765960
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
GETTING
STARTED?
EASY.
User Manual
ZSLN2321
EN User Manual
Dishwasher
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other
working environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments.
2
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 10 (1.0) bar (MPa)
Follow the maximum number of 10 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
WARNING: Knives and other utensils with sharp points must
be loaded in the basket with their points down or placed in a
horizontal position.
Do not leave the appliance with the open door unattended to
avoid stepping accidentally onto it.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
If the appliance has ventilation openings in the base, they must
not be covered e.g. by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
SAFETY INSTRUCTIONS
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
Remove all the packaging.
Do not install or use a damaged appliance.
Do not use the appliance before installing it in
the built-in structure due to safety manner.
Follow the installation instructions supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use the appliance where the
temperature is less than 0 °C.
Install the appliance in a safe and suitable place
that meets installation requirements.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
Warning: this appliance is designed to be
installed / connected to a grounding connection
in the building.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
3
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
The water inlet hose has a safety valve and a
sheath with an inner mains cable.
WARNING! Dangerous voltage.
If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
USE
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
Do not drink and play with the water in the
appliance.
Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
Do not store items or apply pressure on the
open door of the appliance.
The appliance can release hot steam if you open
the door while a programme operates.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
The following spare parts will be available for 7
years after the model has been discontinued:
motor, circulation and drain pump, heaters and
heating elements, including heat pumps, piping
and related equipment including hoses, valves,
filters and aquastops, structural and interior
parts related to door assemblies, printed circuit
boards, electronic displays, pressure switches,
thermostats and sensors, software and firmware
including reset software. Please note that some
of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
The following spare parts will be available for 10
years after the model has been discontinued:
door hinge and seals, other seals, spray arms,
drain filters, interior racks and plastic peripherals
such as baskets and lids.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
4
PRODUCT DESCRIPTION
43
7
8
956
10
11
12
1Upper spray arms
2Lower spray arm
3Filters
4Rating plate
5Salt container
6Air vent
7Rinse aid dispenser
8Detergent dispenser
9Lower basket
10 Upper basket
11 Cutlery drawer
The graphic is a general overview. For
more details, refer to other chapters or
documents provided with the
appliance.
CONTROL PANEL
1 2 3 4 5 6
1On/Off button/Reset button
2Delay start button
3Indicators
4Programme buttons
5
5Extra Power button 6AUTO programme button
INDICATORS
Indicator Description
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to
"Before first use".
Salt indicator. It is on when the salt container needs refilling. Refer to "Before first
use".
Machine Care indicator. It is on when the appliance needs internal cleaning with the
Machine Care programme. Refer to "Care and cleaning".
Drying phase indicator. It is on when a programme with the drying phase is selec-
ted. It flashes when the drying phase operates. Refer to "Programme selection".
PROGRAMME SELECTION
PROGRAMMES
BA C
A. 30 min is the shortest programme suitable
for dishwashing a load with fresh and light
soil.
Pre-rinse is a programme for rinsing off
food remains from the dishes. It prevents
odours forming in the appliance. Do not use
detergent with this programme.
B. 90 min is a programme suitable for
dishwashing and drying normally soiled items.
C. ECO is the longest programme offering the
most efficient use of energy and water
consumption for crockery and cutlery with
normal soil. This is the standard programme for
test institutes. 1)
AUTO
This programme automatically adjusts the
dishwashing cycle to the type of load.
The appliance senses the degree of soil and the
amount of dishes in the baskets. It adjusts the
temperature and quantity of water as well as the
wash duration.
OPTIONS
You can adjust the programme selection to your
needs by activating options.
Extra Power
This option improves the dishwashing results of the
selected programme. It increases the wash
temperature and duration.
1) This programme is used to assess compliance with the UK Ecodesign for Energy-Related Products and
Energy Information Regulations.
6
PROGRAMMES OVERVIEW
Programme Dishwasher
load Degree of soil Programme phases Options
30 min Crockery, cut-
lery
Fresh Dishwashing 50 °C
Intermediate rinse
Final rinse 45 °C
AirDry
Extra Power
Pre-rinse All All Prewash Not applicable
90 min Crockery, cut-
lery, pots,
pans
Normal, lightly
dried-on
Dishwashing 60 °C
Intermediate rinse
Final rinse 55 °C
Drying
AirDry
Extra Power
ECO Crockery, cut-
lery, pots,
pans
Normal, lightly
dried-on
Prewash
Dishwashing 50 °C
Intermediate rinse
Final rinse 55 °C
Drying
AirDry
Extra Power
AUTO Crockery, cut-
lery, pots,
pans
All Prewash
Dishwashing 50 -
60 °C
Intermediate rinse
Final rinse 60 °C
Drying
AirDry
Not applicable
Machine
Care
For cleaning the appliance interi-
or. Refer to "Care and Cleaning".
