Handleiding Yamaha MG32-14fx (pagina 11 van 28) (Engels)

618044

Verklein

Vergroot

Pagina terug

1/28

Pagina verder

Front & Rear Panels

MG32/14FX, MG24/14FX

5 AUX Controls (AUX1 to AUX6)

These knobs adjust the channel’s signal levels into AUX buses

1 to 6. Each knob controls the signal into the corresponding

AUX bus.

For AUX1 to AUX4, you use the PRE switch (6) to select

whether the pre-fader or post-fader signal is fed to the bus. For

AUX5 and AUX6, only the post-fader signal can be fed.

These knobs should generally be set close to the position.

On stereo channels, the L (odd) and R (even) input signals are

mixed before moving into the AUX bus.

To enable use of AUX5 and AUX6, you must turn on

the AUX5/AUX6 switch (

8).

6 PRE Switch

Selects whether the pre-fader or the post-fader signal is fed to

the corresponding pair of AUX buses. The upper PRE switch

controls the signal to AUX1 and AUX2; the lower switch con-

trols the signal to AUX3 and AUX4. If the switch is on ( ),

the mixer feeds the pre-fader signal to the corresponding buses.

If off ( ), the mixer feeds the post-fader signal.

There is no PRE switch for AUX5 and AUX6. For

these buses only the post-fader signal is available.

7 EFFECT Controls

These knobs adjust the channel’s signal levels into EFFECT

buses 1 and 2. Since the signal to the EFFECT buses is

post-fader, the level is always determined by the combination

of the EFFECT control and the channel fader.

On stereo channels, the L (odd) and R (even) input signals are

mixed before moving into the EFFECT bus.

These knobs operate as EFFECT controls only if

the AUX5/AUX6 switch is in off position ( ). If the

switch is on, these knobs adjust the output to the

AUX5 and AUX6 buses. (See

8 below.)

8 AUX5, AUX6 Switch

Selects whether the channel signal is sent to AUX buses 5 and

6 or EFFECT buses l and 2. If the switch is on ( ), the signal

goes to AUX5 and 6 buses; if off ( ), the signal goes to the

EFFECT buses. Note that the signal to these buses is always

post-fader.

9 PAN Control (Monaural Channels)

BAL Control (Stereo Channels)

The PAN control adjusts the signal’s pan positioning into the

Group 1-2 bus pair, into the Group 3-4 bus pair, and into the

Stereo bus’s L and R lines.

The BAL control knob sets the balance between left and right

channels. Signals into the L input (odd channel) feed to the

Group 1 and Group 3 buses and to the L line of the Stereo bus.

Signals into the R input (even channel) feed to the Group 2 and

Group 4 buses and to the R line of the Stereo bus.

If you are inputting to a stereo channel through the

L (MONO) jack only, the BAL knob operates as a

PAN knob.

0 ON Switch

Sets the channel on or off. To turn the channel on, press the

switch in ( ) so that it lights up orange. Be sure to turn on all

the channels that you wish to use. If you set the channel off

( ), you cut off all of its signal feed into the ST, GROUP,

AUX, and EFFECT buses.

• The ON switch does not affect the operation of

the PFL switch (A). You can monitor the chan-

nel’s pre-fader signal through the PHONES jack

even when the ON switch is set off.

•To reduce noise, turn all unused channels off

().

A PFL (Pre-Fader Listen) Switch

Use this switch to feed the channel’s pre-channel-fader signal

into the PFL bus, so that you can monitor the signal from the

PHONES jack. To turn PFL feed on, press the switch in ( )

so that it lights up.

• If you switch on output to both the PFL and AFL

buses, the mixer outputs only the PFL signal.

• If you set PFL on for multiple channels, the mixer

feeds the mixed signal from the channels into the

PFL bus.

B PEAK indicator

Lights up when the channel’s post-equalizer signal level comes

within 3 dB of the clipping level.

C SIGNAL indicator

Lights up when a signal is being input into the channel.

D GROUP Switches

Use these switches to feed the channel’s signal to the GROUP

1-2 and/or GROUP 3-4 buses. Setting the switch on ( )

causes the signal to feed into the corresponding GROUP buses.

These switches allow you to independently assign

the signal to groups regardless of the setting of the

ST switch (E).

E ST Switch

Set this switch on ( ) to feed the channel’s signal to the ST

bus.

F Channel Fader

Adjusts the output level of the channel’s signal. Use these fad-

ers to adjust the volume balance among the various channels.

To reduce noise, set the fader sliders for unused

channels all the way down.

NOTE

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Yamaha MG32-14fx Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info