674747
133
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
Page 131FT
DX
1200 OPERATING MANUAL
INSTALLATION OF OPTIONAL ACCESSORIES
Setup the FT
DX
1200
The optional
FC-40
$utomatic $ntenna Tuner provides automatic tuning of a coaxial line to present nominal 0-ohm
impedance to the
FT
DX
1200
’s $1T jack.
Before operation can begin, you must instruct the
FT
DX
1200
microprocessor that the
FC-40
is being used. This is done
using the 0enu 0ode
FC-40 EXTERNAL AUTOMATIC ANTENNA TUNER (FOR WIRE ANTENNA)
1. 3ress the
[
MENU
]
button to enter the 0enu mode.
. 5otate the
[
VFO-B/CLAR
]
knob or press the
S
T
button) to select the 0enu Item “
179 TUNER SE-
LECT
”.
3. 3ress the
[
SELECT
]
button, then rotate the
[
VFO-
B/CLAR
]
knob or press the
S
T
button) to select
EXTERNAL
”.
4. 3ress the
[
SELECT
]
button.
. 3ress the
[
MENU
]
button to save the new setting and
exit to normal operation.
Operation
1. 3ress the
[
TUNE
]
button briefly to activate the
$utomatic $ntenna Tuner.
. The
TUNER
” icon will appear in the TFT display.
3. 3ress and hold the
[
TUNE
]
button for one second
to begin automatic tuning. The transmitter will be
engaged, and the “
TUNER
” icon will blink while
tuning is in progress.
4. Tuning will stop automatically when a low SW5
is achieved. You may 3ress and hold the
[
TUNE
]
button for one second while tuning is in progress, to
cancel the automatic tuning.
. To disable the $utomatic $ntenna Tuner, press the
[
TUNE
]
button brieÀy again.
[
VFO-B/CLAR
]
Knob
[
MENU
]
Button
[
TUNE
]
Button
[
SELECT
]
Button
[
S
/
T
]
Button
NOTE:
Be sure to connect a good earth ground to the G1'
terminal of the
FC-40
.
The carrier signal transmits continuously while
tuning is in progress. 3lease monitor the operating
freTuency before beginning the tuning process. Be
sure you are not interfering with others who may
already be using the freTuency.
It is normal to hear the sound of the relays while
tuning is in progress.
If the impedance cannot be matched by the
FC-40
better than 1, and the “
TUNER
” icon blinks, the
microprocessor will not retain the tuning data for that
freTuency, as the
FC-40
presumes that you will want
to adjust or repair your antenna system to correct the
high SW5 condition.
133

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FTDX1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FTDX1200 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info