Cleaning 70 °C
Intermediate rinse
Final rinse
AirDry
Not applicable
Consumption values
Programme 1) 2) Water (l) Energy (kWh) Duration (min)
30 min 7.9 - 9.7 0.543 - 0.664 30
Pre-rinse 2.8 - 3.4 0.011 - 0.014 15
90 min 8.5 - 10.4 0.743 - 0.909 90
ECO 9.9 0.754 240
AUTO 8.0 - 10.7 0.683 - 1.047 120 - 170
Machine Care 7.4 - 8.9 0.396 - 0.484 60
1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quan-
tity of dishes and the degree of soil can change the values.
2) The values for programmes other than ECO are indicative only.
7
Information for test institutes
To receive the necessary information for conducting
performance tests (e.g. according to: BS
EN60436 ), send an email to:
info.test@dishwasher-production.com
In your request, include the product number code
(PNC) from the rating plate.
For any other questions regarding your dishwasher,
refer to the service book provided with your
appliance.
BASIC SETTINGS
You can configure the appliance by changing basic
settings according to your needs.
Number Settings Values Description1)
1Water hardness From level 1 to
level 10 (default:
5)
Adjust the level of the water softener according
to the water hardness in your area.
2Rinse aid level From level 0 to
level 8 (default:
5)
Adjust the level of the rinse aid according to the
necessary dosage.
3End sound On
Off (default)
Activate or deactivate the acoustic signal for the
end of a programme.
4Auto door open On (default)
Off
Activate or deactivate the AirDry.
5Key tones On (default)
Off
Activate or deactivate the sound of the buttons
when pressed.
1) For more details, refer to the information provided in this chapter.
You can change the basic settings in setting mode.
When the appliance is in setting mode, the
indicators on the control panel represent available
settings. For each setting, a dedicated indicator
flashes:
1 3 2
4 5
SETTING MODE
How to enter setting mode
You can enter setting mode before starting a
programme. You cannot enter setting mode while
the programme is running.
To enter setting mode, press and hold
simultaneously 30 min and ECO for about 3
seconds.
The light related to and the indicator
flash.
The indicators , and are on.
The lights related to the programme buttons
are on.
How to navigate in setting mode
You can navigate in setting mode using programme
buttons.
8
BA C
A. Previous button
B. OK button
C. Next button
Use Previous and Next to switch between the
basic settings and to change their value.
Use OK to enter the selected setting and to
confirm changing its value.
How to change a setting
Make sure the appliance is in setting mode.
1. Press Previous or Next until the indicator
dedicated to the desired setting flashes.
The light related to indicates the current setting
value:
For the settings with two values (on and
off), the light is either on (= the setting is
on) or off (= the setting is off).
For the settings with multiple values (levels),
the light flashes. The number of flashes
indicates the current setting value (e.g. 5
flashes + pause + 5 flashes... = level 5).
2. Press OK to enter the setting.
The indicator related to the setting is on.
The other indicators are off.
The light related to indicates the current
setting value.
3. Press Previous or Next to change the value.
4. Press OK to confirm the setting.
The new setting is saved.
The appliance returns to the setting
selection.
5. Press and hold simultaneously 30 min and
ECO for about 3 seconds to exit setting mode.
The appliance returns to the programme selection.
The saved settings remain valid until you change
them again.
THE WATER SOFTENER
The water softener removes minerals from the water
supply, which would have a negative effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. Set the right level of the
water softener to assure good washing results.
Water hardness
German degrees
(°dH)
French degrees
(°fH) mmol/l Clarke de-
grees Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
9
German degrees
(°dH)
French degrees
(°fH) mmol/l Clarke de-
grees Water softener level
<4 <7 <0.7 < 5 1 2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
Regeneration process
For the correct water softener operation, the resin
of the softener device needs to be regenerated
regularly. This process is automatic and is the part
of the normal dishwasher operation.
