Handleiding Zelmer 882.3 (pagina 45 van 50) (Engels, Pools)

540077

Verklein

Vergroot

Pagina terug

1/50

Pagina verder

II. Liquidizer

a) cup/dispenser,

b) lid,

c) gasket,

d) liquidizer container.

How to use the accessories

Food processor blade – is used to process meat, mix

dough and other functions.

Slicing disc – is used to cut fruits and vegeta-bles into thin

and thick slices.

Shredding disc – is used to shred fruits and vegetables into

ne or coarse shreds.

French fry slicing disc – is used to cut pota-toes for French

fries.

Pureeing disc – is used to pulp fruits and vegeta-bles.

Disc driver – is used to install changeable discs.

Food pusher, dispenser – is used to push ingredients that

are grinded by the slicing discs, to dispense loose or liquid

ingredients and to close the feed tube of the lid. A small

opening at the bottom of the food pusher allows to evenly

dispense liquids (e.g. oil while preparing may-onnaise).

Liquidizer – is used to prepare food of liquid or semi-liquid

consistency such as: soups, creams, sauces, cocktails and

others.

Slicing and shredding discs are round, with two-sided blades

(one side for thin slices, the other for thick slices).

Preparation for operation, start-up and

operation

Wash the parts that have contact with the processed

●

food before initial use.

Place the motor on a hard, clean and dry surface near

●

the electrical outlet.

Unwind a sufcient length of the cord. The remaining

●

cord can be stored in the housing. Put the remaining

cord in the housing through the opening at the back of

the housing.

Choose the appropriate attachments depend-ing on the

●

selected type of operation.

Operating the food processor

Place the food processor container on the fastening hooks

of the motor so that the sign on the container is

opposite the sign on the housing and turn the container

counterclockwise until the fastening hooks snap shut

(position ).

Operating the food processor blade (g. 2a)

Put the blade in the casing on a hard surface (put in on

●

the casing).

Press the blade and remove the casing by pulling it

●

upwards.

Place the blade in the container so that it is connected to

●

the motor shaft.

Put the ingredients to be processed inside the container

●

according to the selected recipe.

Put the lid on the fastening hooks of the con-tainer so

●

that the sign on the lid is opposite the sign

on the container and turn the lid anticlockwise until the

hooks snap shut (position ).

Put the food pusher into the feed tube of the lid.

●

Plug in the appliance.

●

Set the desired speed using the knob and switch on the

●

appliance - set the switch in the position “1”.

The food processor may also be switched on by

setting the switch in the “pulse” posi-tion.

Operating the slicing disc (Fig. 2b)

Put the selected slicing disc on the hooks of the disc

●

driver so that the blades that are to be used during

operation are on top and turn the disc driver anticlockwise

until stop.

Place the tool in the container so that it is connected to

●

the motor shaft.

Put the lid on the fastening hooks of the container so that

●

the sign on the lid is opposite the sign on the

container and turn the lid anticlockwise until the hooks

snap shut (position ).

Plug in the appliance. Set the desired speed using the

●

knob and switch on the appliance - set the switch in the

position “1”. The food processor may also be switched

on by sliding the switch to the “pulse” position.

The feed tube of the lid is used to add solid and liquid

ingredients to the container. It is divided into two parts

of different sizes. The wide part is for larger products and

the narrow part is for smaller products. Add the processed

products gradually, pushing them slowly and with a steady

thrust down the feed tube with the pusher.

Operating the liquidizer (Fig. 2c)

Put the liquidizer container on the fastening hooks of the –

motor so that the sign on the container is opposite

the sign on the housing and turn the container

anticlockwise until the hooks snap shut (position ).

Put the ingredients to be processed inside the container –

according to the selected recipe.

Make sure the gasket is properly installed in the groove –

by the edge of the lid.

The rectangular protrusion of the gasket is used to –

remove the gasket from the lid.

Put the lid of the liquidizer on the fastening hooks of the –

container so that the sign on the lid is opposite the

sign on the container and turn the lid anticlockwise

until the hooks snap shut (position ).

Press the cup-dispenser into the opening of the lid. –

Plug in the appliance. –

Set the desired speed using the knob and switch on the –

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Zelmer 882.3 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info