728823
21
Verklein
Vergroot
Pagina terug
1/168
Pagina verder
4
9
E CLEAN START
Clean start function reduces the odor emitted by the heater at the ignition
significantly. It takes one or two more minutes to ignite than normal mode.
By pressing the clean start key K while the heater is off, the indication
is lit and
change to clean start mode.
Once the key is pressed again, the mode will turn off and return to the normal
ignition mode.
F IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Alays ignite the heater ith the
button
. Never use matches or a
cigarette lighter.
Just press the button to ignite the heater. The POWE lamp ill start blinking,
indicating that the ignition procedure has started. This will take a short while.
Once the heater is burning, the POWE lamp ill remain lit (red). The information
display will show two numbers. The light next to them indicates that these
numbers refer to the temperatures (ig. ). The actual room temperature is
indicated belo OOM, hile the temperature setting is indicated belo SET. The
latter can be changed with the adjustment keys (refer to Section G).
Prior to igniting the heater, alays check for sufficient fuel in the removable tank.
G SETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, hen the heater is burning. Use
the adjustment keys to adjust the temperature. irst press either of the to
keys to switch on the function (the °C mark will start blinking). Next, adjust the
temperature using the key on the right (min.) to set the temperature to a higher
setting and the key on the left (hour) to loer the temperature. Press once to
increase the value one step. After approimately 10 seconds the C mark ill stop
blinking and the setting ill be locked (ig. ).
The available temperature settings range from C minimum to 28C maimum.
When the heater has been unplugged (or after a power failure), the temperature
will reset to the factory setting of 20°C.
H SWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1
Press the
button . The information display will show the CLOCK
signal. Within approximately one minute the flame will have extinguished.
2
Press the TIME key , when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function.
G: The required tempe-
rature on the left, the
measured temperature
on the right.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Zibro-LC-135

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zibro LC 135 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zibro LC 135 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info