When the prescribed quantity of water (see values
in the table) has been used since the previous
regeneration process, a new regeneration process
will be initiated between the final rinse and the
programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting, it may
occur also in the middle of the programme, before
the rinse (twice during a programme). Regeneration
initiation has no impact on the cycle duration,
unless it occurs in the middle of a programme or at
the end of a programme with a short drying phase.
In such cases, the regeneration prolongs the total
duration of a programme by additional 5 minutes.
Subsequently, the rinsing of the water softener that
lasts 5 minutes may begin in the same cycle or at
the beginning of the next programme. This activity
increases the total water consumption of a
programme by additional 4 litres and the total
energy consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more than
one in the same cycle) may prolong the programme
duration by another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
All the consumption values mentioned
in this section are determined in line
with the currently applicable standard
in laboratory conditions with water
hardness 2.5mmol/L (water softener:
level 3) according to the regulation:
UK Ecodesign 2021/745.
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
THE RINSE AID LEVEL
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically released
during the hot rinse phase. It is possible to set the
released quantity of rinse aid.
When rinse aid chamber is empty, the rinse aid
indicator is on notifying to refill rinse aid. If the
drying results are satisfactory while using multi-
tablets only, it is possible to deactivate the
dispenser and the indicator. However, for best
drying performance, always use rinse aid and keep
the rinse aid indicator active.
To deactivate the rinse aid dispenser and indicator,
set the level of rinse aid to 0.
END SOUND
You can activate an acoustic signal that sounds
when the programme is completed.
10
Acoustic signals sound also when a
malfunction of the appliance occurs. It
is not possible to deactivate these
signals.
AIRDRY
AirDry improves the drying results. The appliance
door opens automatically during the drying phase
and remains ajar.
AirDry is automatically activated with all
programmes other than Pre-rinse.
The duration of the drying phase and the door
opening time vary depending on the selected
programme and options.
CAUTION! Do not try to close the
appliance door within 2 minutes after
automatic opening. This can cause
damage to the appliance.
CAUTION! If children have access to
the appliance, we advise to deactivate
AirDry. The automatic opening of the
door may pose a danger.
KEY TONES
The buttons on the control panel make a click
sound when you press them. You can deactivate
this sound.
BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the level
of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start the programme 30 min to remove any
residuals from the manufacturing process. Do
not use detergent and do not put dishes in the
baskets.
After starting the programme, the appliance
recharges the resin in the water softener for up to 5
minutes. The washing phase starts only after this
procedure is complete. The procedure is repeated
periodically.
THE SALT CONTAINER
CAUTION! Use rough salt designed
for dishwashers only. Fine salt
increases the risk of corrosion.
The salt is used to recharge the resin in the water
softener and to assure good washing results in
daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container (only for
the first time).
3. Fill the salt container with 1 kg of salt (until it is
full).
4. Carefully shake the funnel by its handle to get
the last granules inside.
5. Remove the salt around the opening of the salt
container.
11
6. Turn the cap of the salt container clockwise to
close the salt container.
CAUTION! Water and salt can come
out of the salt container when you fill
it. After you fill the salt container,
immediately start a programme to
prevent corrosion.
HOW TO FILL THE RINSE AID DISPENSER
B
C
A
CAUTION! The compartment (C) is for
rinse aid only. Do not fill it with
detergent.
CAUTION! Only use rinse aid
designed specifically for dishwashers.
1. Press the release element (A) to open the lid
(B).
2. Pour the rinse aid in the dispenser (C) until the
liquid reaches the marking "FILL".
3. Remove the spilled rinse aid with an absorbent
cloth to prevent excessive foam formation.
4. Close the lid. Make sure that the lid locks into
position.
DAILY USE
1. Open the water tap.
2. Press and hold until the appliance is
activated.
3. Fill the salt container if it is empty.
4. Fill the rinse aid dispenser if it is empty.
5. Load the baskets.
6. Add the detergent.
7. Select and start a programme.
8. Close the water tap when the programme is
complete.
USING THE DETERGENT
B
C
A
CAUTION! Only use detergent
designed specifically for dishwashers.
1. Press the release button (B) to open the lid (C).
12
2. Put the detergent in the compartment (A). You
can use detergent in tablets, powder or gel.
3. If the programme has a prewash phase, put a
small quantity of detergent on the inner part of
the appliance door.
4. Close the lid. Make sure that the lid locks into
position.
