765774
23
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
GETTING
STARTED?
EASY.
User Manual
ZWF845B4PW
EN User Manual
Washing Machine
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
2
staff kitchen areas in shops, offices and other working
environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments;
areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 8 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
3
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
operates. The glass can get hot.
Make sure that all metal objects are removed
from the laundry.
INTERNAL LIGHTING
WARNING! Risk of injury.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
The following spare parts will be available for 10
years after the model has been discontinued:
motor and motor brushes, transmission between
motor and drum, pumps, shock absorbers and
4
springs, washing drum, drum spider and related
ball bearings, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, filters and
aquastops, printed circuit boards, electronic
displays, pressure switches, thermostats and
sensors, software and firmware including reset
software, door, door hinge and seals, other
seals, door locking assembly, plastic peripherals
such as detergent dispensers. Please note that
some of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3
5
6
4
9
6
7
10
8
11 12
1Worktop
2Detergent dispenser
3Control panel
4Door handle
5Rating plate
6Quick Reminder sticker
7Feet for levelling the appliance
8Drain hose
9Inlet hose connection
10 Mains cable
11 Transit bolts
12 Hose support
5
00000000
00A
Mod. xxxxxxxxx
000V ~ 00Hz 0000 W
910000000 00
A
B
C
Prod.No.
D
The rating plate reports the model name (A),
product number (B),electrical ratings (C) and se-
rial number (D).
TECHNICAL DATA
Dimension Width/ Height/ Total depth 59,6 cm /84,7 cm /57,7 cm
Electrical connection Voltage
Overall power
Fuse
Frequency
230-240 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and moisture
ensured by the protective cover, except where the low voltage
equipment has no protection against moisture
IPX4
Water supply pressure
1)
Minimum
Maximum
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Water supply 2) Cold water
Maximum Load Cotton 8 kg
Spin Speed Maximum spin speed 1351 rpm
1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your do-
mestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
INSTALLATION
WARNING! Refer to Safety chapters.
UNPACKING
1. Open the door. Remove all the items from the
drum.
CAUTION! Accessories delivered
with the appliance may vary
depending on the model.
2. Put the packaging element on the floor behind
the appliance and carefully put it down onto its
rear side. Remove the polystyrene protection
from the bottom.
1
2
6
CAUTION! Do not lay washing
machine on its front.
3. Put the appliance back into an upright position.
Remove the power supply cable and the drain
hose from the hose holders.
WARNING! It is possible to see
water flowing from the drain hose.
This is because the washing
machine has been tested at the
factory.
4. Remove the three transit bolts and pull out the
plastic spacers.
5. Put the plastic caps, that you find in the user
manual bag, in the holes.
We recommend that you keep
the packaging and the transit
bolts for any transport of the
appliance.
INFORMATION FOR INSTALLATION
Positioning and levelling
Adjust the appliance correctly to prevent vibration,
noise and movement of the appliance when it
operates.
1. Install the appliance on a flat hard floor. The
appliance must be levelled and stable. Make sure
that the appliance does not touch the wall or other
units and there is air circulation below the
appliance.
2. Loosen or tighten the feet to adjust the level. All
feet must rest firmly on the floor.
WARNING! Do not put cardboard,
wood or equivalent materials below
the appliance feet to adjust the level.
The inlet hose
CAUTION! Make sure there is no
damage to hoses and there are no
leaks from the couplings. Do not use
an extension hose if the inlet hose is
too short. Contact the service centre
for a replacement inlet hose.
1. Connect the water inlet hose to the back of the
appliance.
20º20º
45º45º
2. Position it toward left or right depending on the
positon of the water tap. Make sure that the inlet
hose is not in vertical position.
3. If necessary, loosen the ring nut to set it in the
correct position.
4. Connect the water inlet hose to the cold water
tap with 3/4'' thread.
Water drainage
The drain hose should stay at a height of no less
than 60 cm and not more than 100 cm.
7
You can extend the drain hose to
maximum 400 cm. Contact the
authorised service centre for the other
drain hose and the extension.
It is possible to connect the drain hose in different
ways:
1. Make a U shape with the drain hose and put it
around the plastic hose guide.
2. On the edge of a sink - Fasten the guide to the
water tap or to the wall.
