76
ENGLISH
Settings
Adjust the volume
WARNING:
Setting the volume too high may damage your
hearing!
If the volume is set too high your hearing may be
permanently damaged.
Set the volume to a reasonable level.
►
Turn the multijog (3) to set the volume.
Switch unit to mute
Press the
PWR/MUTE button (2) to switch the unit to
mute.
Press the
PWR/MUTE button (2) again to deactivate
the function.
Sound settings
Press the multijog (3). The current volume is displayed.
Press the multijog each time to select the next option.
The following settings are available:
VOL - Volume (from 0 to 100),
BAS - Bass (from -10 to +10)
TRB - Treble (from -10 to +10)
BAL - Balance (Sound balance between the right and
left speaker) (from 10L to 10R)
FAD - Fader (Sound balance between the rear and
front speaker) (from 10F to 10R)
DSP - Equalizer (Digital Sound Processing) (FLAT, CLAS-
SICS, POP M, ROCK M, DSP OFF)
Turn the multijog to adjust the displayed setting.
More settings via the multijog
Keep the multijog (3) pressed for a few seconds to
access more settings options. Press the multijog each
time to select the next option.
Turn the multijog to adjust the displayed setting.
The following settings are available:
TA
Trac announcement settings
TA SEEK
■
: If the TA function is activated,
the unit will try to select a station which is
broadcasting trac information.
TA ALARM:
■
The station is not automati-
cally preset. If no trac information is
received a buzzer sounds and NO TP/TA is
shown on the display If the selected
station is not transmitting a RDS-Signal,
SEEK PI is shown n the display.
PI
If you are driving through an area in which
two stations with the same AF- but dierent
PI-Code (PI = Programme information) – can
be received, the reception will then become
instable. In this situation you have a choice
between:
PI SOUND:
■
If the unit switches over in any
case to the other station, the sound from
the other station will only be heard for less
than one second.
PI MUTE:
■
The sound of the other station is
suppressed.
RETUNE
Time frame for automatic tuning into trac
information or program information:
S
■
(Short) after around. 30 seconds
L
■
(Long) after around 90 seconds
MASK
This option decides which stations should be
excluded from the station scan:
DPI:
■
Alternative frequencies with dierent
PI-Code are excluded from the scan.
ALL:
■
Alternative frequencies with dier-
ent PI-Code and without RDS-Information
with high signal levels are excluded.
TA VOL
Trac information volume
EON TA
The unit can receive RDS EON data. EON
means the transmission of additional station
information within a station group. In the
event of a trac announcement (TA) it will
switch within a station group from a non-
trac broadcast to the corresponding trac
radio station of the station group.
DX:
■
the unit attempts to receive the EON
TA information from a station within range
and thus to improve the reception quality.
LO:
■
Prevents switching over to a station
with too weak a signal level.
BEEP
Sound heard when a button is pressed:
BEEP 2ND:
■
Unit beeps when a button with
multiple functions is kept pressed.
BEEP ALL:
■
A beep sounds whenever a
button is pressed
BEEP OFF:
■
no beep
Stereo/
Mono
Switch between Stereo and Mono
Loudness
The bass is amplied when the Loudness
function is activated.
LOUD ON:
■
Loudness function is
activated.
LOUD OFF:
■
Loudness function is
deactivated.
DX/LOCAL
Switches between local and more distant
stations.
DX:
■
Receive other more distant stations.
LOCAL:
■
Receive local stations.
Show Display information
Press the
DIS (40) button several times to display the
following information on the display in sequence:
