674769
8
Verklein
Vergroot
Pagina terug
1/173
Pagina verder
C4FM/FM
144/430 MHz
DIGITAL/ANALOG
TRANSCEIVER
FT2DR/DE
Operating Manual
Before Using the Transceiver
Preparation
Basic Operation
Repeater Operation
Using the Memory
Scanning Function
Digital Group Monitor Function
Using the APRS Functions
Using the WIRES-X Functions
Using the GPS Function
Convenient Functions
Communicating with a
Specic Remote Station
Customize Menu Settings for
Individual Use (Set Mode)
Functions to Use a Necessary
Appendix
2
Before Using the Transceiver
Before Using the Transceiver
Table of Contents
Before Using the Transceiver .................................. 2
Introduction ................................................................. 6
Features of the FT2DR/DE .................................... 6
Using the Touch Screen ......................................... 7
How to Read This Manual ...................................... 7
Checking the Supplied Items ................................. 8
Safety Precautions (Be Sure to Read) ....................... 9
Names and Functions of Controls ............................ 14
Transceiver .......................................................... 14
Touch Screen Display .......................................... 15
Entering Letters.................................................... 19
Preparation.............................................................. 20
Attaching the Supplied Accessories ......................... 20
Installing the Antenna........................................... 20
Attaching the Accessory Protective Cap/Belt
Clip ....................................................................... 20
Attaching the Protective Cap ........................... 20
Attaching the Belt Clip ..................................... 20
Attaching a Hand Strap ........................................ 21
Preparing the Battery Pack/External Power
Supply....................................................................... 22
Installing/Removing the Battery Pack .................. 22
Installing the Battery Pack ............................... 22
Removing the Battery Pack ............................. 22
Charging the Battery Pack ................................... 22
How to Use the Battery Case (FBA-39) ............... 25
Connecting an External Power Supply for Use in
Vehicle ................................................................. 26
Connecting to an External Power Supply Using a
Power Cable ........................................................ 27
Using a microSD Memory Card ................................ 29
Usable microSD Memory Cards .......................... 29
Cautions when Using a microSD Memory
Card ..................................................................... 29
Mounting and Dismounting microSD Memory
Card ..................................................................... 29
Formatting a microSD Memory Card ................... 31
Basic Operation ...................................................... 32
Performing Communication ...................................... 32
Turning on the Transceiver .................................. 32
Adjusting the Volume Level.................................. 34
Toggling the Operating Band ............................... 34
Selecting a Frequency Band ................................ 37
Tuning to a Frequency ......................................... 38
Selecting the Communication Mode .................... 39
Transmitting/Receiving Signals ............................ 40
Listening to the Radio ............................................... 42
Listening to the AM/FM Radio .............................. 42
Miscellaneous Settings ............................................. 43
Setting Clock Time ............................................... 43
Muting Audio ........................................................ 44
Changing the Transmission Power Level............. 46
Adjusting the Squelch Level................................. 47
Setting the Frequency Step ................................. 47
Changing the Mode.............................................. 48
Locking Keys and Switches ................................. 49
Attenuator (ATT) Function .................................... 50
Restoring to Defaults (All Reset).......................... 51
Repeater Operation ................................................ 52
Repeater Operation .................................................. 52
Communicating Via the Repeater ........................ 52
Repeater Shift........................................................... 53
Automatic Repeater Shift (ARS) .......................... 53
Tone Calling (1750 Hz) ........................................ 53
Using the Memory .................................................. 54
A Wide Variety of Memory Functions ........................ 54
Registering to Memory Channel .......................... 55
Split Memory ........................................................ 56
Recalling a Memory Channel ............................... 57
Recalling the Home Channels ............................. 57
Returning to the Previous Frequency .............. 58
Changing the Home Channel Frequency ........ 58
Clearing Memories ............................................... 59
Restoring the Cleared Memories .................... 59
Using Memory Tag ............................................... 59
Assigning a Name to a Memory Channel ........ 60
Displaying the Memory Tag ............................. 61
Using Memory Bank ................................................. 62
Registering to Memory Banks .............................. 62
Recalling Memory Bank ....................................... 63
Canceling Memory Channel Registration in
Memory Bank ....................................................... 63
Assigning Name to Memory Bank........................ 64
Convenient Preset Receiver Memory Channels....... 65
Registering Preset Receiver Memory Channels
into Memory Banks .............................................. 66
Recalling Preset Receiver Memory Channel to
Listen to the Weather Broadcast .......................... 66
Recalling Preset Receiver Memory Channel to
Listen to the International VHF (Marine) Radio.... 67
Recalling Preset Receiver Memory Channels to
Listen to World Wide Broadcasts ......................... 68
Worldwide short wave broadcast .................... 69
Scanning Function ................................................. 71
VFO Scan ................................................................. 71
Canceling Scanning ........................................ 72
3
Before Using the Transceiver
Table of Contents
Skipping Frequencies You Do Not Want to
Scan (Skip Search Memory) ........................... 72
Specifying the Frequencies You Do Not Want
to Scan ............................................................ 73
Deleting the Frequency Registered to the Skip
Search Memory Channel ................................ 73
Setting the Receive Operation When
Scanning Stops ............................................... 74
Memory Channel Scanning ...................................... 76
Specifying Skip/Selected Memory
Channels ......................................................... 77
Scanning Only the Specified Memory
Channels ......................................................... 78
Scanning the Memory Bank ................................. 79
Memory Bank Link Scanning .......................... 79
Programmable Memory Channel Scan (PMS) ......... 81
Registering to the Programmable Memory
Channels ......................................................... 81
Performing Programmable Memory Channel
Scan ................................................................ 81
Digital Group Monitor Function
Using the Digital GM Function ................... 83
What is the GM function? ......................................... 83
Standard Operation of the GM Function................... 83
Displaying All Stations (up to 24 Stations)
Operating with the GM Function .......................... 83
Registering IDs of Friends in a Group and
Displaying Only Registered GM Users ................ 84
Deactivating the GM Function.............................. 84
Using the APRS / WIRES-X Functions .................. 85
The APRS (Automatic Packet Reporting System)
Function .................................................................... 85
What is the WIRES-X Function? .............................. 85
Using the GPS Function ........................................ 86
The GPS Function .................................................... 86
Activating the GPS Function..................................... 86
Method of Positioning by GPS.................................. 88
Displaying Position Information of Remote
Stations in Digital Mode ....................................... 88
Saving GPS Information (GPS Log Function)...... 89
Checking Tracks on Your PC ............................... 90
GPS Screen Information and Operation ................... 91
Displaying the GPS Information ........................... 91
Smart Navigation Function ....................................... 93
Real-Time Navigation Function ............................ 93
Backtrack Function .............................................. 93
Registering Your Current Position
(Departure Point)
(up to 3 Positions can Be
Registered) ................................................ 93
Using the Back Track Function ....................... 94
Description of the BACK TRACK Function
Screen.................................................................. 95
Convenient Functions ............................................ 96
Dual Receive (DW) Function .................................... 96
VFO Dual Receive
VFO mode → Priority memory channel ......... 97
Memory Channel Dual Receive
Memory channel → Priority memory
channel ........................................................... 98
Home Channel Dual Receive
Home channel → Priority memory channel .... 98
AF-DUAL Receive Function (Receiving Signals
on Other Frequency Channels While Listening to
Broadcast Radio) .................................................... 100
Listening to a Radio Broadcast Using the
AF-DUAL Receive Function ............................... 100
Setting the Resumption Time of Radio
Reception ........................................................... 101
Using the DTMF Function....................................... 103
Setting the DTMF Memory ................................. 103
Transmitting the Registered DTMF Code .......... 104
Manually Transmitting the DTMF Code ............. 105
Spectrum Analyzer with Signal Strength Graph
Band Scope Function ............................................. 106
Taking Picture Using the Optional Camera-Mounted
Speaker Microphone
Snapshot Function ..............107
Viewing the Saved Image .................................. 108
Transmitting the Saved Image to Other
Transceivers ...................................................... 108
Communicating with a Specific Remote
Station ................................................................... 109
Using the Tone Squelch Function ........................... 109
Selecting the Squelch Type ............................... 109
Setting the Tone Frequency ................................110
Searching for the CTCSS Tone transmitted
by the Remote Station ........................................111
Setting the DCS Code.........................................112
Searching for the DCS Code Used
by the Remote Station ........................................112
Notification of a Call from a Remote Station
by Vibration .........................................................113
Selecting the Vibrator Operation Mode ..........114
Notification of a Call from a Remote Station
by the Bell Function ............................................114
Changing the Number of Times the Bell
Rings ..............................................................115
Calling Only a Specific Station
New Pager Function ................................................116
Flow of Operation to Use the Pager Function .....116
4
Before Using the Transceiver
Table of Contents
Setting the Code for Your Station .......................116
Activating the New Pager Function .....................117
Calling a Specific Station ....................................117
Being Called by the Remote Station
(Standby Operation)............................................118
Customize Menu Settings for Individual Use
(Set Mode) ............................................................. 119
Using Set Mode .......................................................119
Set Mode Operation ............................................119
Resetting the All Set Mode Settings................... 120
Tables of Set Mode Operations .............................. 121
Set Mode: DISPLAY Menu Operations ................... 128
Setting What to Display Using the Smart
Navigation Function ........................................... 128
Setting the Compass Display ............................. 128
Setting the Search Channels for the BAND
SCOPE Function................................................ 128
Changing the Lighting Condition ........................ 129
Selecting the Display Language ........................ 129
Adjusting the LCD Contrast Level ...................... 129
Adjusting the LCD Backlight and Key Button
Light Brightness Level........................................ 130
Changing the Opening Message Displayed
Immediately after Power-on ............................... 130
Displaying the Battery Voltage ........................... 130
Changing the Display Pattern of the S-Meter .... 131
Displaying the Software Version ........................ 131
Set Mode: TX/RX Menu Operations ....................... 132
Reducing Receiver Sensitivity
Attenuator (ATT) Function .................................. 132
Setting the Transmit Modulation Level ............... 132
Switching the Receive Mode.............................. 133
Setting the Squelch Type for the Digital Mode ... 133
Setting the Pop-up Time of the Remote Station
Information ......................................................... 133
Displaying Your Location in Digital Mode ........... 134
Setting the Standby Beep .................................. 134
Adjusting the Microphone Sensitivity
Microphone Gain................................................ 134
Muting Audio ...................................................... 135
Simultaneous Radio Broadcast Reception ........ 135
Set Mode: MEMORY Menu Operations ................. 136
Setting Memory Bank Link ................................. 136
Assigning Name to Memory Bank...................... 136
Assigning Name to Memory Channel ................ 136
Prohibiting Registration to a Memory Channel
Memory Channel Protect Function .................... 137
Setting Memory Skip Function ........................... 137
Setting the Memory Channels Used for
Registration ........................................................ 137
Set Mode: SIGNALING Menu Operations .............. 138
Notification of a Call from a Remote Station
by the Bell .......................................................... 138
Selecting a DCS Code ....................................... 138
Transmitting and Receiving a DCS Code with an
Inverted Phase DCS INVERSION Function....... 138
Setting the Transmission Method of the DTMF
Code .................................................................. 138
Setting the DTMF Code ..................................... 139
Calling Only a Specific Station (New Pager
Function) ............................................................ 139
Enabling No-communication Squelch Function
PR FREQUENCY Function ................................ 139
Adjusting the Squelch Level SQL LEVEL
Function ............................................................. 139
Setting the Squelch to Activate at a Specified
Signal Strength S-Meter Squelch Function ........ 140
Setting the Squelch Type for Transmit and
Receive SQL EXPANSION Function ................. 141
Setting the Type of Squelch ............................... 141
Selecting a CTCSS Tone Frequency ................. 141
Setting the Sound and Speed During Tone
Search Tone Search Function ............................ 141
Set Mode: SCAN Menu Operations........................ 142
Setting the Surveillance Interval Time for Priority
Channels DW INTERVAL TIME Function .......... 142
Setting the Illumination On/Off When Scanning
Stops LAMP Function ........................................ 142
Setting the Time to Resume Scanning SCAN
RE-START Function........................................... 142
Selecting a Receive Operation When Scanning
Stops .................................................................. 143
Setting the Scanning Range .............................. 143
Set Mode: GM Menu Operations ............................ 144
Set Mode: WIRES-X Menu Operations .................. 144
Set Mode: CONFIG Menu Operations.................... 145
Turn Power Off Automatically
Auto Power-Off Function .................................... 145
Preventing Accidental Transmission Busy
Channel Lockout (BCLO) Function .................... 145
Setting the Key Operation Confirmation
Sound................................................................. 146
Turning off the BUSY Indicator .......................... 146
Setting the Clock Shift for the Micro Computer
Clock Type Function .......................................... 147
Setting a Time Interval for Saving GPS Position
Information ......................................................... 147
Permitting/Prohibiting Transfer of Home Channel
Frequency to VFO.............................................. 147
Using the LED Light ........................................... 148
Setting the LOCK Function ................................ 148
5
Before Using the Transceiver
Table of Contents
Setting the Operation of the Key .................. 148
Turning on/off the Transceiver at the Specified Time
Timer Function ................................................... 149
Password Function ............................................ 149
Setting the PTT Delay Time PTT DELAY
Function ............................................................. 150
Setting the ARS Function RPT ARS Function .... 150
Setting the Repeater Shift Direction RPT SHIFT
Function ............................................................. 150
Setting the frequency offset for Repeater Shift
RPT SHIFT FREQ Function ............................... 151
Disabling Receiver While No Signal Is Received
Receiver Battery Save Function ........................ 151
Changing the Frequency Step Manually ............ 151
Setting Clock Time ............................................. 151
Limit the time of a continuous transmission
(TOT Function) ................................................... 152
Setting the Frequency Selection Range for
Operation in VFO Mode VFO MODE
Function ............................................................. 152
Notifying a Call From a Remote Station by
Vibration ............................................................. 152
Swapping the Dial Knob Functions .................... 152
Set Mode: APRS Menu Operations ........................ 153
Set Mode: SD CARD Menu Operations ................. 154
Saving/Loading Data to/from microSD Memory
Card ................................................................... 154
Saving/Loading Memory Channel Information to/
from microSD Memory Card .............................. 155
Saving/Loading GROUP ID Information
to/from a microSD Memory Card ....................... 155
Formatting a microSD Memory Card ................. 156
Set Mode: OPTION Menu Operations .................... 157
Setting the Optional Microphone With Camera
for Use ............................................................... 157
Set Mode: CALLSIGN Menu Operations ................ 158
Functions to Use as Necessary .......................... 159
Using the Transceiver for Packet
Communication....................................................... 159
Clone Operation ..................................................... 160
Connecting an External Device .............................. 161
Connecting to a PC ............................................ 161
Connecting to an External Device...................... 162
Connection Cables............................................. 162
Data Cable (CT-170) ..................................... 162
Data Output Cable (CT-176) ......................... 162
Appendix ............................................................... 163
Optional Parts ......................................................... 163
If you suspect malfunction
Check the following
items before requesting a repair. ...................... 164
The transceiver does not turn on. ................. 164
There is no sound. ........................................ 164
There is no transmission of radio waves. ...... 164
The keys or DIAL does not respond. ............. 164
Index ....................................................................... 166
Specifications ......................................................... 168
6
Before Using the Transceiver
Introduction
Features of the FT2DR/DE
m Digital communication (C4FM (Quaternary FSK), FDMA system) ............................. 39
m Equipped with AMS (Automatic Mode Select) Function ............................................. 39
Automatically selects between 4 modes of transmission according to the signal being
received.
m External power supply connection ............................................................................. 15
m Simultaneous reception on two different bands,
or within the same band (V+V/U+U) .................................................................... 34, 36
m Independent switching keys for A-band and B-band and TX/BUSY display .............. 36
m Wide-band reception over the range of 500 kHz to 999.900 MHz ............................. 36
m Waterproof design equivalent to IPX5, which protects the transceiver
from rain and splashes ............................................................................................... 13
m Large 160×160 dot LCD screen and touch panel ...................................................... 15
m WIRES-X connection support ..................................See WIRES-X instruction manual*
m Equipped with GM function ..................................See GM function instruction manual*
m Large-capacity 1266ch with 24 memory banks (maximum of 100 channels can be
saved on each bank) .................................................................................................. 54
m Display memory tags comprised of up to 16 one-byte characters ............................. 59
m Convenient reception of preset receiver memory channels ....................................... 65
By selecting preset frequencies, you can receive shortwave broadcast,
and international VHF radio stations with ease.
m A wide variety of scan functions ................................................................................. 71
m Built-in GPS unit allowing display of your current location and heading
information ................................................................................................................. 86
m Ready for APRS
®
communication using the world standard 1200 / 9600bps AX25
modem (B-band only) ................................................... See APRS instruction manual*
m High-resolution band scope function to display ± 35 channels ................................ 106
m Equipped with the smart navigation function ............................................................. 93
m A variety of individual selective calling functions; such as tone squelch (CTCSS)
and DCS functions ................................................................................................... 109
m Vibrator to alert you of signal reception, in addition to the audible bell .................... 113
m New pager function for calling only specific stations ................................................ 116
m LED Backlight for easy viewing of the LCD outdoors .............................................. 147
m Battery save function to extend battery operating time .............................................. 46
m Data terminal for communication with external equipment and firmware updates ... 162
m Compatible with microSD memory cards ................................................................... 29
m Snapshot function (an optional camera microphone MH-85A11U is required) ....... 107
* WIRES-X, GM function and APRS instruction manuals are not included in the product
package.
They are available and may be downloaded from the Yaesu.com website.
7
Before Using the Transceiver
Introduction
Using the Touch Screen
y Caution when Using the Touch Screen
Observe the following precautions when using the touch screen. Failing to do so may
result in malfunction or damage.
m Operate the touch screen with your fingers. Do not operate with any pointed objects
including your fingernail or pen.
m Do not apply any excessive force to the touch screen.
m Do not scrub or scratch on the touch screen when cleaning it.
y Restrictions on touch operations
m The touch screen does not respond to any of the flicking and pinching-in/out operations.
m Due to the characteristics of the LCD, when the ambient temperature is low, the touch
screen may respond slowly.
y Touch Screen Upkeep
m After turning off the transceiver, wipe the touch screen with a soft dry cloth.
m Do not use water, chemical agents or mild detergents.
How to Read This Manual
Common explanatory expressions used in this manual are as follows:
Press
...................................................... Indicates to simply press a key or switch.
Press and hold
for over one second ....... Indicates to press a key or switch for over
one second.
Touch [F MW] .................................................. Indicates briefly touching the screen.
Touch [F MW] for over one second ................ Indicates touching the screen for over
one second.
The following notations are also used in this manual.
Caution
...Explains caution to observe during operation.
Tip
...Explains operating suggestions or useful tips.
8
Before Using the Transceiver
Introduction
Checking the Supplied Items
Transceiver
Battery charger
PA-48B/C/F/U* or SAD-14B
* “B” suffix is for use with 120 VAC
(Type-A plug), “C” suffix is for use
with 230-240 VAC (Type-C plug), “F”
suffix is for use with 220 VAC,
and “U” suffix is for use with
230 VAC (Type-BF plug).
Antenna
Belt clip
Battery pack
protective cap
Long life
lithium-ion battery pack
(SBR-14LI: 7.2V,
2,200 mAh)
USB cable
• Quick Manual
Operating Manual
(this manual)
• Warranty Card
Cautions
y Ensure that the name of the dealer from which you purchased the transceiver and the date of
purchase are indicated on the warranty card.
y If any item is missing, contact the dealer from which you purchased the transceiver.
9
Before Using the Transceiver
Safety Precautions (Be Sure to Read)
Be sure to read the safety precautions to use this product safely.
Yaesu is not liable for failures and other problems caused due to misuse or use of this
product by you or a third party. Also, Yaesu is not liable for damages caused through
use of this product by you or a third party except in the case where ordered to pay for
damages under the laws.
Types and Meanings of Symbols
DANGER
Indicates an imminently hazardous situation which, if not
avoided, could result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or only
property damage.
Types and Meanings of Legends
Indicates a prohibited action, not to be done in order to use this product safely.
For example,
indicates that the product should not be disassembled.
Indicates a required action, to be done in order to use this product safely.
For example,
indicates that the power plug should be removed.
DANGER
Do not use this product in “an area
where use of it is prohibited”, e.g., in-
side the hospital, airplane, or train.”
This product can affect electronic or
medical devices.
Do not use this product while riding
a bicycle or driving a car. Accidents
can result.
Be sure to stop the bicycle or car at a safe
place before using this product.
Those who are carrying a medical
device such as a cardiac pacemaker
should not perform transmission
near the device. When transmitting,
use an external antenna and keep as
far as possible away from the exter-
nal antenna.
The radio wave emitted by the transmit-
ter can cause the medical device to mal-
function and result in an accident.
Do not use this product or the battery
charger in a place where inflammable
gas is generated.
A fire or explosion can occur.
10
Before Using the Transceiver
Safety Precautions (Be Sure to Read)
Do not perform transmission in a
crowded place for the safety of per-
sons using a medical device such as
a cardiac pacemaker.
The radio wave emitted from this prod-
uct can cause the medical device to mal-
function and result in an accident.
Do not touch any material leak-
ing from the battery pack with bare
hands.
The chemical that has stuck to your skin
or entered your eye can cause chemical
burns. In such a case, consult the doctor
immediately.
Do not solder or short-circuit the ter-
minal of the battery pack.
A fire, leak, overheating, explosion, or igni-
tion can result.
Do not carry the battery pack together
with a necklace, hair pin, or small metal
objects. A short circuit can result.
If it starts thundering when the exter-
nal antenna is used, immediately turn
off this product and disconnect the
external antenna from it.
A fire, electrical shock, or damage may
result.
WARNING
Do not power this transceiver with a
voltage other than the specified pow-
er supply voltage.
A fire, electric shock, or damage may
result.
Do not use the battery pack for any
model other than the specified trans-
ceiver.
A fire, leak, overheating, explosion, or
ignition can result.
This product has a waterproof struc-
ture and conforms to “IPX5” when
the included antenna and battery
pack are installed and rubber caps
are securely attached to the MIC/SP
jack, EXTDC IN jack, DATA terminal,
and micro SD slot. If this transceiver
gets wet, wipe it with a dry cloth, etc.
do not leave it exposed to the mois-
ture.
Leaving this product in a wet condition
can degrade its performance, shorten its
life, or cause a failure or electrical shock.
Do not make very long transmissions.
The main body of the transceiver may
overheat, resulting in a failure or burns.
Do not disassemble or make any al-
teration to this product.
An injury, electric shock, or failure can
result.
Do not handle the battery pack or
charger with wet hands. Do not insert
or remove the power plug with wet
hands.
An injury, leak, fire, or failure can result.
If smoke or strange odor is emitted
from the main body, battery pack,
or battery charger, immediately turn
the transceiver off; remove the bat-
tery pack, and remove the power plug
from the outlet.
A fire, leak, overheating, damage, igni-
tion, or failure can result. Contact the
dealer from which you purchased this
product or Yaesu Amateur Customer
Support.
Do not use the battery pack which is
externally damaged or deformed.
A fire, leak, heating, explosion, or igni-
tion can result.
Do not use any battery charger which
is not specified by Yaesu.
A fire or failure can result.
When transmitting, keep the trans-
ceiver at least 5.0 mm (3/16 inch)
away from your body.
Use only the supplied antenna. Do
not use modified or damaged anten-
nas.
11
Before Using the Transceiver
Safety Precautions (Be Sure to Read)
Keep the terminals of the battery
pack clean.
If terminal contacts are dirty or corroded,
a fire, leak, overheating, explosion, or
ignition can result.
If charging of the battery pack can-
not be completed within the specified
charging time, immediately remove
the power plug of the battery charger
from the outlet.
A fire, leak, overheating, explosion, or
ignition can result.
CAUTION
Do not dangle or throw this product
by holding its antenna.
This product can hit and injure some-
one. In addition, doing so can result in a
transceiver failure or damage.
Do not use transceiver in a crowded
place.
The antenna can hit someone, resulting
in a injury.
Do not place this transceiver in a
place subject to direct sunlight or
near a heater.
The transceiver can deform or discolor.
Do not place this transceiver in a hu-
mid or dusty place.
A fire or failure can result.
During transmission, keep the anten-
na as far from you as possible.
Long-time exposure to electromagnetic
waves can have a negative impact on
your health.
Do not clean the case with thinner or
benzene.
Use a soft, dry cloth to clean the case.
If the transceiver is not being used
for an extended period, turn it off and
remove the battery pack for safety.
Do not drop, strike, or throw the
transceiver.
A failure or damage may result.
Keep magnetic cards and video tape
away from the transceiver.
The data recorded on cash cards or
video tape can be erased.
Do not use the earpiece microphone,
earphones, or headphones at an ex-
tremely high volume level.
Hearing impairment can result.
Keep this product out of reach of chil-
dren.
An injury, etc. can result.
Install the hand strap and belt clip
securely.
If they are installed improperly, the FT-
2DR/DE may fall or drop, resulting in an
injury or damage.
Do not place a heavy object on the
power cord of the battery charger.
The battery cord can be damaged, re-
sulting in a fire or electric shock.
Do not use the included battery char-
ger to charge any battery pack which
is not specified for use with the char-
ger.
A fire can result.
Do not operate the transmitter near
the TV or radio.
Radio disturbance can occur in the
transceiver, the TV, or the radio.
Do not use any products other than
the specified options and accesso-
ries.
A failure can result.
When the battery charger is not in
use, remove its power plug from the
outlet
12
Before Using the Transceiver
Safety Precautions (Be Sure to Read)
Charge the battery pack within the
temperature range from +5 °C to
+35 °C (+41 °F to +95 °F).
Charging the battery pack outside this
temperature range can cause leak,
overheating, decrease in performance,
or reduction in service life can result.
When unplugging the power cord of
the battery charger, be sure to hold
the power plug.
Pulling the power cord can damage it
and cause a fire or electronic shock.
Before discarding the worn battery
pack, affix tape or the like to its ter-
minals.
Before using this transceiver in a
hybrid or fuel-saving car, be sure to
check with the automobile manufac-
turer regarding use of the transceiver
in that car.
Noise generated by an onboard electri-
cal device (inverter, etc.) can disrupt the
normal operation of the transceiver.
13
Before Using the Transceiver
Safety Precautions (Be Sure to Read)
About Waterproong Feature Conforming to IPX5
When the included antenna and battery pack are installed and the MIC/SP jack, EXT
DC IN jack, DATA terminal, and micro SD slot are securely covered with rubber caps,
this product is moisture and splash resistant. To ensure continued waterproofing
protection, be sure to check the following points before use.
m Check for damages, deterioration, and dirt.
Antenna rubber, key switch rubber, MIC/SP jack, EXT DC IN jack, DATA terminal, micro SD
slot rubber cap, and battery pack joint.
m Cleaning
When this product is contaminated with seawater, sand, or dirt, rinse with fresh water, and then
wipe with a dry cloth immediately.
m Recommended maintenance interval
To insure continued water resistance and optimal performance, it is recommended that
maintenance be performed annually, or when any damage or deterioration is found. Note that
the maintenance service is subject to fees.
m Do not immerse this product in the following liquids:
Sea, pool, hot spring, water containing soap, detergent, or bath additive, alcohol, or chemicals
m Do not leave this product for an extended time in the following places:
Bathroom, kitchen, or humid place
m Other precautions
Since this product is not totally waterproof, it cannot be immersed in water.
14
Before Using the Transceiver
Names and Functions of Controls
Transceiver
Antenna terminal (SMA)*
TX/BUSY LED
Lights green (A-band) or blue (B-band) during
receive and lights red during transmit.
Touch screen display
Touch to set the frequency and various other
settings.
[PTT] switch
Press and hold
to transmit, and release it to
receive.
Pressing [PTT] while in Set mode completes the
Set mode function.
[MONI/T-CALL] switch
USA/EXP version
While
is pressed: Squelch OFF
European version
While
is pressed: T.CALL (1750 Hz)
[SQL] switch
Press
, rotate VOL: Squelch level adjustment
Power switch
When the power is off, press and hold
for
over one second: Power on
When the power is on, press and hold
for
over one second: Power off
When the power is on, press
: Engages and
releases the key lock
[BACK] key
Press to return to the previous screen.
[x] key
In normal mode, press to start WIRES-X.
When WIRES-X is activated, press and hold for
over one second to return to the normal mode.
Battery pack*
DIAL
Rotate to change the frequency or select a
memory channel.
VOL
Adjusts volume. Turn clockwise to increase
the audio level, and turn counterclockwise to
decrease the audio level.
GPS antenna
[DISP] key
Pressing each time switches between the
frequency display and the backtrack display.
Press and hold for over one second to enter Set
mode.
[BAND] key
Pressing each time increases the frequency
band.
[V/M] key
Pressing each time switches between VFO
mode and memory mode.
[A/B] key (switching between operating
bands)
Pressing each time switches between A-band
and B-band.
Press and hold for over one second to switch
between the Dual Band Receive mode and the
Mono Band Receive mode.
Microphone
[GM] key
Press to turn the GM function on/off.
microSD memory card slot*
Open the cover and insert your microSD memory
card.
15
Before Using the Transceiver
Names and Functions of Controls
󰚜
DATA terminal*
To use the clone function, connect to another
FT2DR/DE with an optional clone cable (CT-
168).
When updating the firmware, connect to your
PC using a USB cable.
* For instruction to update the firmware, access
our website.
Connect the optional camera-equipped
microphone (MH-85A11U) to this terminal.
Connect an external GPS to this terminal.
󰚧
MIC/SP jack*
Connect a speaker microphone or earpiece
microphone to this jack.
The waterproof protection cannot be attained
when an external microphone is connected.
Do not connect any microphone which is
not specified by Yaesu. A failure can result.
󰚨
EXT DC IN jack*
When charging the battery pack, connect the
battery charger (PA-48 or SAD-14B) to this jack.
In the USA/EXP market, connect an external
power supply adapter with a cigarette lighter
plug (SDD-13) or an external power cable (E-
DC-6) to this jack.
Do not connect any battery charger which
is not specified by Yaesu. A failure can
result.
*: When the included antenna and battery pack are
installed and the MIC/SP jack, EXT DC IN jack, DATA
terminal, and micro SD slot are securely covered with
rubber caps, the FT2DR/DE meets the waterproofing
performance conforming to IPX5 (See page 13).
Touch Screen Display
This is the A-band display area.
This is the B-band display area.
Displays touch keys.
Displays mode.
In VFO mode, “VFO” is displayed.
In Memory mode, “MR” and the channel
number are displayed.
Display Bar indicates the volume level.
Displays the transmit output icon, the S
meter and the PO meter levels.
S meter: Displays the received signal
strength in 9 steps.
PO meter: Displays the transmit power level
in 4 steps.
H I: High power (5W)
L 3: LOW 3 power (2.5W)
L 2: LOW 2 power (1W)
L 1: LOW 1 power (0.1W*
1
)
Displays the time.
Displays the frequency shift direction during
repeater operation (
see page 52).
-: Minus shift
+: Plus shift
@: Split operation
lights when the mute function is active
( see page 44).
Displays the frequency.
Displays icon types.
: Lights when Auto Power Off is active
( see page 145).
: Lights when DTMF function is
enabled ( see page 103).
: Lights when GPS is acquired ( see
page 86).
: Lights when GPS Log Function is
enabled ( see page 89).
: Lights when a microSD memory card
is inserted ( see page 29).
The battery condition is displayed in 8
steps.
: Full battery power
: Battery is depleted. Charge battery.
: (When blinking) Charge battery
immediately.
*
1
: European version (VHF: 0.05W)
16
Before Using the Transceiver
Names and Functions of Controls
Displays squelch type (
see page 109)
TN: Lights when the tone encoder
function is enabled.
TSQ: Lights when the tone squelch
function is enabled.
DCS: Lights up when the DCS function is
enabled.
RTN: Lights when the reverse tone
function is enabled.
PR: Lights when the idle signal squelch
function is enabled.
PAG: Lights when the pager is enabled.
DC: Lights when the transceiver is set
to send the DCS code only during
transmission.
T-D: Lights when the transceiver is set
to send the CTCSS tone signal
during transmit, and wait for the
DCS code in receive mode.
D-T: Lights when the transceiver is
set to send the DCS code during
transmit, and wait for the CTCSS
tone signal in receive mode.
Displays the APRS baud rate (B-band only)
( APRS function Instruction manual).
Displays operation mode.
FM: FM (Analog) mode
: Auto mode (automatic switching
among Analog AM, Analog FM,
and Digital) *The display of the
“FM” portion differs according to
the selected mode.
DN: Wide digital mode (digital mode
using C4FM modulation)
VW: Wide digital mode (high-quality
digital communication)
appears when the bell function is active
( see page 114).
17
Before Using the Transceiver
Names and Functions of Controls
y Dual Band Screen
A-band and B-band are displayed in a top-down fashion.
Touching [F MW] displays the function menu screen.
Touching [TX M] enables the communication mode to be
fixed on the transmission side.
Touching [MODE] each time switches the operation
mode.
y Function Menu Screen
Touching [F MW] displays the function menu screen.
y Band Scope Screen
The band scope screen can be displayed by touching [SCOPE] from the function menu
screen.
Reference You can change the number of band scope channels
by pressing and holding the
key for over one
second to enter Set mode, then select [DISPLAY][3
BAND SCOPE] to select the desired number of channels
(17ch/35ch/71ch).
18
Before Using the Transceiver
Names and Functions of Controls
y BACKTRACK Screen
Pressing the
key displays the BACKTRACK screen.
The compass setting is displayed to the upper left of the
compass icon. “H-UP” indicates the vehicle direction
of travel is shown at the top of the compass. “N-UP” is
shown when the compass is set to always indicate North
at the top. To change the compass setting, enter Set
mode, then select [DISPLAY][2 HEADING UP].
Upon retrieval of the registered position information, the
distance from the current position is displayed the upper
right of the compass icon.
Touching [YR] displays the position of the received
station on the compass icon (only when the received
signal carries the position information).
Touching [MY] displays your station’s heading direction
on the compass icon.
Touching [MEM] switches to the registration mode to
record.
Touching [] displays the position information registered
with the “” tag. Touching “” while flashing, stores the
position information displayed on the compass icon in the
memory with a “” tag.
Touching [L1] displays the position information registered
with the “L1” tag. Touching [L1] while flashing, the
position information displayed on the compass icon is
stored in the memory with an “L1” tag.
Touching [L2] displays the position information registered
with the “L2” tag. When touching [L2] while flashing,
stores the position information displayed on the compass
icon in the stored in the memory with an “L2” tag.
19
Before Using the Transceiver
Names and Functions of Controls
Entering Letters
The keyboard screen appears for inputting letters, numbers and symbols for your call
sign or a memory channel tag.
y Number Input Screen
y Alphabet Input Screen
Touch [ABC] to display the alphabet input screen.
Touch [A] to display the alphabet (2 byte character)
input screen.
Touch the [1] key to display the numeric (2 byte
character) keypad input screen.
Touch the [123] key to display the numeric keypad input
screen.
Touch [#$%] to display the symbol input screen.
Touch [#] to display the symbol (2 byte character) input
screen.
Repeatedly touch the same key to advance in order through
the characters assigned to the key. Lowercase letters are
displayed, and then uppercase. For example, every time
you touch [abc] key, it changes the characters as follows:
a → b → c → A → B → C
Touch [
] [ ] to move the cursor to left/right in the
text input area.
20
Preparation
Preparation
Attaching the Supplied Accessories
Installing the Antenna
1 Align the bottom side of the antenna with the antenna connector
on the transceiver.
Caution Be sure to hold the thick base of the antenna when installing it
2 Turn the antenna clockwise until it is secured.
Cautions
y Do not hold or twist the upper part of the antenna when
installing or removing it. To do so may break the conductors
inside the antenna.
y Do not key the transmit without installing the antenna. The
transmitter components may be damaged.
y When using an antenna other than the one supplied, or
connecting to an external antenna, ensure that the SWR is
adjusted to 1.5 or lower.
Attaching the Accessory Protective Cap/Belt Clip
Attaching the Protective Cap
If you do not use the belt clip, install the protective cap to
cover the belt clip attaching screw holes on the battery
pack.
Attaching the Belt Clip
1 Turn the battery pack over.
2 Attach the belt clip to the battery pack using the
supplied screws (two).
Cautions
y Be sure to use the supplied screws when attaching the belt
clip. If any other screws are used, the belt clip cannot be
secured firmly to the battery pack and the transceiver may
drop off together with the battery pack; the transceiver and
battery pack may fall off, causing injury, breakage and other
damage.
y Be sure to attach the protective cap when the belt clip is not
used.
21
Preparation
Attaching the Supplied Accessories
Attaching a Hand Strap
If you attach a hand strap to the transceiver, insert its 1 mm diameter string through the
strap hole of the transceiver and thread the strap through the loop to secure it to the
transceiver.
* The hand strap is not supplied.
1 Remove the battery pack.
2 Attach the hand strap.
Caution
Use a hand strap which can withstand the weight of the
transceiver. If you use a hand strap which is not strong enough,
the hand strap can break and the transceiver may fall down,
causing injury, breakage and other troubles.
22
Preparation
Preparing the Battery Pack/External Power Supply
Installing/Removing the Battery Pack
Installing the Battery Pack
1 Insert the bottom tabs of the battery pack in the slots
on the back side lower part of the transceiver.
2 Push the battery in until the battery latches click
securely.
Caution
Charge the battery pack before using the transceiver for the first
time after purchase, or when it has not been used for a long
period time.
Caution
Risk of explosion if battery is replaced by an incorrect typ.
Dispose of used batteries according to the instructions.
Removing the Battery Pack
1 While pressing down the latches, remove the battery
pack.