Make sure that the plastic guide
cannot move when the appliance
drains and the drain hose end is not
immersed in the water. There may be a
return of dirty water into the appliance.
3. If the end of the drain hose looks like this (see
the picture), you can push it directly into the stand
pipe.
4. To a stand pipe with vent hole - Insert the drain
hose directly into a drain pipe. Refer to the
illustration.
The end of the drain hose must always
be ventilated , i.e. the inner diameter of
the drain pipe (min. 38 mm - min. 1.5")
must be larger than the external
diameter of the drain hose.
5. Without the plastic hose guide, to a sink spigot-
Put the drain hose in the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain hose makes a loop to
prevent particles going into the appliance from the
sink.
ø16
1
W011
2
Connect the drain hose to the spigot and tighten it
with a clamp. Make sure that the drain hose makes
a loop to prevent particles going into the appliance
from the sink.
6. Position the hose directly to a built-in drain pipe
in the room wall and tighten it with a clamp.
8
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
ELECTRICAL CONNECTION
At the end of installation you can connect the mains
plug to the mains socket.
The rating plate on the inner edge of the appliance
door and the 'Technical Data' chapter indicate the
necessary electrical ratings. Make sure that they are
compatible with the mains power supply.
Check that your domestic electrical installation can
take the maximum load required, also taking into
account any other appliances in use.
Connect the appliance to an earthed socket.
The power supply cable must be easily accessible
after installing the appliance.
For any electrical work required to install this
appliance, contact our Authorised Service Centre.
The manufacturer does not accept any
responsibility for damage or injury through failure to
comply with the above safety precaution.
ACCESSORIES
AVAILABLE IN WWW.ZANUSSI.COM/SHOP
OR FROM AUTHORISED DEALER
Read carefully the instructions supplied with the
accessory.
Only appropriate accessories
approved by ZANUSSI ensure the
safety standards of the appliance. If
unapproved parts are used, any claims
will be invalidated.
FIXING PLATE KIT
If you install the appliance on a plinth that is not an
accessory supplied by ZANUSSI, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
STACKING KIT
The tumble dryer can be stacked on the top of the
washing machine only by using the correct
stacking kit..
WARNING! Do not put the tumble
dryer under the washing machine.
Verify the compatible stacking kit by
checking the depth of your appliances.
9
CONTROL PANEL
SPECIAL FEATURES
Your new washing machine meets all modern
requirements for an effective treatment of laundry
with low water, energy and detergent consumption
and will care for fabrics.
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that fall
off the clothes to be drained out with the water, in
such a way that there is no need to access this
area for regular maintenance and cleaning. Refer to
chapter 'Care and Cleaning' for best maintenance
and care of the appliance.
CONTROL PANEL DESCRIPTION
1 2 3 4
91011
7
6
8
5
1Programme knob
2Spin reduction touchpad
3Temp. touchpad
4Display
5Prewash touchpad
6Easy Iron touchpad
7Night touchpad
8Extra Rinse touchpad
9Start/Pause touchpad
10 Delay Start touchpad
11 FlexiTime touchpad
10
DISPLAY
A B
E D
C
A. The time area:
Programme time.
The alarm codes. Refer to the chapter
“Troubleshooting” for their description.
The level of the FlexiTime .
B. The Delay Start indicator.
C. The Child Lock indicator.
D. The Door Lock indicator:
It is on, you cannot open the door.
It is off, you can open the door.
It flashes, you cannot open the door. Wait
for some minutes until the indicator is off.
E. Washing phase indicators.
: the washing phase
: the rinses phase
: the spin phase
PROGRAMME CHART
Programme
Default temperature
Temperature range
Reference spin
speed
Spin speed
range
Maximum
load
Programme description
(Type of load and level of soiling)
Eco 40-60
40 °C 1)
60 °C - 30 °C2)
1400 rpm
(1400- 800
rpm)
8 kg White cotton and fast-coloured cotton.
Normally soiled items. The energy consumption
decreases and the time of the washing pro-
gramme is extended, ensuring good washing
results.
Cottons
40°C
90°C - Cold
1400 rpm
(1400- 800
rpm)
8 kg White cotton and coloured cotton. Nor-
mally, heavily and lightly soiled items.
