with the
arrows on the main
body. Insert enough
line so that approx. 20
mm of the cutting line
protrudes from the
opening on the
opposite side.
Make sure that the
cutting teeth are
correctly aligned in the
direction of rotation.
Various washers are
supplied with the
cutting head.
For installation on this
type of brushcutter, use
exactly the washer
dimensions shown in
the illustration (outer
diameter, inner
diameter).
The lower washer with
an inner diameter of 16
mm must be positioned
around the splines on
the shaft.
Block the shaft with the pin (29) and tighten the nut
(28). Check that the cutting head is securely seated
and properly centred.
Fit the cover of the
cutting head in place,
turn it in the direction of
the arrow and tighten it
with the combination
wrench as shown in the
illustration until it
engages.
When using the "Jet-Fit-Flexiblade" cutting head,
always use the standard guard and the assembled
protective bar.
Cutting lines must not touch the guard during rotation.
If necessary, insert the cutting lines slightly further
into the main body of the cutting head. The line
trimmer which is assembled in the protective bar is
not suitable for cutting lines. The length of the
cutting lines needs to be manually adjusted to the
correct length.
To replace a cutting
line, pull the
protruding end back
out from the main
body in the direction
of the arrow (use
universal pliers if
necessary).
Fig. 7
Fig. 8c
Fig. 8b
Fig. 8d
Fig. 8e
Fig. 8a
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko AL-KO 137 SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko AL-KO 137 SB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info