654495
25
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
20 3M
Multimedia Projector MP8760 3M IPC 2000
ENGLISH
Section 7: Troubleshooting
7-1. Troubleshooting Problems and Solutions
Problem Probable Cause Possible Solution
Projector will not turn
on.
Power cable is
disconnected or not
plugged in.
Main power switch is
not on.
The ?inner fuses? are
open?
Plug the power cable into an AC outlet.
Turn the main power switch to the ON postion.
Send the unit to be repaired.
Image is disturbed or
unstable.
Wrong Sync setting.
Wrong Tracking
value.
Set to factory default setting. (See below!)
Change Sync setting in the Picture menu for optimum
performance
For vertical interference stripes, change the Tracking in the
Picture menu for optimum performance.
No computer image
projected. Message
Looking for signal
... displays.
Loose cable.
No power to
computer.
Wrong synchro-
nization mode.
Check and secure cable connections.
Turn on computer.
Adjust synchronization mode of the projector to the synchro-
nization mode of the computer via Advanced Setup menu.
No video image
projected.
Loose cable.
No signal from video
source.
Check and secure cable connections.
Check video picture on TV.
No video images are
projected or the
video image ?does
something? and
turns off.
The video source is
sending a video
signal and the
projector cannot
automatically select
the video standard in
use.
In the submenu Video Standard? in the Advanced Setup
menu, manually change the video standard from Automatic to
the type of standard in use.
Mouse does not
work.
Loose cable.
Wrong connection.
Wrong power up
sequence.
Check and secure cable connections.
For PS/2 and ADB (Apple) mouse a special adapter is
necessary. Only use adapters from the original manufacturer
(Section 8-2).
The mouse emulation operates correctly only if the correct
power up sequence has been used (refer to section 3-5.) To
verify that the projector is programmed for the desired mouse
emulation mode, go to the Screen Parameters? In the
Advanced Setup/Test submenu. Check that the parameter
MTPE presents the desired mouse mode. This is not a
selection, but a ???? that shows the type of mouse emulation
with which the projector is programmed to communicate.
The lamp turns off,
the Standby button
and LED lights up
and stays green as
the fan cools the
unit, and the unit
goes into Standby
Mode.
The air intake or
exhaust vents are
blocked.
The air filter is dirty.
Clear all obstructions from the air intake and exhaust vents.
Clean or replace the filter.
The lamp turns off,
the unit goes into
Standby Mode, and
the fan ????s more
rapidly.
The air intake or
exhaust vents are
blocked.
The air filter is dirty.
Clear all obstructions from the air intake and exhaust vents.
Clean or replace the filter.
Note: It is necessary to turn the projector off and on with the main power switch before restarting the projector.
The lamp turns off,
the Standby button
blinks red for a few
seconds, and the
unit goes into
Standby Mode.
The air intake or
exhaust vents are
blocked.
The air filter is dirty.
Clear all obstructions from the air intake and exhaust vents.
Clean or replace the filter.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw 3m MP8760 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van 3m MP8760 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van 3m MP8760

3m MP8760 Gebruiksaanwijzing - Deutsch - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info