654495
26
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
3M IPC 2000 3M
Multimedia Projector MP8760 21
ENGLISH
The Standby button
blinks red and the
lamp with not turn
on.
There is no lamp in
the unit.
The lamp is
improperly placed in
the unit.
Put a 3M MP8760 lamp in the unit.
Install the lamp again.
A question mark
appears in the lower
left of the screen
when connecting to
computer video.
The horizontal and
vertical
synchronization
signals from the
computer video are
not correctly polarized
according to VESA
video standards.
The computer video
signal is not a VESA
or Mac standard.
Select Mode in the Image menu, select the correct video
mode, and press Enter.
Image off-center. Image position. Center image with the Disc Pad of the control panel or on the
remote control transmitter.
Cannot get entire
image on the screen.
Wrong Tracking
value.
Compatibility
problem.
If vertical interference stripes occur, change the Tracking
value in the Picture menu for optimum performance.
Refer to the documentation for your graphic card. Change the
Resolution setting in the Picture menu to the resolution of
the video mode output from the computer graphic card.
Washed out image. Wrong Contrast
setting.
Wrong Brightness
setting.
Change Contrast setting in the Picture menu. The bar
should be in the middle position.
Lower Brightness setting in the Picture menu. Choosing
Brightness and pressing Enter can perform an automatic
adjustment.
Humming noise.
Slowly passing
horizontal bars.
Signal sources are
connected to different
power sources.
VCR connected to
aerial system and to
projector.
Bad signal.
Locate the source of disturbance. Disconnect the sources
one after another from the projector. Connect all sources to a
common power source.
Remove antenna connection from VCR. If the disturbance
disappears, use a by-pass filter (isolating transformer) to
connect the antenna to the VCR.
Try different input source.
Image is disturbed or
unstable.
Wrong Sync setting.
Wrong Tracking
value.
Set to factory default setting. (See below!)
Change Sync setting in the Picture menu for optimum
performance
For vertical interference stripes, change the Tracking in the
Picture menu for optimum performance.
No computer image
projected. Message
Looking for signal
... displays.
Loose cable.
No power to
computer.
Wrong synchro-
nization mode.
Check and secure cable connections.
Turn on computer.
Adjust synchronization mode of the projector to the synchro-
nization mode of the computer via Advanced Setup menu.
No video image
projected.
Loose cable.
No signal from video
source.
Check and secure cable connections.
Check video picture on TV.
Mouse does not
work.
Loose cable.
Wrong connection.
Wrong power up
sequence.
Check and secure cable connections.
For PS/2 and ADB (Apple) mouse a special adapter is
necessary. Only use adapters from the original manufacturer
(Section 8-2).
The mouse emulation operates correctly only if the correct
power up sequence has been used (refer to section 3-5.)
Image off-center. Image position. Center image with the Disc Pad of the control panel or on the
remote control transmitter.
Cannot get entire
image on the screen.
Wrong Tracking
value.
Compatibility
problem.
If vertical interference stripes occur, change the Tracking
value in the Picture menu for optimum performance.
Refer to the documentation for your graphic card. Change the
Resolution setting in the Picture menu to the resolution of
the video mode output from the computer graphic card.
Washed out image. Wrong Contrast
setting.
Wrong Brightness
setting.
Change Contrast setting in the Picture menu. The bar
should be in the middle position.
Lower Brightness setting in the Picture menu. Choosing
Brightness and pressing Enter can perform an automatic
adjustment.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw 3m MP8760 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van 3m MP8760 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van 3m MP8760

3m MP8760 Gebruiksaanwijzing - Deutsch - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info