Synthetics
40°C
60°C - Cold
1200 rpm
(1200- 800
rpm)
3 kg Synthetic items or mixed fabric items.
Normally soiled items.
Delicates
30°C
40°C - Cold
1200 rpm
(1200- 800
rpm)
2 kg Delicate fabrics such as acrylics, viscose
and mixed fabrics requiring gentler wash-
ing. Normally and lightly soiled items.
Wool
40 °C
40°C - Cold
1200 rpm
(1200- 800
rpm)
1,5 kg Machine washable wool, hand washable
wool and other fabrics with «hand washing»
care symbol3).
Denim
30 °C
40 °C - Cold
800 rpm
(1200 - 800
rpm)
3 kg Special programme for Denim clothing
with delicate washing phase to minimize
colour fading and marks. For better care a
reduced load size is recommended.
11
Programme
Default temperature
Temperature range
Reference spin
speed
Spin speed
range
Maximum
load
Programme description
(Type of load and level of soiling)
Sportswear
30 °C
40°C - Cold
1200 rpm
(1200- 800
rpm)
3 kg Synthetic and delicate items. Lightly soiled
items or items to refresh.
Spin/Drain 1400 rpm
(1400 -800
rpm)
8 kg All fabrics, except woollens and delicate
fabrics. To spin the laundry and to drain the
water in the drum.
Rinse 1400 rpm
(1400- 800
rpm)
8 kg To rinse and spin the laundry. All fabrics, ex-
cept woollens and very delicate fabrics. Re-
duce the spin speed accordingly to the type of
laundry.
Dark Colours
40°C
60°C - Cold
1200 rpm
(1200- 800
rpm)
8 kg Cotton items or mixed fabric items in
dark colours. Normally soiled items.
CleanBoost
60 °C
1400 rpm
(1400- 800
rpm)
8 kg White cotton items. This programme removes
micro-organisms thanks to a washing phase
with the temperature maintained above 60°C
for several minutes. This helps remove germs,
bacteria, micro-organism and particles. An ad-
ditional rinsing phase ensures a proper removal
of detergent residues and pollens/allergenic
items. In this way the wash is more effective.
14min Refresh
30 °C
800 rpm
(800- 800
rpm)
1,5 kg Synthetic and mixed fabric items. Very
light soiling and items to freshen up.
30min Rapid 4)
40°C
40°C - 30°C
1200 rpm
(1200- 800
rpm)
3 kg Synthetic and mixed fabric items. Lightly
soiled items.
12
Programme
Default temperature
Temperature range
Reference spin
speed
Spin speed
range
Maximum
load
Programme description
(Type of load and level of soiling)
60min EasyWash
30°C
60°C - 30°C
1400 rpm
(1400- 800
rpm)
5 kg Cotton and fast-coloured synthetic items.
Complete washing programme that, in only 60
minutes, washes the daily soiled laundry inten-
sively and ensures a good washing perform-
ance in a short time.
1) According to Commission Regulation EU 2019/2023, this programme at 40 °C is able to clean normal-
ly soiled cotton laundry declared to be washable at 40 °C or 60 °C, together in the same cycle.
For the reached temperature in the laundry, the programme duration and other data, please
refer to 'Consumption Values' chapter.
The most efficient programmes in terms of energy consumption are generally those that per-
form at lower temperatures and longer duration.
2) Standard programmes for the Energy Label consumption values. According to EU regulation
1061/2010, this programme at 60 °C is the «Standard 60°C cotton programme» and at 30 °C is the
«Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy
and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
3) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
4) With unbalanced small loads such as light synthetic garments mixed with much heavier garments like
sponge, the duration of the programme may increase to execute spin speed properly.
Programme options compatibility
Programme
Spin
FlexiTime
Delay Start
Eco 40-60
Cottons
Synthetics
Delicates
Wool
Denim
13
Programme
Spin
FlexiTime
Delay Start
Sportswear
Spin/Drain
Rinse
Dark Colours
CleanBoost
14min Refresh
30min Rapid
60min EasyWash
Suitable detergents for washing programmes
Programme Universal
powder1)
Liquid Univer-
sal
Liquid for col-
oureds
Delicates
woollens Special
Eco 40-60 -- --
Cottons -- --
Synthetics -- --
Delicates -- -- --
Wool -- -- --
Denim -- --
Sportswear -- --
Dark Colours -- --
CleanBoost -- --
14min Refresh -- -- --
30min Rapid -- -- --
14
Programme Universal
powder1)
Liquid Univer-
sal
Liquid for col-
oureds
Delicates
woollens Special
60min Easy-
Wash -- --
1) At temperature higher than 60 °C the use of powder detergent is recommended.
