587610
71
Verklein
Vergroot
Pagina terug
1/184
Pagina verder
71
EN
IMDCFJ. 12.05 6343841_03
Code
Alarm
Code
Pre-alarm
Causes Notes
12 112 High pressure
This signal occurs when the transducer detects a flow pressure
over the set-factory parameter threshold (8) (default: 40 bar).
The pre-alarm state is exited with set_factory (8) – set_factory (b)
pressure (default 40 – 2 = 38 bar)
13 113 No defrosting probe
This signal occurs when the defrosting probe is absent and the
machine is set as heat pump
14 114
Intake pressure transducer
no compressor
This signal occurs when the compressor intake transducer is
absent and the machine is set as heat pump
15 115 Low pressure
This signal occurs when the compressor flow transducer indicates
an intake pressure below the threshold set by the set_factory (9)
parameter in cooling mode (default 4 bar), set_factory(A) ion heat-
ing mode (default 2 bar). The pre-alarm state is exited when the
intake pressure exceeds the intervention set_factory(b) threshold
default equal to 2 bar. The low pressure alarm is suspended in
heating mode for a period of time equal to 3' (set_factory param-
eter (H parameter) from compressor switch on. It is permanently
suspended during cycle reverse
16 - Low performance
Every time the machine is powered, the control checks compres-
sor behaviour once via the yield control procedure (see 8.1); this
control is disabled from dip switch
17 117 Pump magnet circuit breaker
This signal intervenes if the magnet circuit breaker switch protect-
ing the pump is opened. MTP (table 2, contact ID3, clamps M7.5
– M7.6, normally closed). This code is displayed only if the board
is used as a board spare part with SW up to version 3.6.
18 118 High pressure partialisation
This signal occurs every time a partialisation takes place due to
the threshold mentioned in paragraph 8.5 being reached. The
machine blocks in alarm mode when the maximum number of par-
tialisation interventions allowed (expressed by the set_factory (5)
parameter: default 5) is exceeded. With inverter machine mode, it
also indicates a partialisation due to high compression ratio.
19 119 Low pressure partialisation
This signal occurs every time a low pressure partialisation takes
place, par. 8.5. The machine blocks in alarm mode when the maxi-
mum number of partialisations allowed (expressed by the set_fac-
tory (5) parameter: default 5) is exceeded.
20 120 Pressing line temperature partialisation
This signal occurs every time a pressing line temperature par-
tialisation takes place (par. 8.5), the machine blocks in alarm
mode when the maximum number of partialisation interventions
(expressed by the set_factory (5) parameter: default 5) permitted
is exceeded.
21 121 Bemf error
Error in detection of the back emf. This error is returned by the
inverter control board and is linked to compressor peak problems
(longertek 4 code or longertek 20 code)
22 122 Internal communication error
The inverter control board has internal communication problems
(longertek 5 code)
23 123 Over-current
Excess current absorption by compressor (longertek 6 code)
24 124 No load
The compressor does not absorb enough current, it may
turn in idle mode (longertek 7 code)
25 125 Incorrect voltage
The inverter control board indicates incorrect bus voltage
(longertek 8 code)
26 126 Error on start-up
The inverter control board indicates incorrect start-up of
the PMSM motor (longertek code 9)
27 127 IPM protection error Error on the IGBT (longertek 12 code)
28 128 EEPROM error
Eeprom error on the inverter control board (longertek 13
code)
29 129 Compressor stall Code longertek 16
30 130 No communication
The inverter control board does not respond. It may not be
powered or the serial cable could be disconnected or the
A and B signals reversed
31 131 PFC Module PFC inverter module error (longertek 23 code)
32 132
Cooling fin overheating
(code APY 1)
33 133 Over current in acceleration mode Hardware error (cod. APY 2)
34 134 Over-current at constant speed Hardware error (cod. APY 3)
35 135 Over current in deceleration mode Hardware error (cod. APY 4)
36 136 Under-voltage on the DC Bus (code APY 5)
71

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aermec MODUCONTROL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aermec MODUCONTROL in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info