Press the latches down in the direction of the arrows
as shown in the illustration.
Caution
When releasing the battery latches, be careful not to hurt your
fingers and nails.
Charging the Battery Pack
Cautions
y The battery pack is rechargeable about 300 times. However, improper use such as overcharge or
over-discharge can shorten its service life.
y The battery pack is a consumable item. Recharging the battery pack repeatedly will gradually reduce
the charge capacity and duration of its use.
y If the transceiver is not used for a long period of time with the battery pack installed, deterioration of
the battery pack can accelerate.
y If the transceiver is unused for a long period of time, be sure to store it with the battery pack removed.
When the transceiver and battery are stored for an extended period, install the battery pack biannually
and recharge the battery pack about 50% to prevent it from over-discharging.
y Storing the battery pack in a high-temperature environment can accelerate deterioration. Store the
battery pack in a place where the ambient temperature is −20 °C to +50 °C (−4 °F to +122 °F).
y Be careful not to drop or strongly impact the battery pack. It can break.
Battery latches
Press down on the latches
in the direction of the arrow.
23
Preparation
Preparing the Battery Pack/External Power Supply
Tips
The battery pack contains lithium-ion batteries that can be recharged for repeated use.
The transceiver can be used with either of the following battery packs:
(1) Supplied battery pack: SBR-14LI (7.2 V, 2,200 mAh)
(2) Optional battery pack: FNB-101LI (7.4 V, 1,100 mAh)
When the battery pack is recharged, its output voltage becomes higher (about 8 V) than the
specified value (7.2 V). This is not a malfunction.
Battery charger
PA-48 or SAD-14B (supplied)
Grooves in
battery pack
Rapid Charger Cradle CD-41
(optional)
Rails
1 Install the battery pack.
2 Turn the transceiver off.
3 Insert the plug of the battery charger (PA-48 or SAD-
14B) into the EXT DC IN jack of the transceiver.
Charging starts.
On the top part of the transceiver, the TX/BUSY LED
lights red, and the display indicates “NOW CHARGING”.
The charge level is indicated by a bar graph.
It takes about 9 hours to charge the SBR-14LI battery
pack fully.
When charging is completed, the display will change to
indicate “COMPLETE” and the lamp will light green.
Remark In the USA Version, the TX/BUSY LED is not lit when charging or when charging is
complete. When the charge is complete, the transceiver turns off after 3 minutes.
24
Preparation
Preparing the Battery Pack/External Power Supply
Supplements It takes about 5 hours to charge the FNB-101LI (optional).
The optional Rapid Charger Cradle (CD-41) requires about 5 hours to charge the
supplied battery pack (about 2.5 hours to charge the optional battery pack FNB-
101LI).
Place the battery pack on the CD-41 so that the rails of the CD-41 fit into the
grooves on the battery pack.
When charging the battery pack using the CD-41, the LED on the CD-41 indicates
the state of charging.
During charging: Glows red → Blinks fast → Blinks slowly
Completion of charging: Lights green
4 Remove the plug of the battery charger from the jack of the transceiver.
Cautions
y The supplied PA-48 or SAD-14B battery charger is not adequate to operate the transmit and receive
while charging the battery pack.
y Charging may cause noise in a nearby TV or radio.
Charge the battery pack with the battery charger as far away as possible from a TV or radio.
y If “BATTERY NOT INSTALLED” appears on the LCD and the battery pack is not charged after a lapse
of 11 or more hours, stop charging the battery pack immediately.
If the same message appears again, the battery pack is presumed to be at the end of its service life,
or defective. In this case, replace the battery pack with a new one.
y While charging the battery pack, protect the transceiver from water.
y Charge the battery pack in a place where the ambient temperature is +5 °C to +35 °C (+41 °F to +95
°F).
y If the terminal or electrode of the battery case is dirty, this transceiver can malfunction due to poor
contact, resulting in overheating or rupture. If the terminal or electrode gets dirty, clean it using a dry
cloth or cotton swab.
Tips
The battery charger may become hot during charging. This is not a malfunction.
If
starts blinking, the battery pack charge is depleted. Charge it immediately.
Approximate Operating Time and Remaining Charge Level Indication
Approximate operating time for the transceiver with the fully charged battery pack or
new AA alkaline batteries is as follows:
Band in Use
Digital: OFF
Battery pack
SBR-14LI
Battery pack
FNB-101LI
Battery
FBA-39
Amateur Band
144 MHz band Approx. 12.0 hours Approx. 6.0 hours Approx. 14 hours
430 MHz band Approx. 11.0 hours Approx. 5.5 hours Approx. 13 hours
AM Broadcast Band
Approx. 25.0 hours Approx. 13.0 hours Approx. 16 hours
FM Broadcast Band
Approx. 25.0 hours Approx. 13.0 hours Approx. 16 hours
Band in Use
Digital: ON
Battery pack
SBR-14LI
Battery pack
FNB-101LI
Battery
FBA-39
Amateur Band
144 MHz band Approx. 10 hours Approx. 5.0 hours Approx. 12.0 hours
430 MHz band Approx. 9 hours Approx. 4.5 hours Approx. 11.0 hours
Transmission 6 seconds: Reception 6 seconds (VOL Level 16): Stand By 48 seconds (SAVE1:5)
25
Preparation
Preparing the Battery Pack/External Power Supply
Remark Approximate hours are estimated assuming that the transceiver is operated under the
following conditions. The operation time that this transceiver can be actually used varies
depending on use conditions, ambient temperature, etc.
• When the GPS function is deactivated.
• LAMP MODE SAVE ON (always LAMP OFF)
When the transceiver is repeatedly operated by high-power transmission for 6 seconds
and reception for 6 seconds, and standby for 48 seconds with an amateur ham radio
band selected.
How to Use the Battery Case (FBA-39)
The optional battery case (FBA-39) allows 3 AA Alkaline batteries to be used to power
the FT2DR/DE transceiver.
Tip
When the battery case (FBA-39) is used, the power output level may be selected from:
Low Power (L1): 0.1 W
Low Power (L2): Approximately 0.8 W
Note that Low Power (L3) and High Power are not available.
1 Open the cover.
Lift up the lower right corner of the cover as indicated by the
hand pointer in the illustration.
2 Place the alkaline batteries in the battery case.
Caution Use 3 alkaline batteries. Pay attention to polarities (+ and −)
of the alkaline batteries.
3 Close the cover.
Push the four corners of the cover firmly to close it tightly.
Tip
When the battery charge is low, lights on the LCD. When the
batteries are almost exhausted,
blinks on the LCD.
Cautions
y Lithium/Manganese batteries cannot be used with the FBA-39 battery
case. Rechargeable AA batteries cannot be used, either.
y Do not mix new and old batteries. The service life of new batteries may
decrease.
y If you do not use the transceiver for a long period, remove the batteries
from the battery case.
y If the terminal or electrode of the battery case is dirty, the transceiver can
malfunction due to poor contact, resulting in overheating or explosion.
If the terminal or electrode gets dirty, clean it using a dry cloth or cotton
swab.
26
Preparation
Preparing the Battery Pack/External Power Supply
Connecting an External Power Supply for Use in Vehicle
(USA/EXP version only)
The optional external power supply adapter
with a cigarette lighter plug (SDD-13) allows
the transceiver to be used in a vehicle.
1 Turn off the transceiver.
2 Insert the plug of the external power
supply adapter with a cigarette lighter plug
(SDD-13) in the EXT DC IN jack of the
transceiver.
3 Insert the cigarette lighter plug of the
external power supply adapter in the
cigarette lighter socket of the vehicle.
Cautions
y The SDD-13 is compatible with a 12 V DC cigarette lighter socket. Do not connect the SDD-13 to a
24 V DC cigarette lighter socket.
y Use the transceiver at the minimum required transmit power level to prevent overheating.
y Do not continue transmitting for a prolonged period of time. The transceiver may overheat, resulting
in malfunction or burns.
y To operate the transceiver for 7 hours or longer, it is recommended that the battery pack be replaced
with the optional battery case (FBA-39).
y Recharging the fully-charged battery pack repeatedly can shorten its service life. Be extremely careful
not to continually recharge the battery when operating the transceiver using an external power supply.
y While charging the battery pack, protect the transceiver from water.
y Charge the battery pack in a place where the ambient temperature is +5 °C to +35 °C (+41 °F to +95
°F).
y If the terminal or electrode of the battery pack is dirty, the transceiver can malfunction due to poor
contact, resulting in overheating or rupture. If the terminal or electrode gets dirty, clean it using a dry
cloth or cotton swab.
Tips
The SBR-14LI battery pack can be charged in approximately 9.0 hours using the external power
supply (approximately 5 hours to charge the optional battery pack FNB-101LI). If the transceiver is
turned on while the battery pack is charging, the charging time will increase slightly.
Charging stops automatically when the battery pack has been fully charged.
The external power supply can be used with the battery case installed.
If the transceiver is connected to the external power supply with the transceiver turned off,
“CONNECTED TO EXTERNAL POWER” appears on the LCD for about 20 seconds later “BATTERY
NOT INSTALLED” appears.
To cigarette lighter
socket of vehicle
EXT DC IN jack
External power
supply adapter with
a cigarette lighter plug
SDD-13optional
27
Preparation
Preparing the Battery Pack/External Power Supply
Connecting to an External Power Supply Using a Power Cable
(USA/EXP version only)
The optional power cable (E-DC-6) allows the transceiver to be connected to an external
power supply.
1 Turn off the transceiver.
2 Connect the optional external power supply
cable (E-DC-6) to an external power supply.