= Recommended -- = Not recommended
OPTIONS
TEMP.
Set this option to change the default temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
Set this option to deactivate all spin phases.
Only the drain phase is available.
The related indicator comes on.
Set this option for very delicate fabrics.
The rinses phase uses more water for some
washing programmes.
Rinse Hold
Set this option to prevent the laundry creases.
The related indicator comes on.
There is a water in the drum when the
programme is completed.
The drum turns regularly to prevent the laundry
creases.
The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
PREWASH
With this option you can add a prewash phase to a
washing programme.
The relevant indicator illuminates.
Use this option to add a pre-wash phase before
the washing phase.
This option is recommended for heavily soiled
laundry, especially if containing sand, dust, mud
and other solid particles.
This option can increase the
programme duration.
EASY IRON
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration to
the type of laundry.
The related indicator comes on.
EXTRA RINSE
With this option you can add a few rinses
according to the selected washing programme.
Use this option for people with allergies to
detergent residues and with sensitive skin.
This option increases the programme
duration.
The corresponding indicator illuminates.
NIGHT
The intermediate and the final spinning phases are
suppressed and the programme ends with water in
the drum. This helps to reduce creasing. As the
programme is very quiet, it is suitable for use at
night time when cheaper electricity tariffs are
available. In some programmes the rinses are
performed with more water. The door stays locked.
The drum turns regularly to reduce creasing. You
must drain the water to unlock the door. If you
touch the Start/Pause button, the appliance
performs the only draining phase.
15
The appliance empties the water out
automatically after 18 hours
approximately.
DELAY START
With this option you can delay the start of a
programme to a more convenient time.
Touch the button repeatedly to set the required
delay. The time increases from 30 minutes to 20
hours.
The display shows the indicator and the
selected delay time. After touching the Start/Pause
button, the appliance begins the countdown
and the door is locked.
FLEXITIME
When you set a washing programme, the display
shows the default duration and dashes.
Touch FlexiTime button to reduce the
programme duration according to your needs. The
display shows the new programme duration and a
number of dashes will decrease accordingly:
suitable for a full load of normally soiled
garments.
to wash items with daily soil (max. half load
recommended).
to wash quickly items with almost no soil.
The FlexiTime is available only with the programmes
in the table.
indicator
Eco 40-60
Cottons
Synthetics
Delicates
Dark Colours
1)
1) Defaullt duration for all programmes.
SETTINGS
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
To activate/deactivate this option, press
and at the same time until the indicator
comes on/goes off.
You can activate this option:
After you press : the options and the
programme knob are locked.
Before you press : the appliance cannot
start.
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
To activate/deactivate this option press
and at the same time until the indicator
comes on/goes off.
ACOUSTIC SIGNALS
The acoustic signals operate when:
The programme is completed.
The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press and at the same time for 3 seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
16
BEFORE FIRST USE
During installation or before first use
you may observe some water in the
appliance. This is residual water left in
the appliance after a full functional test
in the factory to ensure the appliance
is delivered to customers in perfect
working order and is no cause for
concern.
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Put a small quantity of detergent in the
compartment for washing phase.
4. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
1. Open the appliance door
2. Empty the pockets and unfold the items before
you put them in the appliance.
3. Put the laundry in the drum, one item at a time.
Make sure not to put too much laundry in the drum.
4. Close the door firmly.
Make sure that no laundry gets caught
between the seal and the door to
avoid risk of water leakage and
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage rubber parts of
the washing machine.
17
FILLING THE DETERGENT AND ADDITIVES
Compartment for washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
Maximum level for quantity of liquid
additives.
Flap for powder or liquid deter-
gent.
When you set a prewash programme (or option), put the detergent for prewash phase directly into the
drum.
Always follow the instructions that you find on the packaging of the detergent products, but
we recommend that you do not exceed the maximum indicated level ( ). This quantity will
however guarantee the best washing results.
