765778
13
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
GETTING
STARTED?
EASY.
User Manual
ZWF144A2DG
EN User Manual
Washing Machine
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
2
staff kitchen areas in shops, offices and other working
environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments;
areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 10 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
3
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
When unpacking the appliance, It is possible to
see water flowing from the drain hose. This is
due to the testing of the appliance with the use
of water in the factory.
You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
Make sure that there is access to the tap after
the installation.
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
operates. The glass can get hot.
Make sure that all metal objects are removed
from the laundry.
INTERNAL LIGHTING
WARNING! Risk of injury.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
The following spare parts will be available for 10
years after the model has been discontinued:
motor and motor brushes, transmission between
motor and drum, pumps, shock absorbers and
4
springs, washing drum, drum spider and related
ball bearings, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, filters and
aquastops, printed circuit boards, electronic
displays, pressure switches, thermostats and
sensors, software and firmware including reset
software, door, door hinge and seals, other
seals, door locking assembly, plastic peripherals
such as detergent dispensers. Please note that
some of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3 8
5
6
6
4
9
7
10 11
1Worktop
2Detergent dispenser
3Control panel
4Door handle
5Rating plate
6Feet for levelling the appliance
7Drain hose
8Inlet hose connection
9Mains cable
10 Transit bolts
11 Hose support
5
00000000
00A
Mod. xxxxxxxxx
000V ~ 00Hz 0000 W
910000000 00
A
B
C
Prod.No.
D
The rating plate reports the model name (A) , product
number (B), electrical ratings (C) and serial number (D).
TECHNICAL DATA
Dimension Width/ Height/ Total depth 59,7 cm /84,7 cm /65,8 cm
Electrical connection Voltage
Overall power
Fuse
Frequency
230-240 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and moisture
ensured by the protective cover, except where the low voltage
equipment has no protection against moisture
IPX4
Water supply pressure
1)
Minimum
Maximum
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Water supply 2) Cold water
Maximum Load Cotton 10 kg
Spin Speed Maximum spin speed 1351 rpm
1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your do-
mestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
INSTALLATION
WARNING! Refer to Safety chapters.
UNPACKING
1. Open the door. Remove all the items from the
drum.
Accessories delivered with the
appliance may vary depending on
the model.
2. Put the packaging element on the floor behind
the appliance and carefully put it down onto its
rear side. Remove the polystyrene protection
from the bottom.
1
2
6
CAUTION! Do not lay washing
machine on its front.
3. Put the appliance back into an upright position.
Remove the power supply cable and the drain
hose from the hose holders.
WARNING! It is possible to see
water flowing from the drain hose.
This is because the washing
machine has been tested at the
factory.
4. Remove the three transit bolts and pull out the
plastic spacers.
We recommend that you keep
the packaging and the transit
bolts for any transport of the
appliance.
5. Put the plastic caps, that you find in the user
manual bag, in the holes.
INFORMATION FOR INSTALLATION
Positioning and levelling
Adjust the appliance correctly to prevent vibration,
noise and movement of the appliance when it
operates.
1. Install the appliance on a flat hard floor. The
appliance must be levelled and stable. Make sure
that the appliance does not touch the wall or other
units and there is air circulation below the
appliance.
2. Loosen or tighten the feet to adjust the level. All
feet must rest firmly on the floor.
WARNING! Do not put cardboard,
wood or equivalent materials below
the appliance feet to adjust the level.
The inlet hose
CAUTION! Make sure there is no
damage to hoses and there are no
leaks from the couplings. Do not use
an extension hose if the inlet hose is
too short. Contact the service centre
for a replacement inlet hose.
1. Connect the water inlet hose to the back of the
appliance.
20º20º
45º45º
2. Position it toward left or right depending on the
positon of the water tap. Make sure that the inlet
hose is not in vertical position.
3. If necessary, loosen the ring nut to set it in the
correct position.
4. Connect the water inlet hose to the cold water
tap with 3/4'' thread.
Water drainage
The drain hose should stay at a height of no less
than 60 cm and not more than 100 cm.
7
You can extend the drain hose to
maximum 400 cm. Contact the
authorised service centre for the other
drain hose and the extension.
It is possible to connect the drain hose in different
ways:
1. Make a U shape with the drain hose and put it
around the plastic hose guide.
2. On the edge of a sink - Fasten the guide to the
water tap or to the wall.
Make sure that the plastic guide
cannot move when the appliance
drains and the drain hose end is not
immersed in the water. There may be a
return of dirty water into the appliance.
3. If the end of the drain hose looks like this (see
the picture), you can push it directly into the stand
pipe.
4. To a stand pipe with vent hole - Insert the drain
hose directly into a drain pipe. Refer to the
illustration.
The end of the drain hose must always
be ventilated , i.e. the inner diameter of
the drain pipe (min. 38 mm - min. 1.5")
must be larger than the external
diameter of the drain hose.
