638625
20
Verklein
Vergroot
Pagina terug
1/33
Pagina verder
VARINO GRANDE 350 - 600
We reserve the right to make changes to dimensions and construction 18 Edition 10.07.2015
© Copyright YGNIS AG CH-Ruswil
6.9.3. Sensor assembly
Junction boxes or sockets are to be avoided. Sensor and extra-low-voltage cables must be laid separately from
mains lines. Use own sensor cable with max. 100 m length, cable 2 x 1 mm
2
not screened
Cable length: up to 25 m cable cross section: 0.25 mm
2
Cable length: up to 50 m cable cross section: 0.5 mm
2
Cable length: up to 100 m cable cross section: 1.0 mm
2
External sensor: In 2/3 facade height or on 1
st
floor not above windows or below roof preferably
installed on the north or north west side. Avoid direct sunlight. Position to be
arranged with heating planner.
Forward flow sensor: Supply flow clip-on sensor
assemble directly behind the pump (approx. 0.5 m) in the supply flow of the heating
or, if the pump is assembled in the return flow, approx. 1.5 m after the mixer position.
Assembly: assemble on the bare pipe with supplied clamp band, without conductive
paste
Supply flow immersion sensor
assemble directly behind the pump (approx. 0.5 m) in the supply flow of the heating
or, if the pump is assembled in the return flow, approx. 1.5 m after the mixer position.
Assembly: assemble in the pipe bend against the flow direction of the heat transfer
medium
Room remote controls Assemble in the main living quarters on the interior wall. Do not subject to the
influence of sun or external heat (chimney wall, radiator proximity, drafts, televisions,
lighting fixtures). Do not cover with furniture or curtains, mount approx. 1.2 1.5 m
over the floor. Seal installation pipe against drafts. All room sensors and room
remote controls are "active" and therefore directly connected to the device bus. The
cable lengths of all lines on the device bus must not exceed the maximum length of
200 m! Cables 2x1 mm
2
, wires not screened, lay separately from power lines,
junction boxes and sockets are to be avoided.
Return flow sensor, boiler sensor, safety temperature limit devices and temperature monitor are positioned by
works and supplied as-wired.
The O2-sensor is delivered separately and is mounted at commissioning in order to prevent eventual damage to
the sensor during the construction period.
The electrical cables and lines must be laid and secured as shown in the illustration. For strain relief, the cables
should be fastened with cable binders to the threaded rod of the boiler nose peace. Mains and extra-low-voltage
cables (sensor lines, bus lines etc.) are to be routed separately. Unnecessarily long cable loops must not be
rolled up inside of the boiler casing.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ygnis VARINO GRANDE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ygnis VARINO GRANDE in de taal/talen: Engels als bijlage per email.

De handleiding is 1,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Ygnis VARINO GRANDE

Ygnis VARINO GRANDE Installatiehandleiding - Nederlands - 48 pagina's

Ygnis VARINO GRANDE Gebruiksaanwijzing en installatiehandleiding - Nederlands - 34 pagina's

Ygnis VARINO GRANDE Installatiehandleiding - Deutsch, English, Français, Italiano, Espanõl - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info