For information about the detergent
dosage, refer to the manufacturer's
instructions on the packaging of the
product. Usually, 20 - 25 ml of gel
detergent is adequate for washing a
load with normal soil.
Do not fill the compartment (A) with
more than 30 ml of gel detergent.
HOW TO SELECT AND START A
PROGRAMME
1. Press the button dedicated to the programme
you want to set.
The light related to the button flashes.
2. Activate Extra Power if desired.
3. Close the appliance door to start the
programme.
HOW TO SELECT AND START THE
PROGRAMME PRE-RINSE
1. To select Pre-rinse, press and hold 30 min for
3 seconds.
The light related to the button flashes.
Extra Power is not applicable to this
programme.
2. Close the appliance door to start the
programme.
HOW TO ACTIVATE EXTRA POWER
1. Select a programme.
2. Press Extra Power.
The light related to the button is on.
Extra Power is not a permanent option
and must be activated every time
before you start a programme.
It is not possible to activate or
deactivate Extra Power while a
programme is running.
Activating Extra Power increases the
water and energy consumption as well
as the programme duration.
HOW TO SELECT AND START THE
PROGRAMME AUTO
1. Press AUTO.
The light related to the button is on.
2. Close the appliance door to start the
programme.
The appliance senses the type of load and adjusts
a suitable wash cycle.
HOW TO DELAY THE START OF A
PROGRAMME
You can delay the start of the selected programme
by 3 hours.
1. Select a programme.
2. Press .
The light related to the button is on.
3. Close the appliance door to start the
countdown.
During the countdown, it is not possible to change
the programme selection.
When the countdown is complete, the programme
starts.
HOW TO CANCEL THE DELAY START WHILE
THE COUNTDOWN OPERATES
Press and hold for about 3 seconds.
The appliance returns to the programme selection.
If you cancel the delay start, you have
to select the programme again.
HOW TO CANCEL A RUNNING
PROGRAMME
Press and hold for about 3 seconds.
The appliance returns to the programme selection.
Make sure that there is detergent in
the detergent dispenser before you
start a new programme.
OPENING THE DOOR WHILE THE
APPLIANCE OPERATES
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration. After
closing the door, the appliance continues from the
point of interruption.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
13
THE AUTO OFF FUNCTION
This function saves energy by switching the
appliance off when it is not operating.
The function comes into operation automatically:
When the programme is completed.
After 5 minutes if a programme was not started.
END OF THE PROGRAMME
When the programme is complete, the Auto Off
function switches the appliance off automatically.
All buttons are inactive except for the on/off button.
HINTS AND TIPS
GENERAL
Follow the hints below to ensure optimal cleaning
and drying results in daily use and to protect the
environment.
Washing dishes in the dishwasher as instructed
in the user manual usually consumes less water
and energy than washing dishes by hand.
Load the dishwasher to its full capacity to save
water and energy. For best cleaning results,
arrange items in the baskets as instructed in the
user manual and do not overload the baskets.
Do not pre-rinse dishes by hand. It increases
the water and energy consumption. When
needed, select a programme with a prewash
phase.
Remove larger residues of food from the dishes
and empty cups and glasses before putting
them inside the appliance.
Soak or slightly scour cookware with firmly
cooked-on or baked-on food before washing it
in the appliance.
Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
You can use dishwasher detergent, rinse aid
and salt separately or you can use the multi-
tablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
Select a programme according to the type of
load and the degree of soil. ECO offers the
most efficient use of water and energy
consumption.
To prevent limescale buildup inside the
appliance:
Refill the salt container whenever
necessary.
Use the recommended dosage of the
detergent and rinse aid.
Make sure that the current level of the water
softener agrees with the hardness of the
water supply.
Follow the instructions in the chapter "Care
and cleaning".
USING SALT, RINSE AID AND DETERGENT
Only use salt, rinse aid and detergent designed
for dishwasher. Other products can cause
damage to the appliance.
In areas with hard and very hard water, we
recommend to use basic dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
Detergent tablets do not fully dissolve with short
programmes. To prevent detergent residues on
the tableware, we recommend that you use
tablets with long programmes.
Always use the correct quantity of detergent.
Insufficient dosage of detergent can result in
poor cleaning results and hard-water filming or
spotting on the items. Using too much detergent
with soft or softened water results in detergent
residues on the dishes. Adjust the amount of
detergent based on the water hardness. Refer
to the instructions on the detergent packaging.
Always use the correct quantity of rinse aid.