5. Without the plastic hose guide, to a sink spigot-
Put the drain hose in the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain hose makes a loop to
prevent particles going into the appliance from the
sink.
ø16
1
W011
2
Connect the drain hose to the spigot and tighten it
with a clamp. Make sure that the drain hose makes
a loop to prevent particles going into the appliance
from the sink.
6. Position the hose directly to a built-in drain pipe
in the room wall and tighten it with a clamp.
8
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
ELECTRICAL CONNECTION
At the end of installation you can connect the mains
plug to the mains socket.
The rating plate on the inner edge of the appliance
door and the 'Technical Data' chapter indicate the
necessary electrical ratings. Make sure that they are
compatible with the mains power supply.
Check that your domestic electrical installation can
take the maximum load required, also taking into
account any other appliances in use.
Connect the appliance to an earthed socket.
The power supply cable must be easily accessible
after installing the appliance.
For any electrical work required to install this
appliance, contact our Authorised Service Centre.
The manufacturer does not accept any
responsibility for damage or injury through failure to
comply with the above safety precaution.
ACCESSORIES
AVAILABLE IN WWW.ZANUSSI.COM/SHOP
OR FROM AUTHORISED DEALER
Read carefully the instructions supplied with the
accessory.
Only appropriate accessories
approved by ZANUSSI ensure the
safety standards of the appliance. If
unapproved parts are used, any claims
will be invalidated.
FIXING PLATE KIT
If you install the appliance on a plinth that is not an
accessory supplied by ZANUSSI, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
STACKING KIT
The tumble dryer can be stacked on the top of the
washing machine only by using the correct
stacking kit.
WARNING! Do not put the tumble
dryer under the washing machine.
Verify the compatible stacking kit by
checking the depth of your appliances.
9
CONTROL PANEL
SPECIAL FEATURES
Your new washing machine meets all modern
requirements for an effective treatment of laundry
with low water, energy and detergent consumption
and will care for fabrics.
The AutoAdjust System automatically adjusts
the programme duration to the laundry in the
drum to achieve perfect washing results in the
minimum possible time. Read the paragraph
"The AutoAdjust load detection " for more
details.
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that
fall off the clothes to be drained out with the
water, in such a way that there is no need by the
customer to access this area for regular
maintenance and cleaning. Read the chapter
"Care and Cleaning" for best maintenance and
care.
CONTROL PANEL DESCRIPTION
23 4 5
11 10 7
1
6
89
1Programme dial
2Display
3Delay Start touch button
4FlexiTime touch button
5Start/Pause touch button
6Easy Iron touch button
7Extra Rinse touch button
8Prewash touch button
9Spin reduction options touch button
No Spin option
Rinse Hold option
Night option
10 Temp. touch button
11 ON/OFF push button
10
suitable for a full load of normally soiled
garments.
a quick cycle for a smaller lightly soiled
garments (max. half load recommended).
the shortest cycle to freshen up a small
amount of laundry.
The FlexiTime is available only with the programmes
in the table.
indicator
Eco 40-60
Cottons
Synthetics
Dark Colours
1)
indicator
Eco 40-60
Cottons
Synthetics
Dark Colours
1) Defaullt duration for all programmes.
START/PAUSE
Touch the Start/Pause button to start, pause
the appliance or interrupt a running programme.
PROGRAMMES
PROGRAMME CHART
Programme
Default tempera-
ture
Temperature range
Reference spin
speed
Spin speed
range
Maximum load Programme description
(Type of load and level of soiling)
Washing programmes
Eco 40-60
40 °C 1)
60 °C - 30 °C2)
1400 rpm
(1400- 800
rpm)
10 kg White cotton and fast-coloured cotton.
Normally soiled items. The energy consump-
tion decreases and the time of the washing
programme is extended, ensuring good wash-
ing results.
Cottons
40°C
90°C - Cold
1400 rpm
(1400- 800
rpm)
10 kg White cotton and coloured cotton. Nor-
mally, heavily and lightly soiled items.
Synthetics
40°C
60°C - Cold
1200 rpm
(1200- 800
rpm)
4 kg Synthetic items or mixed fabric items.
Normally soiled items.
Delicates
30°C
40°C - Cold
1200 rpm
(1200- 800
rpm)
2 kg Delicate fabrics such as acrylics, viscose
and mixed fabrics requiring gentler
washing. Normally and lightly soiled items.
Wool
40 °C
40°C - Cold
1200 rpm
(1200- 800
rpm)
1,5 kg Machine washable wool, hand washable
wool and other fabrics with «hand wash-
ing» care symbol3).
13
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zanussi ZWF144A2DG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zanussi ZWF144A2DG in de taal/talen: Engels als bijlage per email.

De handleiding is 1,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info