517061
35
Verklein
Vergroot
Pagina terug
1/89
Pagina verder
30 02R Applications
Yamaha 02R & 03D Applications Guide
10
02R with Two DA-88s
This application shows how the 02R can be used with two Tascam DA-88s to create a
24-input, 16-track digital recording system. The 16 tape returns and 24 Mic/Line inputs
provide up to 40 inputs at mixdown. In addition, the 02R’s built-in automation and scene
memory systems provide both dynamic and static mix automation referenced to timecode.
Connections
The Tascam (CD8-TD) cards must be screwed securely in place. Do not leave the screws
out after installation as the cards will not be grounded correctly.
The Tascam digital audio cables (PW-88DL) carry the eight tape sends and returns.
DA-88–A is connected to Slot [1] of the 02R. These tape inputs correspond to tracks one
through eight. DA-88–B is connected to Slot [2] of the 02R. These tape inputs
correspond to tracks nine through sixteen.
The optional SY-88 Sync Board is required for DA-88–A. This enables the dedicated
timecode track, which can be re-striped at anytime, and provides SMPTE timecode and
MTC outputs. A timecode offset can be specified on DA-88–A, so the 02R automix start
time can be adjusted.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
DA-88 Wordclock Setup
DA-88–A works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC
cable, and to the DA-88–B using a PW-88S 15-pin sync cable. The sampling rate is set when
the DA-88 tapes are formatted. This can be either 48 kHz or 44.1 kHz. After formatting, the
sampling rate is determined by the formatted tape.
Notes
The DA-88s must be powered up even when they are not being used. Failure to do so may
cause an intermittent pumping noise on the 02R.
DA-88–A is set to MACHINE ID 0. DA-88–B is set to MACHINE ID 1. Since DA-88–A
works as Control Master, it should be used for synchronized transport and locate
operations.
The optional Tascam SY-88 Sync Board must be installed in DA-88–A to use SMPTE
timecode and MTC. This is available from Tascam. DA-88–B does not require the SY-88
Sync Board nor does its tape have to be striped with timecode. It is synchronized to
DA-88–A via the PW-88S 15-pin sync cable.
The terminator bundled with the PW-88S sync cable should be connected to the SYNC
OUT on DA-88–B to ensure reliable synchronization.
The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP
switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.
To use the MTC function, the SY-88 firmware must be version 3.08 or higher.
On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is
the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit
recording applications.
Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m), and the 15-pin
PW-88S sync cable are available from Tascam.
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yamaha 03D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yamaha 03D in de taal/talen: Engels als bijlage per email.

De handleiding is 2,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Yamaha 03D

Yamaha 03D Gebruiksaanwijzing - Nederlands - 302 pagina's

Yamaha 03D Gebruiksaanwijzing - Deutsch - 307 pagina's

Yamaha 03D Gebruiksaanwijzing - Français - 300 pagina's

Yamaha 03D Gebruiksaanwijzing - Italiano - 301 pagina's

Yamaha 03D Gebruiksaanwijzing - Português - 141 pagina's

Yamaha 03D Gebruiksaanwijzing - Espanõl - 315 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info