517530
19
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
19
User’s manual
EN
USE AND OPERATION
OPERATING TIPS
Important
-
When using the robot for the rst time, it is recommended to carefully read the entire manual and to fully understand
it, especially the safety information.
-
Only use the robot for the uses intended by the Manufacturer and do not tamper with any device to obtain different
operating performances.
DESCRIPTION OF ROBOT COMMANDS
The illustration shows the position of the commands on the machine.
A. DISPLAY: it is lit up to display the functions.
B. ON: press to start the mower.
C. START/PAUSE: press to stop the mower, leaving the display on
“stand-by”; in this way, the mower can be programmed. Press again
to restart the mower. If the key is pressed while the mower is charging,
the mower does not resume working until it is pressed again and the
word “PAUSE” disappears from the display.
D. CHARGE: press this key to allow the mower to return to its station
and, consequently, to start recharging the batteries. If pressed while
the robot is being charged, the robot interrupts the charging cycle and
starts operating again.
E. OFF/STOP: press this key to stop the robot, the display turns off.
“ON” KEY (B)DISPLAY (A)
(G) ENTER KEY
7+,6.(<%2$5',621/<$1(;$03/(
OFF - STOP (E) KEY
CHARGE (D) KEY
“START/PAUSE” KEY (C)
” (H) KEY + ” (F) KEY
F. “+” KEY: during operation, press this key to restart the blade. During programming, press this key to increase the values proposed by the
menu.
G. ENTER: during operation, press this key to activate the spiral function. During programming, press to con rm and memorise the selection.
H. “-” KEY: during operation, press to stop the blade. During programming, press to decrease the entries proposed by the menu.
I. STOP/Emergency KEY: Press to stop the mower safely. Only use in case of imminent danger and to perform maintenance on the robot.
MENU ACCESS
The robot functions can be programmed via the different functions of each menu. The table reports the menus available with the relative
functions.
To program the robot, proceed as follows.
1. Press the “ON” key (B).
2. Enter the password (if prompted) (See “Password Entry”).
3. If the robot is turned on when inside the charging station, after a few seconds the message “CHARGING”. appears on the display.
4. Only press the “Start/Pause” key (C) if the robot was turned on when in the charging station. The “PAUSE” function now appears on the
display.
5. Press the “Enter” key (G). This accesses the user programming menu and the “SETTINGS” function appears on the display.
NAVIGATION
Follow these instructions to navigate the user programming menu:
- “+” and “-” (H) and (F): allows scrolling through the menu items in a cyclical manner or changing the value of the function displayed.
- “Enter” (G): moves to the next menu level or con rms and memorises the value shown in the display and skips to the next function.
- “Pause” (C): goes back to the previous menu level until exiting from the programming menu.
- “Off/Stop” (E): turns off the robot without con rming the last function displayed.
The menu is a hierarchal menu which moves from one function to another until arriving at the desired function.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ZCS 9L2BL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ZCS 9L2BL in de taal/talen: Engels als bijlage per email.

De handleiding is 10,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van ZCS 9L2BL

ZCS 9L2BL Gebruiksaanwijzing - Nederlands - 56 pagina's

ZCS 9L2BL Gebruiksaanwijzing - Nederlands - 33 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info