Insufficient dosage of rinse aid decreases the
drying results. Using too much rinse aid results
in bluish layers on the items.
Make sure that the water softener level is
correct. If the level is too high, the increased
quantity of salt in the water might result in rust
on cutlery.
WHAT TO DO IF YOU WANT TO STOP USING
MULTI-TABLETS
Before you start using separately detergent, salt
and rinse aid, complete the following steps:
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the 30 min programme. Do not add
detergent and do not put dishes in the baskets.
4. When the programme is completed, adjust the
water softener according to the water hardness
in your area.
5. Adjust the released quantity of rinse aid.
14
BEFORE STARTING A PROGRAMME
Before you start the selected programme, make
sure that:
The filters are clean and correctly installed.
The cap of the salt container is tight.
The spray arms are not clogged.
There is enough salt and rinse aid (unless you
use multi-tablets).
The arrangement of the items in the baskets is
correct.
The programme is suitable to the type of load
and the degree of soil.
The correct quantity of detergent is used.
LOADING THE BASKETS
Always use the whole space of the baskets.
Use the appliance to wash dishwasher-safe
items only.
Do not wash the following materials in the
dishwasher: wood, horn, pewter, copper,
aluminium, delicate ornamented porcelain and
unprotected carbon steel. This can cause them
to crack, warp, discolour, pit or rust.
Do not wash in the appliance items that can
absorb water (sponges, household cloths).
Put hollow items (cups, glasses and pans) with
the opening facing downwards.
Make sure that glasses do not touch each other.
Put light or plastic items in the upper basket.
Make sure that the items do not move freely.
Put cutlery and small items in the cutlery drawer.
Make sure that the spray arms can move freely
before you start a programme.
UNLOADING THE BASKETS
1. Let the tableware cool down before you
remove it from the appliance. Hot items can be
easily damaged.
2. First remove items from the lower basket, then
from the upper basket.
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
CARE AND CLEANING
WARNING! Before any maintenance
other than running the programme
Machine Care, deactivate the
appliance and disconnect the mains
plug from the main socket.
Dirty filters and clogged spray arms
negatively affect the washing results.
Check these elements regularly and, if
necessary, clean them.
MACHINE CARE
Machine Care is a programme designed to clean
the appliance interior with optimal results. It
removes limescale and grease buildup.
When the appliance senses the need for cleaning,
the indicator is on. Start the Machine Care
programme to clean the appliance interior.
How to start the Machine Care programme
Before starting the Machine Care
programme, clean the filters and spray
arms.
1. Use a descaler or a cleaning product designed
specifically for dishwashers. Follow the
instructions on the packaging. Do not put
dishes in the baskets.
2. Press and hold simultaneously Extra Power
and AUTO for about 3 seconds.
The indicators and Extra Power flash.
3. Close the appliance door to start the
programme.
When the programme is complete, the indicator
is off.
INTERNAL CLEANING
Clean the appliance interior with a soft damp
cloth.
Do not use abrasive products, abrasive cleaning
pads, sharp tools, strong chemicals, scourer or
solvents.
Wipe clean the door, including the rubber
gasket, once a week.
To maintain the performance of your appliance,
use a cleaning product designed specifically for
dishwashers at least once every two months.
Carefully follow the instructions on the
packaging of the product.
For optimal cleaning results, start the
programme Machine Care.
15
REMOVAL OF FOREIGN OBJECTS
Check the filters and the sump after each use of the
dishwasher. Foreign objects (e.g. pieces of glass,
plastic, bones or toothpicks, etc) decrease the
cleaning performance and can cause damage to
the drain pump.
CAUTION! If unable to remove the
foreign objects, contact an Authorised
Service Centre.
1. Disassemble the filters system as instructed in
this chapter.
2. Remove any foreign objects manually.
3. Reassemble the filters as instructed in this
chapter.
EXTERNAL CLEANING
Clean the appliance with a moist soft cloth.
Only use neutral detergents.
Do not use abrasive products, abrasive cleaning
pads or solvents.
CLEANING THE FILTERS
The filter system is made of 3 parts.
C
B
A
1. Turn the filter (B) counterclockwise and remove
it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
5. Make sure that there are no residues of food or
soil in or around the edge of the sump.
6. Put back in place the flat filter (A). Make sure
that it is correctly positioned under the 2
guides.
7. Reassemble the filters (B) and (C).
16
8. Put back the filter (B) in the flat filter (A). Turn it
clockwise until it locks.