Remarks Connect the red/black wire or white/red
wire to the positive (+) terminal of the
external power supply and the black wire
to the negative (−) terminal.
Set the voltage of the external power
supply at 12 to 14 V.
3 Insert the plug of the external power supply
into the EXT DC IN jack of the transceiver.
Cautions
y When using the transceiver with the external power supply cable (E-DC-6) connected to an external
power supply, pay attention to the following:
The power supply voltage must be between 12 V and 14 V.
If the voltage exceeds 16 V, malfunctions and damage to the electric circuits of the transceiver may
result. Take extra care.
Connect the red/black wire or white/black wire of the external power supply cable (E-DC-6) to the
positive (+) terminal of the external power supply and the black wire to the negative (−) terminal.
Use an external power supply having sufficient current capacity (3 A or more).
If the transceiver is used with the supplied antenna connected, the transmit RF may interfere with
the external power supply, resulting in malfunction or failure. When using an external power supply,
remove the supplied antenna and connect an external antenna. Place the external power supply
sufficiently away from the transceiver to avoid RF interference.
y Use the transceiver at the minimum required transmission power level to prevent overheating.
y Do not continue transmitting for a prolonged period. The transceiver may overheat, resulting in
malfunction or a burn injury.
y To operate the transceiver for 7 hours or longer, it is recommended that the battery pack be replaced
with the optional battery case (FBA-39).
y Recharging the fully-charged battery pack repeatedly can shorten its service life. Be extremely careful
not to continually recharge the battery when operating the transceiver using an external power supply.
y While charging the battery pack, protect the transceiver from water.
y Charge the battery pack in a place where the ambient temperature is +5 °C to +35 °C (+41 °F to +95
°F).
y If the terminals or electrodes of the battery pack are dirty, the transceiver may malfunction due to poor
contact, resulting in overheating or rupture. If the terminals or electrodes get dirty, clean them using
a dry cloth or cotton swab.
Connect the external
antenna.
External power supply
External power supply
cable E-DC-6
(optional)
28
Preparation
Preparing the Battery Pack/External Power Supply
Tips
The SBR-14LI battery pack can be charged in approximately 9.0 hours using the external power
supply (approximately 5 hours to charge the optional battery pack FNB-101LI). If the transceiver is
turned on while the battery pack is charging, the charging time will increase slightly.
If the transceiver is connected to the external power supply with the transceiver turned off,
“CONNECTED TO EXTERNAL POWER” appears on the LCD for about 20 seconds, and then
“BATTERY NOT INSTALLED” appears.
29
Preparation
Using a microSD Memory Card
Using a microSD memory card with the transceiver allows the following functions.
Backing up the transceiver data and information
Saving memory information
Saving data other than images
Saving GPS log data
Saving image data captured with the optional camera-equipped microphone (MH-
85A11U)
Saving messages downloaded with the GM function or WIRES-X function
Usable microSD Memory Cards
This transceiver only supports the following capacity of microSD and microSDHD
memory cards.
• 2GB • 4GB • 8GB • 16GB • 32GB
Cautions when Using a microSD Memory Card
Do not bend or place heavy objects on the microSD memory card.
microSD memory cards formatted on other devices may not properly save information
when used with this transceiver. Format microSD memory cards again with this
transceiver when using memory cards formatted with another device.
Do not remove the microSD memory card or turn the transceiver off, while saving data
to a microSD memory card is in progress.
Do not insert anything other than a microSD memory card into the microSD memory
card slot of the transceiver.
Do not attempt to forcefully remove a mounted microSD memory card.
Mounting and Dismounting microSD Memory Card
1
Press and hold for over one second.
The transceiver will turn off.
30
Preparation
Using a microSD Memory Card
2 Open the microSD cover on the side of the
transceiver.
3 Insert the microSD memory card into the card slot
until you hear a clicking sound (as shown in the
figure at the right).
Cautions Ensure that the microSD memory card is facing
the proper direction when inserting it.
Do not touch the terminal of the microSD memory
card.
Do not push the microSD
memory card into this space.
4 Close the microSD cover.
5 Press and hold for over one second.
The transceiver will turn on. When the microSD
memory card is properly detected,
lights on the
display.
Tip
Removing the microSD memory card
To remove the microSD memory card, as done in step 3 above,
push the memory card in until you hear a clicking sound, then
remove the memory card.
Caution
Do not turn off the transceiver while the data is being written to
the microSD memory card. Doing so may corrupt the data.
31
Preparation
Using a microSD Memory Card
Formatting a microSD Memory Card
Format a new microSD memory card following the steps below before use.
Caution
Formatting a microSD memory card erases all data saved on it. If you are going to format the
microSD memory card you are using, be sure to check the data saved on it before formatting.
1 Press and hold key for over one second.
The “SETUP MENU” screen appears.
2 Touch [SD CARD].
3 Touch [4 FORMAT].
[FORMAT?] appears on the LCD.
4 Touch [OK].
Tip To cancel formatting, select [Cancel].
Initialization starts and “Waiting” appears.
When formatting is completed, a beep sounds and [COMPLETED] appears on the
LCD.
Tip You can also select each item by rotating the DIAL and pressing the key.
32
Basic Operation
Basic Operation
Performing Communication
To communicate using the transceiver in the analog communication mode, follow the
procedure below:
Turn on the transceiver
Adjust the Volume Level
Select an Operating Band
Select a Frequency Band
Turn in to a Frequency
Perform Communication
Turning on the Transceiver
1
Press and hold for over one second.
When the transceiver is turned on for the first time
after purchase, the call sign input message appears
on the LCD. Press the
key to proceed to the
call sign input screen. When the transceiver is turned
on the second time, and subsequently, the opening
screen appears followed by the frequency screen.
33
Basic Operation
Performing Communication
2 Input the call sign (toggle the alphabet input screen,
and the number input screen when necessary).
Supplement The alphabet input screen can be switched to the
number input screen by touching [123].
The number input screen can be switched to the
alphabet input screen by touching [ABC].
3 Press .
The call sign is set and the frequencies of both A-band
and B-band are displayed simultaneously.
Supplement Factory settings are:
A-band (upper): 144.000 MHz
B-band (lower): 430.000 MHz
Tip You can change the information such as the power supply
voltage and the opening message displayed at power-
on. For example, press and hold
key for over one
second to enter Set mode and then select [DISPLAY]
[8 OPENING MESSAGE] to change the setting.
In addition, you can also set the transceiver to display
the receive frequency immediately without displaying the
opening message (
see page 130).
y Turning off the Transceiver
To turn the transceiver OFF, press and hold
for over
one second.
34
Basic Operation
Performing Communication
Adjusting the Volume Level
The transceiver volume levels for the A-band and B-band are adjusted separately.
1 Press key to select the band for which the volume
level is to be adjusted.
Pressing
key each time toggles between the
A-band and B-band.
2 Rotate the VOL knob clockwise/counterclockwise to
adjust the volume level.
The [VOL] gauge moves right/left.
Supplement If no sound is heard from the speaker, press
and then adjust the volume level while listening to
white noise.
Toggling the Operating Band
Normally, both operating bands are displayed on the top
half and bottom half of the transceiver touch screen. This
is Dual band.
With one of the bands selected, change the frequency
and radio operating mode. The selected band (displayed
in black letters) is called Operating band. The other band
(displayed in gray letters) is called Sub-band.
Each time pressing
key toggles the operating band.
The desired operating band may also be selected by
touching the frequency display.
Pressing and holding for over one second displays only the operating band, this is
Mono-band.
For details on how to toggle the display by touching the LCD, see the following illustrations.
35
Basic Operation
Performing Communication
Touching the tag display
(“YAESU MUSEN CLUB
in this case) switches the
screen to the Name, Date
and Voltage display.
Touching the Name, Date
and Voltage display
switches the screen to the
tag display “YAESU
MUSEN CLUB”.
A-band
(operating
band)
B-band
A-band
B-band
(operating
band)
Press
Press and hold
for over
1 second
Press and hold
for over
1 second
or touch
sub-band.
A-band
Mono-band
B-band
Mono-band
Press
Press
36
Basic Operation
Performing Communication
Tips
On A-band, you can transmit and receive using the 144 MHz and 430 MHz Amateur radio bands.
On B-band, you can transmit and receive using the 144 MHz and 430 MHz Amateur radio bands.
In addition, the frequencies on the chart below can be received on A-band and B-band.
Chart of A-band and B-band
receive frequencies
A-band B-band
1.8 MHz - 30 MHz
(SW band)
30 MHz - 76 (88) MHz
(50 MHz band)
108 MHz - 137 MHz
(AIR band)
137 MHz - 174 MHz
(144 MHz band)
174 MHz - 222 MHz
222 MHz - 420 MHz
(INFO band (1))
420 MHz - 774(800)MHz
(430 MHz band)
470 MHz - 770 MHz
803(800)MHz - 999MHz
(INFO band (2))
Cellular Blocked USA Version
108 MHz - 137 MHz
(AIR band)
137 MHz - 174 MHz
(144 MHz band)
174 MHz - 222 MHz
222 MHz - 420 MHz
(INFO band (1))
420 MHz - 470 MHz
(430 MHz band)
470 MHz - 580 MHz
( ): EXP/European Version
— —
— —
— —
76 (88) MHz - 108 MHz
(FM BC Band)
— —
522 kHz - 1710 kHz
(AM BC Band)
— —
A-band and B-band can be received at the same time.
You can receive Amateur radio frequency while listening to the AIR band, or receive two Amateur
radio frequencies on the same frequency band at the same time (V+V/U+U: Dual frequency receive
on the same band).
