734892
9
Verklein
Vergroot
Pagina terug
1/31
Pagina verder
9
NOTICE:
ALWAYS apply a small amount of lubricant on
o-rings prior to assembling the garden hose to the pump (C),
high pressure hose (D), spray gun (E), and spray wand (F).
Lubricate all connections shown below, following these
instructions:
1) Inspect and clean connecting surfaces prior to lubrication
and assembly.
2) Use lubricants sparingly during assembly; a light lm is
all that is required.
3) Use a small brush or cotton swab to apply grease directly
to o-rings where they are not accessible(QC tting, M22
tting).
6.Connect Hose and Water Supply to Pump
IMPORTANT! DO NOT run the pump without the water
supply connected and turned on.
Damage to pressure washer resulting from failure to follow
this instruction will void warranty.
NOTICE:
Remove and discard the shipping caps from the
pump’s high pressure outlet and water inlet before attaching
hoses.
1) Uncoil high pressure hose when handle folded, and
attach one end of hose to the base of the spray gun.
Tighten by hand. The other end already assembled to
the pump at the factory.
NOTICE:
The hose only can be uncoiled from the bottom of
the hose reel, it’s recommended to keep the handle folded
for easy unwinding and winding the hose.
WARNING! The high pressure stream of water that the
pressure washer produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER connect high pressure hose to spray wand.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
Always be certain spray gun, wand, nozzles and other
accessories are correctly attached.
2) Before you connect your garden hose to the water inlet,
inspect the inlet screen. Clean the screen if it contains
debris or have it replaced if damaged. Do Not run
the pressure washer if the inlet screen is damaged or
missing.
IMPORTANT! NEVER siphon standing water for the water
supply. Use only cold water (less than 100 °F).
CAUTION! Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or inlet
connector damage.
1) There must be at least 10 ft. (3 m) of unrestricted garden
hose between pressure washer inlet and any device,
such as a vacuum breaker or check valve.
2) Damage to pressure washer resulting from failure to
follow this instruction will void warranty.
3) Run water through garden hose for 30 seconds to ush it
of debris. Turn o water.
4) Connect garden hose (not to exceed 50 ft. in length) to
water inlet. Tighten by hand.
WARNING! Risk of eye injury!
Spray could splash back or propel objects resulting
in serious injure.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of the pressure washer.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
E
F
C
D
Inspect inlet screen. Do Not use if
damaged, clean if dirty
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yardforce Y0GWC3200R0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yardforce Y0GWC3200R0 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info