CAUTION! An incorrect position of
the filters can cause bad washing
results and damage to the appliance.
CLEANING THE LOWER SPRAY ARM
We recommend to clean the lower spray arm
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
1. To remove the lower spray arm, pull it upwards.
2. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
3. To install the spray arm back, press it
downwards.
CLEANING THE UPPER SPRAY ARMS
We recommend to clean the upper spray arms
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
The upper spray arms are placed under the upper
basket. The spray arms (B) are installed in the duct
(A) with the mounting elements (C).
A
B
C
1. Pull out the upper basket.
2. To detach the spray arm, turn the mounting
element clockwise.
3. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
17
4. To install the spray arm back, insert the
mounting element in the spray arm and fix it in
the duct by turning it counterclockwise. Make
sure that the mounting element locks into
place.
TROUBLESHOOTING
WARNING! Improper repair of the
appliance may pose a danger to the
safety of the user. Any repairs must be
performed by qualified personnel.
The majority of problems that may occur can
be solved without the need to contact an
Authorised Service Centre.
Refer to the below table for information on possible
problems.
With some problems, the lights related to the
programme buttons flash intermittently to indicate a
malfunction and the alarm code.
Problem and alarm code Possible cause and solution
You cannot activate the appli-
ance.
Make sure that the mains plug is connected to the mains sock-
et.
Make sure that there is no damaged fuse in the fuse box.
The programme does not start. Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end of
the countdown.
The appliance recharges the resin inside the water softener.
The duration of the procedure is approximately 5 minutes.
The appliance does not fill with
water.
The lights related to the
programme buttons flash 1
time intermittently.
An acoustic signal sounds
intermittently.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
18
Problem and alarm code Possible cause and solution
The appliance does not drain
the water.
The lights related to the
programme buttons flash 2
times intermittently.
An acoustic signal sounds
intermittently.
Make sure that the sink spigot is not clogged.
Make sure that the interior filter system is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
The lights related to the
programme buttons flash 3
times intermittently.
An acoustic signal sounds
intermittently.
Close the water tap.
Make sure that the appliance is correctly installed.
Make sure the baskets are loaded as instructed in the user
manual.
Malfunction of the water level
detection sensor.
The lights related to the
programme buttons flash 4
times intermittently.
An acoustic signal sounds
intermittently.
Make sure that the filters are clean.
Switch the appliance off and on.
Malfunction of the wash pump
or the drain pump.
The lights related to the
programme buttons flash 5
times intermittently.
An acoustic signal sounds
intermittently.
Switch the appliance off and on.
The temperature of the water
inside the appliance is too high
or malfunction of the tempera-
ture sensor occurred.
The lights related to the
programme buttons flash 6
times intermittently.
An acoustic signal sounds
intermittently.
Make sure that the temperature of the inlet water does not ex-
ceed 60°C.
Switch the appliance off and on.
Technical malfunction of the
appliance.
The lights related to the
programme buttons flash
12 times intermittently.
An acoustic signal sounds
intermittently.
Switch the appliance off and on.
19
Problem and alarm code Possible cause and solution
The level of water inside the
appliance is too high.
The lights related to the
programme buttons flash
15 times intermittently.
An acoustic signal sounds
intermittently.
Switch the appliance off and on.
Make sure that the filters are clean.
Make sure that the outlet hose is installed at the right height
above the floor. Refer to the installation instructions.
The appliance stops and starts
more times during operation.
It is normal. It provides optimal cleaning results and energy sav-
ings.
The programme lasts too long. If the delay start option is set, cancel the delay setting or wait
for the end of the countdown.
Activating Extra Power increases the programme duration.
Small leak from the appliance
door.
The appliance is not levelled. Loosen or tighten the adjustable
feet (if applicable).
The appliance door is not centred on the tub. Adjust the rear
foot (if applicable).
The appliance door is difficult
to close.
The appliance is not levelled. Loosen or tighten the adjustable
feet (if applicable).
Parts of the tableware are protruding from the baskets.
The appliance door opens dur-
ing the wash cycle.
The AirDry function is activated. You can deactivate the func-
tion. Refer to "Basic settings".
Rattling or knocking sounds
from the inside of the appli-
ance.
The tableware is not properly arranged in the baskets. Refer to
basket loading leaflet.
Make sure that the spray arms can rotate freely.