After a washing cycle, if necessary, remove any detergent residue from the detergent
dispenser.
LIQUID OR POWDER DETERGENT
The default position of the flap is A (powder deter-
gent).
To use liquid detergent:
1. Remove the drawer. Push the drawer edge in the
place with the arrow (PUSH) to remove the drawer
easily.
18
2. Adjust the flap in position B.
3. Put back the drawer in the recess.
When you use the liquid detergent:
Do not use gelatinous or thick liq-
uid detergents.
Do not put more liquid then 120
ml.
Do not set the programme with
prewash.
Do not set the delay start.
When the flap is in position B and you want to use
powder detergent:
1. Remove the drawer.
2. Adjust the flap in position A.
3. Put back the drawer in the recess.
SETTING A PROGRAMME
1. Turn the programme knob and set the
programme:
The indicator flashes.
The display shows the level of the Time
Manager, the programme duration and the
indicators of the phases of the programme.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message .
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press .
The indicator of stops to flash and
stays on.
The indicator starts to flash on the
display.
The programme starts, the door locks, the
display shows the indicator .
The drain pump can operate for a short time
when the appliance fills water.
After approximately 15 minutes from
the start of the programme:
The appliance adjusts automatically
the programme duration agree with
the laundry load.
The display shows the new value.
STARTING A PROGRAMME WITH THE
DELAY START
1. Press Delay Start again and again until the
display shows the delay you want to set.
The related indicator comes on the display.
2. Press :
The appliance starts the countdown.
The door locks, the display shows the
indicator .
When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the delay start before you press the
. To cancel the delay start:
Press to set the appliance
to pause.
Press Delay Start until the
display shows '.
Press again to start the
programme immediately.
19
THE AUTOSENSE SYSTEM LOAD
DETECTION
After touching the Start/Pause button:
1. The AutoSense System starts estimating the
weight of the load to calculate the real
programme duration. During this phase the
display shows the simple animation.
2. After about 10-15 minutes new cycle duration
is displayed.
The appliance automatically adjusts the
programme duration to the load to achieve
perfect washing results in the minimum
possible time.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press .
The indicator flashes.
2. Change the options.
3. Press again.
The programme continues.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR WHEN THE DELAY
START OPERATES
While a delay start operates, the appliance door is
locked and the indicator is on.
1. Press to pause the appliance.
The indicator starts flashing.
2. Wait about 2 minutes until the door lock
indicator stops flashing and goes off.
3. You can open the door.
4. Close the door and press the again.
The delay start continues to operate.
OPENING THE DOOR WHEN THE
PROGRAMME OPERATES
While a programme operates, the appliance door is
locked and the indicator is on.
CAUTION! If the temperature and
level of the water in the drum are too
high, you cannot open the door.
1. Turn the programme knob to position to
deactivate the appliance.
2. Wait for some minutes and then open the
appliance door.
3. Close the appliance door.
4. Set the programme again.
AT THE END OF THE PROGRAMME
The appliance stops automatically.
The acoustic signal operates (if it is activated).
In the display comes on.
The indicator of the goes off.
The door lock indicator flashes for a few
minutes, then goes off.
You can open the door.
Remove the laundry from the appliance. Make
sure that the drum is empty.
Close the water tap.
Turn the programme knob to position to
deactivate the appliance.
Keep the door ajar, to prevent the mildew and
odours.
The washing programme is completed, but
there is water in the drum:
The drum turns regularly to prevent the creases
in the laundry.
The door lock indicator is on. The indicator
flashes. The door stays locked.
You must drain the water to open the door.
To drain the water:
1. Press . The appliance drains the water and
spins.
2. When the programme is completed, the door
lock indicator flashes for a few minutes.
When it goes off, you can open the door.
3. Turn the programme knob to position to
deactivate the appliance.
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
20
STAND-BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates.
The energy saving status decreases the energy
consumption when the appliance is on the stand
by.
All indicators and the display go off.
The indicator of the flashes slowly
Press one of the options to deactivate the
energy saving status.
If you set a programme or an option
that ends with water in the drum, the
energy saving status function doesn't
activate to remind you to drain the
water.
HINTS AND TIPS
WARNING! Refer to Safety chapters.
THE LAUNDRY LOAD
Divide the laundry into: white, coloured,
synthetics, delicates and wool.
