Handleiding master AC 1600 E (pagina 26 van 64) (Duits, Engels, Italiaans, Pools, Deens)

588460

Verklein

Vergroot

Pagina terug

1/64

Pagina verder

4. The unit will shut down automatically after the SLEEP

function running for 12 hours.

5. Please note, the sleep function is not available while the

machine is working in ventilation. Only available in

Cooling or Heating mode.

6. When the machine is in Sleep function, the ventilation

would turn to be LOW.

Heating function (This is optional, only for cool & heat

model.)

1. When using Heat Pump, the ambient warm air is recycled

and use to heat the area where it is required. The Exhaust

Pipe must be fitted firmly to allow the cold air to be

removed outside.

3. Continuous drain is compulsory while the unit is in heat

mode. Working range for heating function is 5 to 27oC.

For temperature outside this range, the unit may not work

properly.

TiO2 / Ionizer function (option)

1. This is only for the model with TiO2 or Ionizer function,

i.e. model no. with T or I. T stands for TiO2 (ultra-violet)

, I stands for Ionizer.

2. To start the TiO2 or Ionizer button, please press

TiO2/Ionizer button. These two functions can clean the air,

improve the air quality.

Regulating air flow direction

Adjust the air louvers by hand to control the air flow direction.

(Fig. 23)

Self-diagnosis

This machine is equipped with self-diagnosis function. If

something is wrong in the machine, the display window will show

the word “E1” or “E2”. As this time, please call your service

centre.

All the above functions can also be performed with the supplied

remote control. (Fig. 24)

This remote control requires one button cell (No.CR2025) to

operate

NOTICE !

1. To prolong the compressor's life, after switch-off of the

unit, please wait for 3 minutes (at least) before re-switch.

2. The cooling system will switch off if the ambient

temperature is lower than the set one. The ventilation,

however, keeps working on the set level. If the ambient

temperature rises above the selected level, the cooling will

return to work.

3. On the contrary, the heating will switch off if the ambient

temperature is higher than the set one (still, the ventilation

keeps working on the set level). As the ambient

temperature drops below the selected level, the heating

will return to work.

4. This machine is equipped with ANTI-FROST function.

While using the heating function during low temperature,

sometimes the heating will stop for a while in order to melt

the frost. As this occurs, just wait for the heating returns

to work.

DRAINAGE

During the process of cooling, some water will be extracted from

the air into the unit. If the tank is full, both of the compressor and

motor will stop. The “water full” sign will light on, also the

machine will beep as reminder.

To make the cooling work again, please empty the water by one of

the following ways:

Fig. 25

1. Turn off the air conditioner and avoid moving it when full.

2. Position a container (a water tray for example) underneath

the drain hole.

3. Remove the drain knob & rubber plug from the drain hole

and allow the water to drain out.

4. When the container is almost full, replace the rubber plug

in the drain hole and empty the water tray.

5. Repeat until the unit is emptied.

6. Replace the rubber plug and tighten the drain knob firmly.

7. Switch on the unit - the full water or compressor operating

indicator should not be flashing.

If you wish to operate the unit without the need to empty the water

tank, please:

Fig 26.

 Remove the drain knob and rubber plug and retain for

future use.

 Connect the drain tube supplied to the water outlet as

shown and locate the other end into a drain.

Fig. 27.

 The drain tube may be extended by adding an extension

tube and using a suitable connector.

Please note (Fig. 28.)

1. The drain must be at or below the outlet level.

2. Flashing comp / ‘full water’ indicator will not function in

this mode of drainage.

3. If you want to extend the water tube, you can connect it

with another tube (OD: 18mm)

Special caution for heating function !(fig. 29)

While using the heating function, please note:

1. Install the exhaust pipe well, in order to exhaust the cool

air to outdoor. (Please refer to the instruction manual for

installation method.)

2. Fix the drainage to be continuous one (i.e. drain the water

by water tube).

3. Working range for heating function is 7 to 27oC (for

cooling function, it is 18 to 32oC). For temperature outside

this range, the unit may not work properly.

MAINTENANCE

Always unplug the air conditioner from the mains before

cleaning. To maximize the efficiency of the air conditioner

clean regularly.

Cleaning the housing

Use a soft, damp cloth to wipe the body clean.

Never use aggressive chemicals, gasoline, detergents, chemically

treated cloths, or other cleansing solutions. These all could

possibly hurt the cabinet.

Cleaning the filter

Use a vacuum cleaner or tap the filter lightly to remove loose dust

and dirt from the filters and then rinse thoroughly under running

water (no hotter than 40oC).

Dry thoroughly before replacing.

Notice! Never operate the unit without the filters.

End of season storage (fig. 30)

 Drain any water in the unit before completely operating the

unit on ventilation only mode for a few hours, to

thoroughly dry the inside.

 Clean or change the filter

 Unplug and store the power cord as shown

 Cover the cord storage

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

master AC 1600 E Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info