801481
6
Verklein
Vergroot
Pagina terug
1/25
Pagina verder
ENGLISH
UNO G8 Series | User manual
10
11
User manual | UNO G8 Series
Series
3.2 | BELTPACK TRANSMITTER SETUP
LCD main window shows GROUP, CHANNEL and MUTE settings as well
as battery status. To proceed with the adjustments, please use SELECT
and MUTE buttons.
To proceed with the adjustments, please use SET and up/down buttons.
GROUP SELECTION
Press the SELECT button until when “GROUP” starts flashing in LCD.
Use the same button to select the desired group of frequency, then wait
for steadily lit icon to conrm the choice.
CHANNEL SELECTION - MANUAL SETUP
Press for 2” the SELECT button until when “CHANNEL” starts flashing
in LCD. Use the same button to select the desired channel, then wait
for steadily lit icon to conrm the choice. Simultaneously using multiple
systems, it is preferable to have them on the same frequency band but
on different channels.
MUTE
Press the MUTE button to activate or deactivate this function.
MUTE ON setting allow to mute signal transmission toward the
receiver. When MUTE is activated, its icon is shown in the lower left
corner and the bi-color ASC/LOW BATT LED switches to red.
3.3 | TIPS FOR BETTER USE OF THE SYSTEM
To achieve the best reception, please place the receiver at least 1 m high
with the antennas pointing upward, in V shape. Please, make sure the
receiver and transmitter must have a direct “visual contact”, i.e. with no
halfway obstacles and allowing a minimum 50 cm distance between
receiver antennas and any metallic object.
Don’t place the receivers too close to digital control devices.
CHANNEL SELECTION - MANUAL SETUP
Press the SET button until when “CHANNEL” starts flashing in LCD.
Use the up / down buttons to select the desired channel then press again SET
to scroll following parameters and confirm the choice. Simultaneously using
multiple systems, it is preferable to have them on the same frequency band but
on different channels.
CHANNEL SELECTION - ASC
Press the SET button until when “CHANNEL - AUTO” starts flashing in LCD.
Use the up/down buttons to start the automatic channel scan, after searching the
receiver will set automatically the channel without interference. If the automatic
scanning is not successful, please repeat it until you nd a free frequency.
SQUELCH SETTING
Press the SET button until when “SQL” starts flashing in LCD.
Use the up/down buttons to select three different noise suppression settings.
L: lower value
M: intermediate value
H: high value
Starting a new session, always set the receiver on lower squelch value and gradually
raise the value in case of interferences. In critical conditions of the radio-reception,
H setting may reduce the signal transmission distance to the receivers.
VOLUME SETTING
Use the up/down buttons to select volume level from 0 to 63.
ATTENTION: during the rst powering, set the level to the minimum to allow various
settings, in particular that of SQL function.
LOCK ON/OFF
The lock function is automatically activated after about 20” of device idle.
Press the SET key for 2” to turn off the lock and activate again the receiver.
ATTENTION: when the LOCK icon is shown , you can still see the unit settings,
but these settings are not editable.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ANT Uno G8 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ANT Uno G8 in de taal/talen: Duits, Engels, Italiaans als bijlage per email.

De handleiding is 3.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info