Follow the washing instructions on the laundry
care labels.
Do not wash white and coloured items together.
Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first couple of times.
Turn multilayered fabrics, wool and items with
printed illustrations inside out.
Pre-treat stubborn stains.
Wash stubborn stains with a special detergent.
Be careful with curtains. Remove the hooks and
put the curtains in a washing bag or pillowcase.
A very small load can cause balance problems
with the spin phase leading to excessive
vibration. If this occurs:
a. interrupt the programme and open the
door (refer to "Daily Use" chapter);
b. manually redistribute the load so that the
items are spaced evenly around the tub;
c. press the Start/Pause button. The spin
phase continues.
Avoid washing garments full of long animal hair
or poor quality garments releasing lots of fluff
that could block the drain circuit and therefore
requiring the Service assistance.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts, cords, shoelaces, ribbons
and any other loose elements.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, shoelaces, ribbons, etc. ).
Empty pockets and unfold the items.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENT TYPE AND QUANTITY
The choice of detergent and use of correct
quantities not only affects your wash performance,
but also helps to avoid waste and protect the
environment:
Use only detergents and other treatments
specially made for washing machines. First,
follow these generic rules:
powder detergents for all types of fabric,
excluding delicate. Prefer powder
detergents containing bleach for whites and
laundry sanitization,
21
liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special ones for
woollens only.
The choice and quantity of detergent will
depend on: type of fabric (delicates, woollens,
cottons, etc), the colour of clothes, size of the
load, degree of soiling, wash temperature and
hardness of the water used.
Follow the instructions that you find on
packaging of the detergents or other treatments
without exceeding the indicated maximum level
( ).
Do not mix different types of detergents.
Use less detergent if:
you are washing a small load,
the laundry is lightly soiled,
there is large amounts of foam during
washing.
When using detergent tabs or pods, always put
them inside the drum, not in the detergent
dispenser.
Insufficient detergent may cause:
unsatisfactory washing results,
the wash load to turn grey,
greasy clothes,
mould in the appliance.
Excessive detergent may cause:
sudsing,
reduced washing effect,
inadequate rinsing,
a greater impact for the environment.
ECOLOGICAL HINTS
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
Normally soiled laundry may be washed
without prewash in order to save detergent,
water and time (the environment is protected
too!).
Loading the appliance to the maximum
capacity indicated for each programmes
helps to reduce energy and water
consumption.
With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
To use the correct quantity of detergent, refer to
the quantity suggested by the detergent
producer and check the water hardness of you
domestic system. Refer to 'Water hardness'.
Set the maximum possible spin speed for
the selected washing programme before
drying your laundry in a tumble dryer. This
will save energy during drying!
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To find out the water hardness in your area, contact
your local water authority.
Use the correct quantity of water softener. Follow
the instructions that you find on the packaging of
the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
The appliance is intended for normal
household use only.
Read the chapter carefully for best
maintenance and care.
PERIODIC CLEANING SCHEDULE
Periodic cleaning helps to extend the life of
your appliance.
After each cycle, keep the door and the detergent
dispenser slightly ajar to get air circulation and dry
the humidity inside the appliance: this will prevent
mildew and odours.
If the appliance is not used for a long time: close
the water tap and unplug the appliance.
Indicative periodic cleaning schedule:
Descaling Twice a year
Maintenance wash Once a month
Clean door seal Every two months
Clean drum Every two months
22
Clean detergent dis-
penser
Every two months
Clean the inlet hose
and the valve filter
Twice a year
The following paragraphs explain how you should
clean each part.
REMOVING FOREIGN OBJECTS
Make sure that pockets are empty and
all loose elements are tied up before
running your cycle. Refer to 'The
laundry load' in 'Hints and tips'.
Remove any foreign objects (such as metal clip,
buttons, coins, etc) that you may find in the door
seal, the inlet hose filter and the drum. Refer to
'Door seal with double lip trap', 'Cleaning the drum'
and 'Cleaning the inlet hose and the valve filter'
paragraphs. If necessary, please contact the
Authorised Service Centre.
EXTERNAL CLEANING
Clean the appliance with mild soap and warm water
only. Fully dry all the surfaces. Do not use a
scouring pads or any scratching material.
