Handleiding Yamaha AN1X (pagina 75 van 122) (Engels)

48724

Verklein

Vergroot

Pagina terug

1/122

Pagina verder

● Source

The Source setting determines which controller (by

Control Change number) is assigned to control the

corresponding Parameter.

You can set the source by Control Change number or by controller name, as

shown in the Settings listed below.

Settings:

CcOff: No controller assigned.

CC1 ~ 95: Selects the Source controller according to Control

Change number, when received by on-board controllers or

incoming MIDI messages.

AT (After Touch): For controlling with keyboard After Touch.

PB (Pitch Bend): For controlling with the Pitch Bend wheel.

KyTrk (Key Track): For controlling with note number

messages generated by pressing the keys.

Vel (Velocity): For controlling with keyboard velocity, or the

strength with which you strike the keys.

KyRnd (Key Random): For controlling with random note

number messages generated by pressing the keys.

A.MW (Assign Modulation Wheel): For controlling with

the Modulation Wheel, and/or by incoming MIDI messages

with the same Control Change number as assigned to the

MW.

A.FV (Assign Foot Volume): For controlling with a

connected Foot Volume controller, and/or by incoming MIDI

messages with the same Control Change number as assigned

to the FV.

A.FC (Assign Foot Control): For controlling with a

connected foot controller, and/or by incoming MIDI messages

with the same Control Change number as assigned to the FC.

A.FS (Assign Footswitch): For controlling with a

connected Footswitch, and/or by incoming MIDI messages

with the same Control Change number as assigned to the FS.

A.RbX (Assign Ribbon Controller-X): For controlling

with the Ribbon controller X-axis (left and right), and/or by

incoming MIDI messages with the same Control Change

number as assigned to the RbX.

A.RbZ (Assign Ribbon Controller-Z): For controlling

with the Ribbon controller Z-axis (push), and/or by incoming

MIDI messages with the same Control Change number as

assigned to the RbZ.

Kn1~8 (Knob 1 ~ 8): For controlling with a specified

CONTROL knob (when KNOB PARAMETER GROUP

[ASSIGN] is on).

Depending on selected Parameter, the available Source for assignment may be

different. For details of available parameters, see the table of Control Matrix

parameters in the separate Data List book.

You cannot assign the same Source controller and Parameter to more than one

set. If you attempt to, lower-numbered sets will take priority, and "– – –" will

appear in the LCD for higher-numbered sets.

When you select [RIBBON] controller "A.RbX" as the "Source" controller and Pitch

Up/Pitch Down as the "Parameter", the [RIBBON] controller value will be reset to

the center position when you release your finger from the [RIBBON]. The sets

with different Parameters (other than Pitch Up/Pitch Down) keep the position at

which you release your finger.

● Depth

The Depth setting determines the control range of the

Source controller.

Settings:

Depending on the selected Parameter, the available settings

may be different. For details, see the table of Control Matrix

parameters in the separate Data List book.

Direct Control Function

When Depth "Dirct" is selected (0 setting), the Direct Control

function is activated, and you can directly edit the parameter

assigned to the controller within its original range.

Relationship Between Control Matrix And

Utility Control Assign Function

There are two types of Control Change assignment

functions—the Control Matrix and the Utility Control Assign

function. Between the Control Matrix and Utility Control

Assign function (see page 95), you can configure a

sophisticated controller setup to control specific parameters of

the internal tone generator and an external tone generator at

the same time by the eight CONTROL knobs and other

controllers. Control Change assignments made in the Utility

Control Assign function are sent to both MIDI [OUT] as well

as the Control Matrix, where it can be rerouted at will before

reaching the internal tone generator. External Control

Change signals received at MIDI [IN] can be routed through

the Control Matrix to control the AN1x tone generator

parameter of your choice.

AN1x Tone Generator

MIDI IN

MIDI OUT

Utility Control

Assign

Control Matrix

Control Signal Flow

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Yamaha AN1X Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Yamaha AN1X

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info