539643
91
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
ATTENTION!!! In case of finding out that the nozzle does not spray the water although the
pump is on, check if the back tank is properly assembled (push it strong in),
and assembling the stub in the valve at the base. In case of difficulties with
fitting lubricate the seating of back tank valve and the stub sealing.
Clean the carpet so, that you do not step on the cleaned surface during cleaNing or just after.
ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one of the a/m
cleaning agents only.
After cleaning the part of the carpet make a break and dry it with forward and backward movements
of the nozzle. Repeat the activities until the whole surface of the carpet is dried.
When spraying is finished switch the pump off and press for a moment the button adjusting the
water flow to the nozzle, to release the pressure.
In case of old or especially difficult stains, damp the place with cleaning agent recommended
by ZELMER S.A., up to the moment the foam appear. Then leave for a while and next suck it
out with the vacuum cleaner.
ATTENTION!!! Do not allow the carpet soaking. It can cause the permanent deformation
(rucking).
91
PLAIN FLOORS CLEANING
Fit the brush strip on the nozzle.
Press the pump on/off button in and switch the vacuum cleaner on (as in case of carpets).
Press the adjusting button at the hose handle to adjust the
water flow to the nozzle.
ATTENTION!!! In case the spraying nozzle is blocked disassemble the
nozzle from the tube and clean (blow) the duct, or replace
the nozzle with a new one.
The set of spare nozzles is attached to the accessories
Nozzle exchange
1. Remove the spraying element and the ring ø 5,6 x 1 from the
big (or small) spraying nozzle,
Press the sprayer with your thumb according to the mark on the nozzle housing.
2. Lubricate the new sprayer including the ring and insert it into the nozzle inlet up to the moment
the hooks are locked.
Move the nozzle along the cleaned surface with forward and back ward movements.
Stop the spraying after clearing the part of the floor and suck the solution in, making slow
movements of the nozzle in your direction, until all solution is collected from the floor.
Continua it until all the floor is cleaned and dried.
When spraying is finished switch the pump off and press for a moment the button adjusting the
water flow to the nozzle, to release the pressure.
If you preformed wet clearing (picking up wet dirtiness) before finishing operation in the final
stage, suck in abort 1–2l of clean water in order to flush the tubes and hose, and then suck in
the air for a while, in order to dry them.
AFTER OPERATION
Switch the vacuum cleaner off and unplug it from the mains supply outlet.
Rewind the cord pressing the rewind button. Hold the plug when rewinding, do not
allow the cord to get entangled and the plug to bump the casing.
Turn the ending of the hose up to the position where the tops
marks on the hose ending and tank cover each other and remove
the hose from the tank.
Remove the hose stub from the base.
Press the button and disassemble the tubes.Disassemble the
hose and nozzle similar way.
91

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zelmer 619 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zelmer 619 in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 3,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info