669800
29
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
28
CAMERA CONTROLS (TEAM MODE)
NOTICE: The ST24 mentioned in this chapter is the one bound to the Gimbal/Camera.
GIMBAL PITCH CONTROL (GB603 AND V18/CGO4 GIMBAL CAMERA)
There is a gimbal pitch mode switch on ST24---S1. When the switch is in up position, the
gimbal/gimbal camera is in Angle Mode. Use the K5 (C) of the ST24 to set the pitch/tilt
position of the gimbal/gimbal camera. When the S1 is in bottom position, the
gimbal/gimbal camera is in Velocity Mode. When the right-hand stick is in the middle
position, it means the velocity rate is 0 for the GB603 or V18/CGO4, and it will stop
pitching up/down. When the right-hand stick is above the middle position, the GB603 or
V18/CGO4 will start pitching up. When the right-hand stick is below the middle position, the
GB603 or V18/CGO4 will start pitching down. The distance between the right-hand stick and the
middle position decides the velocity rate, the further distance, the higher velocity it would be.
CAUTION:
You MUST stop recording video in order to take still photos. It will take
approximately 5 seconds to capture a still photo and before you can take another.
CAUTION: ALWAYS stop recording video before turning off the TORNADO
H920/V18/CGO4 to avoid data loss.
CAMERA/GIMBAL YAW CONTROL
There is a gimbal yaw mode switch on ST24---S2. When the switch
position is up, the gimbal/gimbal camera is in Follow Mode. The yaw
control of the gimbal/camera is now disabled. The gimbal/camera will adjust its
yaw direction according to the aircraft’s movements.
when the switch is in the middle position, the gimbal camera is still in
Follow Mode, however, at this time, the yaw control is activated. The
gimbal camera will adjust its yaw direction according to the aircraft’s movements.
When the switch position is down, the gimbal/gimbal camera is in Global Mode. The
Aileron/Roll Control of the right-hand stick take control of the GB603/V18/CGO4 in yaw directions.
Button A = Take Still Photo Button B = Start/Stop Recording Video
NOTICE: When the V18/CGO4 is attached to the TORNADO H920,
V18/CGO4 Zoom In/Out Control Slider (K6)-located on the right side of
the controller-is activated. Users can zoom in or zoom out by switching
K6. When zooming in,V18/CGO4 gimbal camera in pitch and yaw
directions will become slow in the velocity mode. When zooming out,
the movement speed of the V18/CGO4 gimbal camera in pitch and yaw
directions will become fast in the velocity mode.
NOTICE: When using GB603 to switch off the TORNADO, press the stop recording button
to save the images first, then power off the H920 and turn off the camera at last. When
using CGO4 first stop recording then switch off the camera by ST-24 and switch off the
H920 at last. When using V-18 first stop recording then switch off the H920.
CAUTION:
Each time the K6 is pushed to a certain position, it should be pushed back to the
middle position to confirm the setting. Otherwise, the gimbal camera will continue to zoom
in/out until it achieves the maximum/minimum value.
CAUTION: We recommend that the CGO4/V18 gimbal camera should be operated according
to the above steps strictly, otherwise it may cause unexpected results of lens failing to retract
or video loss etc.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yuneec Tornado H920 Industry bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yuneec Tornado H920 Industry in de taal/talen: Engels als bijlage per email.

De handleiding is 3,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info