The appliance trips the circuit-
beaker.
The amperage is insufficient to supply simultaneously all the ap-
pliances in use. Check the socket amperage and the capacity
of the meter or turn off one of the appliances in use.
Internal electrical fault of the appliance. Contact an Authorised
Service Centre.
Once you have checked the appliance, deactivate
and activate the appliance. If the problem occurs
again, contact an Authorised Service Centre.
For alarm codes not described in the table, contact
an Authorised Service Centre.
WARNING! We do not recommend
using the appliance until the problem
has been completely fixed. Unplug the
appliance and do not plug it in again
until you are certain that it operates
correctly.
20
THE DISHWASHING AND DRYING RESULTS ARE NOT SATISFACTORY
Problem Possible cause and solution
Poor washing results. Refer to "Daily use", "Hints and tips" and the basket load-
ing leaflet.
Use more intensive washing programme.
Activate the Extra Power option to improve the washing re-
sults of a selected programme.
Clean spray arm jets and filter. Refer to "Care and Clean-
ing".
Poor drying results. Tableware was left for too long inside the closed appliance.
Activate the function AirDry to set the automatic opening of
the door and to improve the drying performance.
There is no rinse aid or the dosage of rinse aid is not suffi-
cient. Fill the rinse aid dispenser or set the dosage of rinse
aid to a higher level.
The quality of the rinse aid can be the cause.
Always use rinse aid, even with multi-tablets.
Plastic items may need to be towel dried.
The programme does not have the drying phase. Refer to
"Programmes overview".
There are whitish streaks or blu-
ish layers on glasses and dishes.
The released quantity of rinse aid is too high. Adjust the rinse
aid dosage to a lower level.
The quantity of detergent is too high.
There are stains and dry water
drops on glasses and dishes.
The released quantity of rinse aid is not sufficient. Adjust the
rinse aid dosage to a higher level.
The quality of the rinse aid can be the cause.
The interior of the appliance is
wet.
This is not a defect of the appliance. Humidity condensates
on the appliance walls.
Unusual foam during washing. Use the detergent designed specifically for dishwashers.
Use a detergent from a different manufacturer.
Do not pre-rinse dishes under running water.
Traces of rust on cutlery. There is too much salt in the water used for washing. Refer to
"The water softener".
Silver and stainless steel cutlery were placed together. Do
not place silver and stainless steel items close together.
There are residues of detergent
in the dispenser at the end of the
programme.
The detergent tablet was stuck in the dispenser and was not
washed away by water.
Water cannot wash away the detergent from the dispenser.
Make sure that the spray arms are not blocked or clogged.
Make sure that items in the baskets do not impede the lid of
the detergent dispenser from opening.
Odours inside the appliance. Refer to "Internal cleaning".
Start the Machine Care programme with a descaler or a
cleaning product designed for dishwashers.
21
Problem Possible cause and solution
Limescale deposits on the table-
ware, on the tub and on the in-
side of the door.
The level of salt is low, check the refill indicator.
The cap of the salt container is loose.
Your tap water is hard. Refer to "The water softener".
Use salt and set regeneration of the water softener even
when multi-functional tablets are used. Refer to "The water
softener".
Start the Machine Care programme with a descaler designed
for dishwashers.
If limescale deposits persist, clean the appliance with the
suitable detergents.
Try a different detergent.
Contact the detergent manufacturer.
Dull, discoloured or chipped ta-
bleware.
Make sure that only dishwasher-safe items are washed in the
appliance.
Load and unload the basket carefully. Refer to the basket
loading leaflet.
Place delicate items in the upper basket.
Refer to "Before first use", "Daily
use", or "Hints and tips" for other
possible causes.
TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 446 / 818 - 898 / 550
Electrical connection 1) Voltage (V) 220 - 240
Frequency (Hz) 50
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 10 (1.0)
Water supply Cold water or hot water 2) max 60 °C
Capacity Place settings 10
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to
decrease energy consumption.
LINK TO THE PRODUCT INFORMATION
SHEET
The QR code on the energy label supplied with the
appliance provides a web link to the product
information sheet. Keep the energy label for
reference together with the user manual and all
other documents provided with this appliance.
For more detailed information about the energy
label, visit www.theenergylabel.eu.
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
22
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
23
*
WWW.ZANUSSI.COM/SHOP
156941221-A-402021
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zanussi ZSLN2321 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zanussi ZSLN2321 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info