594592
29
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
Preparing the equipment for use
ENGLISH 9
4.2 Cutter installation
Always switch off the engine, pull the spark plug cap
and wear protective gloves when fitting or replacing
the cutter!
Depending on your particular model, one of the
following cutting tools will already be provided as
standard equipment with your brushcutter. The
cutting tools described below are available as
genuine SOLO replacement parts which can be
obtained from specialist retailers and should be
installed as described below. Please refer to the
overview of approved accessories in chapter 9 for
more information.
A) Assembly of the 3-tooth brush cutting blade
and the 4-tooth grass cutting blade
Position the brushcutter with the output shaft
facing upwards.
Place the brush cutting blade on the pressure
piece (25). In order to centre the cutting blade, the
shoulder of the pressure piece must be located
exactly in the bore of the cutting blade.
Fix the pressure washer (26).
Place the nut protector (27) and turn safety nut
(28) onto the shaft.
Caution! Left hand thread - tighten counter
clockwise.
Take care that all parts are centered.
Block the shaft with the stop pin (4) and tighten
nut.
It is imperative that the safety nut (28) is
replaced, if it has become loose due to
frequent rem oval and tightening.
Afterwards check that the cutting blade is securely
seated and that it is properly centred.
Transport protection for metal cutting blades
When you first purchase an approved metal cutting
blade which is not supplied together with the
brushcutter (see chapter 9 "Accessories"), you will
also need to purchase a corresponding transport
protector.
When the metal cutting blades are attached (4-tooth
grass cutting blade or 3-tooth brush cutting blade,
provided either as standard equipment with the
different models or purchased as accessories), the
transport protector must always be attached to cover
the blades when the device is being stored or
transported, or during work breaks during which the
engine is switched off.
Position the transport protector with the
corresponding recess at one of the tips of the
metal cutting blade.
Press the two tabs (a) on the transport protector
together to increase the internal diameter of the
transport protector.
Lay the transport protector right over the cutting
tool. Position the inner shoulder (b) between the
metal cutting blade and the running disc.
Open the two tabs again, and in doing so also
position the inner shoulder between the metal
cutting tool and the running disc at tab (c).
When restarting work, take the transport protector
back off by pressing the two tabs (a) together before
starting the engine.
Fig. 5
Fig. 6
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko AL-KO 137 SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko AL-KO 137 SB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info