English
31
15 Speakers
16 Battery compartment
17 LCD display
Rear side (not shown)
Power cord
Wire antenna
Sub-structure assembly instructions
If you don’t want to use the device as a standalone appliance,
then please assemble it as follows:
• Removeallobjectsfromthecupboardandanything
which is fragile in the adjacent cupboards.
• Fortheinstallationthecupboardmustfullthefollowing
conditions:
Thicknessofthecupboardoor
between 16 mm and 20 mm.
• Thewallmountingofthecupboardmustbestableand
anchored firmly in the wall with at least 2 screws.
• Important! Do not install the device above a cooker!
• Wheninstallingthedeviceitmustbeensuredthatthere
is a power socket within reach.
• Themainssocketmustbewithineasyreach,sothatthe
plug can be quickly removed in an emergency.
• Important! Do not connect the device to the mains
power supply until after installation!
• Thedevicecannotbeinstalledundercupboardsunder
which there is a lighting strip.
• Formounting,youmayneedthefollowingsupplies:
Reamer or nail, screwdriver, measuring tape, adhesive
tape, scissors, safety goggles.
Supplied mounting accessories
4 Screws (if necessary, check the battery compartment)
1 Drilling template
CAUTION:
• Pleaseadheretothedimensionsstatedintheinstalla-
tion instructions.
• Youshoulduseonlytheinstallationaccessoriessup-
plied.
Installation
• Stickthetemplatetothebottomofthewallcabinetwith
adhesive tape. With the help of a gimlet or nail pierce the
crosses at the attachment points and use it to mark the
holes.
• Removethemountingplate(2)fromthedevice.Todoso,
firmly press the mounting plate backwards.
• Removethetemplateandtthemountingplatewiththe
4 screws below the cabinet.
CAUTION:
• Useascrewdriverandnotacordlessscrewdriver.
• Ifyouusedifferentscrewsorifthethicknessofthe
cabinetooristoosmall,thescrewsmaypushthrough
thecabinetoor.
• Nowhangtheradioontothemountingplateandpushit
backwards until it clicks into place.
Start-up of the device / Introduction
• Readtheoperatinginstructionsthoroughlybeforethe
start-up!
• Ifapplicable,removetheprotectivelmfromthedisplay.
Location
• Foldoutthestands(14).
• Selectasuitablelocationforthedevice.Suitablewould
be an even, non-slip surface on which you can easily
operate the device.
• Ensurethatthedeviceisadequatelyventilated.
Inserting the power reserve batteries
(Batteries not included)
In case of a power failure or if the power plug of the device
is disconnected from the outlet, then the settings will be
retained if the power reserve batteries have been inserted.
1. Open the battery compartment on the bottom.
2. Insert 2 AA/R6 1.5 V type batteries. Pay attention to the
correct polarity (see bottom of battery compartment)!
3. Close the battery compartment again.
4. If the device is not used for a long period of time, then
remove the batteries from the device to prevent the bat-
tery acid from leaking.
WARNING:
Thebatteriesshallnotbeexposedtoexcessiveheatsuch
as sunshine, fire or the like. Danger of explosion!
CAUTION:
• Differentbatterytypesornewandusedbatteriesmay
not be used together.
• Batteriesdonotbelonginthehouseholdwaste.
Dispose of spent batteries at the designated collection
points or at the dealer.
Power supply
• Inserttheplugintoaproperlyinstalled230V,50Hzpower
socket. 1- 1 0:00 will appear on the display. Please ensure
that the mains voltage corresponds to the information on
the type plate.
• Ifyouhavenotinsertedanypowerreservebatteries,the
preset time and radio stations are lost as soon as the
power supply has been interrupted.