517061
79
Verklein
Vergroot
Pagina terug
1/89
Pagina verder
74 03D Applications
Yamaha 02R & 03D Applications Guide
28
03D with Video Machine & DA-88
This application shows how the 03D can be used with a video machine and Tascam DA-88
for audio post-production and audio sweetening. Using only the SMPTE timecode from the
video machine, the DA-88 can generate MTC for the 03D. The eight digital tape returns and
18 Mic/Line inputs provide up to 26 inputs.
Connections
The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws
out after installation as the card will not be grounded correctly.
The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape
returns.
YGDAI digital outputs can be configured as bus outs, aux sends, input channel direct
outs, or stereo outs. So although the 03D is a four-bus mixer, assigning the four buses
and four aux sends, or the channel direct outs, to the YGDAI outputs allows eight-track
simultaneous recording. YGDAI output assignments are made on the D.out Setup page,
which can be located using the [DIO] button.
YGDAI digital inputs feed 03D input channels 17 through 24.
The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track
and can output SMPTE timecode or MTC. In addition, a timecode offset can be
specified on the DA-88, so the 03D automix start time can be adjusted. The DA-88 also
has the ability to re-stripe the timecode track.
The video house sync is connected to the Video In BNC connection on the DA-88.
03D Wordclock Setup
The 03D works as a wordclock slave. Any pair of YGDAI digital inputs can be selected as the
wordclock source. Use the [DIO] button to locate the D.in Setup page for wordclock
settings.
DA-88 Wordclock Setup
The DA-88 generates a wordclock signal referenced to the Video In signal (VIDEO). The
sampling rate is set when the DA-88 tape is formatted. This can be either 48 kHz or
44.1 kHz. After formatting, the sampling rate is determined by the formatted tape.
Notes
The DA-88 must be powered up even when it is not being used. Failure to do so may
cause an intermittent pumping noise on the 03D.
On the DA-88 rear panel, set the MACHINE ID to 0.
The optional Tascam SY-88 Sync Board, available from Tascam, must be installed to use
SMPTE timecode and MTC. To use the MTC function, the SY-88 firmware must be
version 3.08 or higher.
The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP
switches 2 and 5 to ON (0). Set internal switch 8 on the SY-88 board marked S2 to ON.
On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is
the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit
recording applications.
Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m) are available
from Tascam
79

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha 03D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha 03D in de taal/talen: Engels als bijlage per email.

De handleiding is 2,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Yamaha 03D

Yamaha 03D Gebruiksaanwijzing - Nederlands - 302 pagina's

Yamaha 03D Gebruiksaanwijzing - Deutsch - 307 pagina's

Yamaha 03D Gebruiksaanwijzing - Français - 300 pagina's

Yamaha 03D Gebruiksaanwijzing - Italiano - 301 pagina's

Yamaha 03D Gebruiksaanwijzing - Português - 141 pagina's

Yamaha 03D Gebruiksaanwijzing - Espanõl - 315 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info