37
Basic Operation
Performing Communication
Selecting a Frequency Band
The frequency band used for the A-band and B-band may be set separately. The frequency
band can be selected by following the steps below.
1 Press key to select A-band.
2 Press the key to select the desired frequency.
Tip Touch [F MW], then press the key to switch the
frequency bands in reverse order.
Available frequency bands differ depending on the band. The following frequency bands
can be used for A-band and B-band.
y Frequency bands on A-band
Short Wave Band 50 MHz bandFM BC Band AIR band 144 MHz band
174MHz to 222MHz
( ): EXP/European Version
Information
radio band (1)
430 MHz band
470MHz to 774(800)MHz
Information
radio band (2)
AM BC Band
y Frequency bands on B-band
AIR band 144MHz band 174MHz to 222MHz
Information radio band (1)
430MHz band
470MHz to 580MHz
38
Basic Operation
Performing Communication
Tips
The frequency settings from the factory are:
A-band: 144.000 MHz B-band: 430.000 MHz
In the default, Auto mode is set so that the transceiver will be automatically set to the optimal receive
mode for each frequency band.
To change the reception mode, press and hold
for over one second to switch to Set mode, then
touch [TX/RX] [1 MODE][3 RX MODE] (
see page 48).
For the relationship between frequency bands and receive frequencies, see the table on page 36.
To recall the home channel of each frequency band touch [F MW] followed by [HOME] (
see page
57).
Tuning to a Frequency
Tune to the desired frequency using either of the following methods:
y Rotate the DIAL to tune to the desired frequency
1 Press the key to switch the transceiver to VFO
mode.
2 Rotate the DIAL to tune to the desired frequency.
Rotate clockwise: The frequency increases.
Rotate counterclockwise: The frequency decreases.
Tip By touching [F MW] and rotating the DIAL, the
frequency will change in 1 MHz steps
y Entering the frequency directly using the numeric keys
1 Press the key to switch the transceiver to VFO
mode.
2 Touch the frequency displayed on the LCD.
The numeric keypad appears.
39
Basic Operation
Performing Communication
3 Enter the frequency using the numeric keys.
Example: To input 145.520 MHz
[1][4][5][5][2]
Example: To input 430.000 MHz
[4][3][ENT]
Tips
In factory settings, Auto Step mode is set so that the transceiver is automatically switched to the
optimal frequency steps for the receiver frequency.
The frequency may be changed in 1 MHz steps by touching [F MW] and rotating the DIAL (
see
page 47).
If a wrong digit is entered when entering a frequency using the numeric keys, it may be canceled by
pressing
.
In factory settings, turning the DIAL beyond the selected frequency band causes the transceiver to
switch to the next frequency band.
To change the tuning so the frequency will move repeatedly through the selected band, press and
hold
for over one second to switch to Set mode, then touch [CONFIG][21 VFO MODE] and
select “BAND” to repeatedly show frequencies on the same frequency band.
Selecting the Communication Mode
y Using AMS
This transceiver is equipped with AMS (Automatic Mode Select) which automatically
selects between 4 modes of transmission to correspond to the signal being received.
Because the transmitter is automatically adjusted to that of the other station, C4FM digital
signals and analog signals are both recognized automatically.
To utilize the AMS function, touch [MODE] to display “
* on the LCD. After receiving
the signal, “DN” of “
” will be changed according to the received signal.
*The display differs depending on the received signal.
Example of when
AMS is displayed
40
Basic Operation
Performing Communication
y Fixing the Communication Mode
To fix the transmission mode for operation, touch [MODE] to switch the communication
mode.
Touching [MODE] each time toggles the communication mode as follows.
[
(AMS)] → [DN (V/D mode)] → [VW (FR mode)] → [FM (analog)]
Operation mode Icon Description of Modes
AMS
(Automatic Mode Select)
The transmit mode is automatically selected from the 4 types,
corresponding to the received signal.
(The “DN” part of the icon differs depending on the type of the
received signal.)
By touching [TX DN], you can change the AMS function operation.
TX M: Automatically selects one of the 4 communication modes
according to the received signal. Briefly pressing PTT on
the microphone switches between digital mode and analog
mode.
TX FM: Automatically selects one of the 4 communication modes
according to the received signal. Always switches to FM
mode for transmission.
TX DN: Automatically selects one of the 4 communication modes
according to the received signal. Always switches to DN
mode for transmission.
TX VW: Automatically selects one of the 4 communication modes
according to the received signal. Always switches to VW
mode for transmission.
AUTO: Automatically selects one of the 4 communication modes
according to the received signal.
V/D Mode
(Voice/Data simultaneous
transmission mode)
DN Calls are less prone to interruptions due to detection and correction
of voice signals during digital voice signal transmission. This is the
standard mode for C4FM FDMA Digital.
Voice FR Mode
(Voice Full Rate Mode)
VW High speed data communication using entire 12.5 kHz band.
Enables high-quality voice communication.
Data FR Mode (High Speed
Data Communication Mode)
DW Digital voice data transmission using the entire 12.5 kHz band.
The transceiver automatically switches to this mode during image
transmission.
Analog FM Mode FM Analog communication using FM mode.
Effective when the signal is weak and audio is susceptible to
interruption in digital mode.
Caution
In V/D mode (“DN” on the LCD), position information is included in the radio wave during voice
communication, however, position information is not included in the Voice FR mode (“VW” on the LCD).
Transmitting/Receiving Signals
1
While pressing and holding , speak into the microphone.
Keep your mouth about 5 cm away from the microphone when you speak.
2 Release .
The transceiver returns to receive mode.
41
Basic Operation
Performing Communication
Cautions
y Use the transceiver at the minimum required transmit power level. Doing so prevents the transceiver
from overheating and saves battery power, increasing the operating time.
y Do not continue transmitting for a prolonged period. The transceiver can overheat, resulting in
malfunction or a burn injury.
y If transmission is continued for a long period, the transceiver overheats and the high temperature
protection function is activated. As a result, the transmitting power level is automatically set to Low
Power. If you continue transmitting while the high temperature protection function is active, the
transceiver will be forcibly returned to the receive mode.
y If you touch the transceiver immediately after the high temperature protection function has become
active, you may be burned. Wait for the temperature inside the transceiver to cool sufficiently before
resuming transmission.
y Do not start transmitting without attaching the antenna. The transmitter circuit can be damaged.
Tips
In FM mode, you can transmit on the 144 MHz and 430 MHz ham radio bands.
Even while receiving in AM mode, transmit will continue to be in NFM mode when pressing
.
The transmit power level may be changed by touching [F MW] followed by [TXPWR] (
see page
46).
Transmit power level settings are different when using the chargeable battery pack, or using the
alkaline battery case.
For more details, see “Turning on the Transceiver” on page 32.
If
is pressed when a frequency other than the amateur ham radio band is selected, an alarm tone
(beep) will be emitted and “ERROR” appears on the LCD, disabling transmission.
The transceiver may be set to inhibit transmit while receiving a signal. Press and hold
key
for over one second to activate Set mode, then rotate the DIAL to the setting from [CONFIG] [2
BCLO], and then select [ON].
42
Basic Operation
Listening to the Radio
Listening to the AM/FM Radio
AM broadcasts (middle wave band) and FM broadcasts can be easily received using
“Preset Memory Receiver” (
see page 65), where many major broadcast stations are
already saved to the transceiver memory. You can also tune in to the desired frequency by
rotating the DIAL or directly inputting the frequency from the numeric keypad input screen.
1 Press the key to set the A-band as the operating band.
2 Press the key to select either the “AM broadcast” or “FM broadcast” band.
3 Rotate the DIAL or display the numeric keypad input screen to tune in to the desired
frequency (
see page 38).
Tips
Broadcast stations can be saved to the memory channels ( see page 54).
To scan a broadcast radio band, set A-band to the operating band and touch [F MW] followed by
[SCAN].
When a signal is detected while scanning, a beep will sound; the transceiver will receive the signal
for 5 seconds then resume scanning.
The decimal point will flash when scanning stops.*
*You can change the scan restart time interval.
43
Basic Operation
Miscellaneous Settings
Setting Clock Time
This transceiver is equipped with an internal clock. The clock is used to display the time,
and also to turn the transceiver on or off at a specified time (timer function). Set the clock
before using the transceiver for the first time.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [CONFIG].
3 Rotate the DIAL, then touch [19 DATE & TIME ADJ].
Cursors appear and blink at the last 2 digits of the year.
4 Rotate the DIAL to select the year, then press the
key.
The cursor jumps to the month.
5 Rotate the DIAL to select the month, then press the
key.
The cursor jumps to the day.
6 Rotate the DIAL to select the day, then press the
key.
The cursor jumps to the hour.
7 Rotate the DIAL to select the hour, then press the
key.
Remark The hour appears in the 24-hour clock format.
The cursor jumps to the minute.
44
Basic Operation
Miscellaneous Settings
8 Rotate the DIAL to select the minute, then press the
key.
Tip If GPS information is received, the time will be set
automatically.
9 To activate the time signal (alarm goes off every hour on
the hour), touch [SIGNAL ON].
The checkbox will be checked.
10 Touch [OK].
The transceiver exits from Set mode.
Remark The current time appears on the LCD.
Tips
At normal temperature, the time deviation is ±30 seconds per month. It may vary depending on the
environment conditions, such as the temperature .
The transceiver is equipped with a rechargeable lithium battery dedicated for the clock. Normally,
the transceiver is powered from the battery pack. When the battery pack is detached or runs
out, the lithium battery starts operating automatically. The lithium battery can power the clock for
approximately 2 months.
When you use the transceiver for the first time or without the battery pack for a long period of time,
the accuracy of the clock may be poor. In such case, reattach the battery pack and adjust the time.