CAUTION! Do not use alcohol,
solvents or chemical products.
CAUTION! Do not clean the metal
surfaces with chlorine-based
detergent.
DESCALING
If the water hardness in your area is
high or moderate, we recommend that
you use a water descaling product for
washing machines.
Regularly examine the drum to check for limescale.
Regular detergents already contain water softening
agents, but we recommend to run a cycle with an
empty drum and a descaling product occasionally.
Always follow the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
The repeated and prolonged use of low
temperature programmes can cause detergent
deposits, fluff residues, bacterial growth inside the
drum and the tub. This could generate bad odours
and mildew. To eliminate these deposits and clean
the inner part of the appliance, run a maintenance
wash regularly (at least once a month).
Refer to Cleaning the drum chapter.
CLEANING THE DRUM
Regularly examine the drum to prevent unwanted
deposits.
Rust deposits in the drum may occur due to rusting
foreign body in the washing or tap water containing
iron
Clean the drum with special products for stainless
steel.
Always follow the instructions that you
find on the packaging of the product.
Do not clean the drum with acidic
descaling products, scouring products
containing chlorine or iron or steel
wool.
For a thorough clean:
1. Remove all laundry from the drum.
2. Run a Cottons programme with the highest
temperature.
3. Add a small quantity of powder detergent into
the empty drum, in order to rinse out any left
residues.
DOOR SEAL WITH DOUBLE LIP TRAP
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that fall
off the clothes to be drained out with the water.
Regularly examine the seal. Coins, buttons, other
small items can be recovered at the end of the
cycle.
Clean it when needed, using ammonia cream
cleanser agent without scratching the seal surface.
Always obey the instructions that you
find on the packaging of the product.
23
CLEANING THE DETERGENT DISPENSER
1.
2.
3.
4.
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
2
3
24
45°
20°
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
CONSUMPTION VALUES
INTRODUCTION
This user manual reports two different tables in order to favour a
gradual passage from a regulation to the other:
Regulation EU 1061/2010, valid up to 28th of February 2021,
is related to the Energy Efficiency classes from A+++ to D,
Regulation EU 2019/2023, valid from 1st March 2021, is rela-
ted to the Energy Efficiency classes from A to G set by Regula-
tion EU 2019/2014.
See the web link www.theenergylabel.eu for detailed informa-
tion about Energy Label.
The QR code on the energy label supplied with the appliance pro-
vides a web link to the information related to the performance of
the appliance in the EU EPREL database. Keep the energy label
for reference together with the user manual and all other docu-
ments provided with this appliance.
It is also possible to find the same information in EPREL using the
link https://eprel.ec.europa.eu and the model name and prod-
uct number that you find on the rating plate of the appliance. Refer
to 'Product description' chapter for the position of the rating plate.
25
LEGEND
kg Laundry load. h:mm Programme duration.
kWh Energy consumption. °C Temperature in the laundry.
Litres Water consumption. rpm Spin speed.
%Remaining moisture at the end of spinning phase. The higher is the spin speed, the higher is
the noise and the lower is the remaining moisture.
Values and programme duration may differ depending on different conditions (e.g. room tem-
perature, water temperature and pressure, load size and type of laundry, supply voltage) and
also if you change the default setting of a programme.
ACCORDING TO COMMISSION
REGULATION EU 2019/2023
Eco 40-60 pro-
gramme kg kWh Litres h:mm % °C rpm1)
Full load 8 1.150 55 3:30 52 45 1351
Half load 4 0.905 45 2:40 52 42 1351
Quarter load 2 0.410 39 2:40 54 28 1351
1) Maximum spin speed.
Power consumption in different modes
Off (W) Stand-by (W) Delay start (W)
0.48 0.48 4.00
Time to Off/Standby mode is 15 minutes maximum.
ACCORDING TO REGULATION 1061/2010
Standard cotton programmes. Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tres)
Approximate
programme
duration
(minutes)
Remaining
moisture
(%)1)
For Standard 60°C cotton:
Set Eco 40-60 at 60°C 8 0.96 52 244 52
For Standard 60°C cotton:
Set Eco 40-60 at 60°C 4 0.73 40 210 52
26
Standard cotton programmes. Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tres)
Approximate
programme
duration
(minutes)
Remaining
moisture
(%)1)
For Standard 40°C cotton:
Set Eco 40-60 at 30°C 4 0.62 41 196 52
1) At the end of spin phase.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC .
COMMON PROGRAMMES
These values are indicative only.
Programme kg kWh Litres h:mm % °C rpm1)
Cottons2)
90°C 8 2.60 85 3:25 52 85 1400
Cottons
60°C 8 1.70 80 3:00 52 55 1400
Cottons3)
20°C 8 0.48 80 3:00 52 20 1400
Synthetics
40°C 3 0.68 55 2:00 35 40 1200
Delicates4)
30°C 2 0.26 45 1:00 35 30 1200
Wool
30°C 1,5 0.24 60 1:05 30 30 1200
1) Reference indicator of the spin speed.
2) Suitable for washing heavily soiled textiles.
3) Suitable for washing lightly soiled cottons.
4) It also performs as quick washing cycle for lightly soiled laundry.
27
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
ALARM CODES AND POSSIBLE FAILURES
The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to
the tables).
WARNING! Deactivate the appliance before carrying out any check.
With some problems, the display shows an alarm code and the Start/
Pause button may flash continuously:
Problem Possible solution
The appliance does not
fill with water properly.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the inlet hose has no kinks, damages or bends.
Make sure that the connection of the water inlet hose is correct.
This problem may be also caused by the clogged drain circuit. Please
contact the Authorised Service Centre.
Make sure that the filter of the inlet hose and the filter of the valve are
not clogged. Refer to 'Care and cleaning'.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
This problem may be caused by the clogged drain circuit. Please con-
tact the Authorised Service Centre.
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain phase.
Set the drain programme if you set an option which ends with water in
the tub.
The appliance door is
open or not closed cor-
rectly.
Make sure that the door is properly closed.
Internal fail. No commu-
nication between elec-
tronic elements of the
appliance.
The programme was not finished properly or the appliance stopped
too early. Switch the appliance off and on again.
If the alarm code appears again, contact the Authorised Service Cen-
tre.
The mains supply is un-
stable.
Wait until mains supply is stable.
28
If the display shows other alarm codes, deactivate and activate the appliance. If
the problem continues, contact the Authorised Service Centre.
In case of different problem with the washing machine check the table below for
possible solutions.
Problem Possible solution
The programme does
not start.
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is no damaged fuse in the fuse box.
Make sure that the Start/Pause has been touched.
If the delay start is set, cancel the setting or wait for the end of count-
down.
Deactivate the Child Lock function if it is on.
Check the position of the knob on the selected programme.
The appliance fills with
water and drains imme-
diately.
Make sure that the drain hose is in the correct position. The hose may
be positioned too low. Refer to "Installation instruction".
The spin phase does
not operate or the
washing cycle lasts lon-
ger than usual.
Set the spin programme.
This problem may be caused by the clogged drain circuit. Please con-
tact the Authorised Service Centre.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the
floor.
Make sure that the couplings of the water hoses are tight and there is
not water leakages.
Make sure that the water inlet hose and the drain hose have no dam-
ages.
Make sure you use the correct detergent and the correct quantity of it.
You cannot open the
appliance door.
Make sure that a washing programme that ends with water in tub, has
not been selected.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance. Contact the
Authorised Service Centre.
The appliance makes an
unusual noise and vi-
brates.
Make sure the levelling of the appliance is correct. Refer to "Installa-
tion instruction".
Make sure that the packaging and/or the transit bolts are removed.
Refer to "Installation instruction".
Add more laundry in the drum. The load may be too small.
The programme dura-
tion increases or de-
creases during pro-
gramme execution.
The AutoSense System is able to adjust the programme duration ac-
cording to the type and the laundry load size. Refer to "The AutoSense
System load detection" in "Daily Use" chapter.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you wash
the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
29
Problem Possible solution
Too much foam in the
drum during the wash-
ing cycle.
Reduce the quantity of detergent.
After the check, activate the appliance. The programme continues from the point
of interruption.
If the problem occurs again, contact the Authorised Service Centre.
The necessary data for the service centre are on the rating plate.
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
30
*
WWW.ZANUSSI.COM/SHOP
192915260-A-322020
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zanussi ZWF845B4PW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zanussi ZWF845B4PW in de taal/talen: Engels als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info