781890
18
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
18 І 24
Warning! This electric tool generates an electromag-
netic eld du ring operation which may impair active or
passive medical implants under certain circumstances.
ln order to reduce the risk of severe or Iethal injury, we
recommend that persons with medical implants consult
their doctor and the manufacturer of the medical implant
before using the power tool.
Tool description and scope of delivery
Tool description (Fig.1)
The tool description refers to the illustration at the begin-
ning of this instruction manual.
1. Handle surface
2. Main handle
3. On/off switch
4. Adapter with connecting nut
5 Powercord
6. Adjustment wheel for speed pre-selection
7. Ventilation opening
8. Flexible grinding head
9. Grinding plate
10. Brush edge
11. Extraction hose
12. Hoseadapter
13. Abrasive sheet
14. LED-Light
Scope of delivery (Fig.1)
1 drywall sander
1 extraction hose (1 1)
2 hose adaptor (1 2)
6 abrasive sheets (1 3) (different grain sizes)
Before start-up
unpacking
1. Open the packaging and carefully takeout the power
tool.
2. Remave the packaging material as weil as the pack-
aging I transport Iacks (if any).
3. Check the scope of delivery for completeness and
check the power tool and the accessory parts for
transport damage.
Note: Do not start the power tool if you notice that parts
are missing or damaged. Contact the retailer where you
purchased this power tool.
4. Store the packaging until the end of the warranty pe-
riod, if possible. Piease dispose ofthe packaging in
accordance with environmental regulations and take
it to a recycling depot.
WARNING!
Neither power tools nor packaging materials are
toys! Children must not play with plastic bags, foils
and small parts! Danger of swallowing and suffo-
cation!
Installation
- Fold the front and back parttagether (Fig.2). And then
tighten the screw nut. (Fig.3).
- The Iongest length installation Insert the additional han-
dle to the end of the machine. And then turn the screw
nut on the end ofthe machine for tightening. (Fig.4)
c) Keep your body away from the area where the
power tool may move in the event of a kickback.
Kickbacks always move the power tool in opposite
direction to the movement of the grinding disk at the
spot where it blocks.
d) Corners, sharp edges, etc. must be processed
with special care. Make sure that the insertion tool
does not bounce back from or get trapped on the work
piece. The rotating insertion tool tends to jam in cor-
ners, at sharp edges or when it bounces back. This
may cause the loss of control or a kickback.
e) Do not use chain rings or toothed saw blades.
These insertion tools frequently cause kickbacks or
the loss of control of your power tool.
Additional safety notes regarding grinding with
sandpaper- Special safety notes regarding grinding
with sandpaper
a) Do not use oversized abrasive sheets; always ob-
serve the manufacturer‘s specications for abra-
sive sheet dimensions. Abrasive sheets protruding
the grinding plate may cause injury or result in the
blocking or tearing apart of the abrasive sheet or in
kickbacks.
Additional safety notes
a) Connect a vacuum cleaner to the supplied adapter
before starting your operations.
b) Attention! Keep away grinding dust from open Iire.
Dust may be explosive.
c) Always wear goggles and a dust mask when grinding,
in particular du ring overhead work and when process-
ing critical materials! When grinding certain materi-
als (e .g.lead paint, certain types of wood and metaI)
harmful or noxious dust may be generated. Touching
or breathing in such dust may imply risks for the op-
erator or people in the vicinity.
Notes regarding vibration and noise emissions
Reduce noise emissions and vibrations to a minimum!
1. Only use power tools which are free of defects.
2. Maintain and clean the power tool on a regular basis.
3. Adjust your way of working to the power tool.
4. Do not overload your power tool.
5.Have your power tool inspected, if necessary.
6. Switch off the power tool when it is not in use.
Remaining risks
Even if you use this power tool in compliance with the
regulations, there arestill remaining risks. The follow-
ing risks may occur due to the type and design of the
power tool:
a) Damage caused to your health resulting from hand/arm
vibrations if the power tool is used over a Ionger period
of time or if it is not properly used and maintained.
b) lnjury and damage to property caused by ying off inser-
tion tools which are unexpectedly expelled from the power
tool due to sudden damage, wear or incorrect insertion.
c) Burns and cuts if the insertion tools are touched di-
rectly after use and/or with your bare hands.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zgonc YPL 710 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zgonc YPL 710 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2.6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info