The calendar can display dates from January 1, 2000 A.D. up to December 31, 2099 A.D.
Press and hold
for over one second to enter Set mode, then select [APRS][21 GPS TIME
SET] followed by [AUTO] to display accurate time automatically.
Using the timer function enables the transceiver to automatically turn off at a specified time (
see
page 149). In addition, you can set the transceiver to turn on at a specified time (
see page 149).
Muting Audio
If the A-band and B-band are heard simultaneously during dual receive, and it is difficult
to hear the voices, the audio of the non-operating band may be muted.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [TX/RX].
45
Basic Operation
Miscellaneous Settings
3 Touch [3 AUDIO].
4 Touch [2 MUTE].
5 Rotate the DIAL to select the desired mute setting.
Select one of the following 4 options.
• OFF
• MUTE 30%
• MUTE 50%
• MUTE 100%
The higher the value for MUTE, the more the non-operating band audio is reduced.
To deactivate the muting function, select OFF.
6 Press .
The transceiver exits from Set mode.
Remark When the muting function is activated, appears on
the LCD.
Tips
Even if the muting function is activated, the voice is not muted when no signal is received on the
operating band.
46
Basic Operation
Miscellaneous Settings
Changing the Transmission Power Level
The maximum transmit power level of this transceiver is 5 W. When communicating with
another station in the immediate area, or to reduce the battery power consumption, the
transmit power level may be lowered. For power supply types and transmit power levels,
see the table shown below.
Battery type
HIGH
(High Power)
LOW3 LOW2
LOW1
USA/EXP European
Battery pack
5W 2.5W 1W
0.1W
0.05W (VHF)
0.1W (UHF)
External power supply (DC13.8V)
Battery Case (alkaline battery) Approx. 0.8W
0.05W (VHF)
0.1W (UHF)
1 Touch [F MW].
2 Touch [TXPWR].
3 Rotate the DIAL to select one of the following transmission power levels.
“HIGH”, “LOW3”, “LOW2”, “LOW1”
4 Press .
The transmit power level will be set.
Tips
The transmitter power level may be set separately for the A-band and B-band.
Use the transceiver at the minimum required transmit power level to reduce battery power
consumption.
By default, “HIGH (High power)” is selected.
47
Basic Operation
Miscellaneous Settings
Adjusting the Squelch Level
The raspy noise heard when no signal is being received may be muted (squelched). The
squelch level can be adjusted separately for two broadcasts (FM and AM) received on
the A-band and B-band.
When the squelch level is increased, the noise is more likely to be silenced, but it may
become more difficult to receive weak signals. Adjust the squelch level as required.
1 Press key to select the desired operating band.
2 Press .
3 Rotate the DIAL to adjust the squelch level.
Remarks The squelch level can be adjusted within the range
from 0 to 15.
Default: LEVEL 1.(FM radio broadcast band is LEVEL
2)
4 Press PTT.
The squelch level will be set.
Tip
While is held pressed, the squelch function will be open for
both the A-band and B-band.
Setting the Frequency Step
You can set the frequency step to a fixed value. By default, “AUTO (Step)” is selected
so that the optimum frequency step is automatically selected according to the receiver
frequency.
1 Press and hold key for over one second.
The transceiver enters Set mode.
2 Touch [CONFIG].
3 Rotate the DIAL, then touch [18 STEP].
48
Basic Operation
Miscellaneous Settings
4 Rotate the DIAL to select the desired frequency step.
Remark Selectable frequency steps are as follows:
• AUTO • 5.0KHz • 6.25KHz
• (8.33KHz) • 10.0KHz • 12.5KHz
• 15.0KHz • 20.0KHz • 25.0KHz
• 50.0KHz • 100.0KHz
It is recommended that AUTO be selected for normal operations.
Default: AUTO
5 Press .
The transceiver exits from Set mode.
Tips
For the AIR band (108 MHz to 136.991 MHz), the frequency step “8.33 kHz” can also be selected.
For bands covering 250 MHz to 300 MHz, and bands covering 580 MHz or higher, the frequency
steps “5 kHz”, “6.25 kHz”, and “15 kHz” cannot be selected.
Changing the Mode
The operating mode of the selected band may be changed.
By default, “AUTO (Auto Mode)” is set so that the typical operating mode (radio wave
type) is automatically selected according to the frequency band in use.
1 Press key for over one second.
The transceiver enters Set mode.
2 Touch [TX/RX].
3 Touch [1 MODE].
4 Touch [3 RX MODE].
The current setting will be displayed.
49
Basic Operation
Miscellaneous Settings
5 Rotate the DIAL to select the desired mode.
It is recommended that AUTO be selected for normal
operation.
Display Operation
AUTO The optimal mode is automatically selected according
to the frequency band.
NFM Only the selected band is switched to the NFM (FM
mode).
AM Only the selected band is switched to the AM mode.
6 Press .
Set mode will be canceled.
Tip
Even if AM mode is selected on a ham radio band, 144 MHz band or 430 MHz band, transmission will
continue to be in the FM mode.
Caution
The mode of the A-band AM/FM broadcast radio bands cannot be changed.
Locking Keys and Switches
To prevent accidental frequency change during operation, the keys, switches and DIAL
(except
, , , and ) can be locked.
1 Press .
[LOCK] is displayed for 1 second on the LCD.
When the lock function is activated,
always appears on
the LCD.
Remark To unlock a key or switch, press again.
[UNLOCK] is displayed on the LCD for 1 second.
Tip
To lock/unlock the operations of the DIAL and , press the key for over one second to enter Set
mode, then select [CONFIG][9 LOCK].
50
Basic Operation
Miscellaneous Settings
Attenuator (ATT) Function (except AM broadcasts and AM broadcasts)
If the remote station signal is too strong or there is a strong signal nearby disturbing you
from hearing the remote station signal, switch the attenuator to ON. When there is no
reception problem, there is no need to switch the attenuator ON.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [TX/RX].
3 Touch [1 MODE].
4 Touch [1 ANTENNA ATT].
The current setting is displayed.
5 Rotate the DIAL to select [ON].
6 Press .
The transceiver exits from Set mode.
51
Basic Operation
Miscellaneous Settings
Restoring to Defaults (All Reset)
To restore all transceiver settings and memory content to the defaults.
1 Press and hold for over one second, then turn off the transceiver.
2 While pressing , and , press .
The transceiver turns on and you hear the beep.
3 When the beep sounds, release the key.
“ALL RESET?” appears on the LCD.
4 Touch [OK].
A beep sounds and the call sign input message appears
on the LCD.
Remark To cancel resetting, touch [CANCEL].
5 Press the key.
The call sign input screen appears.
6 Input your call sign.
Switch the display between the alphabet keys and number
keys to input the call sign.
7 Press .
The call sign is set and the frequency screen appears.
Caution
When the All Reset function is performed, all data registered in the memory will be deleted. Be sure to
note the settings on paper or back up the data on a microSD memory card. For details on how to save
backup onto a microSD memory card, see “Set Mode: SD CARD Menu Operations” on page 154.
Tip
To restore only the Set Mode settings to default, while pressing and , press to turn on
the transceiver.
52
Repeater Operation
Repeater Operation
Repeater Operation
Communicating Via the Repeater
The transceiver includes an ARS (Automatic Repeater
Shift) function which enables repeater operation
automatically when setting the receiver to the
repeater frequency.
1 Set the receiver frequency to the repeater
frequency.
” or “ ” appears on the left side of the frequency
whereas “TN” and the tone frequency appear on the
right side of the frequency.
2 Begin transmitting by pressing and holding . The
transmitter will automatically be set to the programmed
offset frequency and CTCSS tone.
Tips
Touching [F MW] followed by [REV] enters the “reverse” state where the transmission frequency and
the receive frequency are temporarily reversed. This allows checking to find if direct communication
with the remote station is possible.
In the “reverse” state, “
” blinks on the LCD.
Touching [F MW] followed by [REV] again exits from the “reverse” state.
Press and hold
for over one second to enter Set mode, then configure the following repeater
settings for more convenient use.
[CONFIG][14 RPT ARS]: Deactivates the ARS function.
[CONFIG][15 RPT SHIFT]: Allows setting the repeater shift direction.
[CONFIG][16 RPT SHIFT FREQ]: Allows changing the repeater shift offset
53
Repeater Operation
Repeater Shift
The FT2DR/DE has been configured, at the factory, for the repeater shifts customary in
the country where it is sold. For the 144 MHz band, this usually will be 600 kHz, while the
430 MHz shift will be 1.6 MHz, 7.6 MHz, or 5 MHz (USA version).
Depending on the part of the band in which you are operating, the repeater shift may be
either downward (−) or upward (+), and one of these icons will appear to the right of the
display frequency on the LCD when repeater shifts have been enabled.
Automatic Repeater Shift (ARS)
The FT2DR/DE Automatic Repeater Shift feature causes the appropriate repeater shift
to be automatically applied whenever it is tuned into the designated repeater sub-bands.
If the ARS feature does not appear to be working, you may have accidentally disabled it.
To re-enable ARS:
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [CONFIG].
3 Rotate the DIAL, then touch [14 RPT ARS].
4 Rotate the DIAL to select [ON] (to enable Automatic Repeater Shift).
5 Press .
The transceiver exits from Set mode.
Tone Calling (1750 Hz)
If your transceiver is FT2DE (European version), press and hold in the press and hold
the
switch (just below the switch) to generates a 1750 Hz burst tone to access
the European repeater. The transmitter will automatically be activated, and a 1750 Hz
audio tone will be superimposed on the carrier. Once access to the repeater has been
gained, you may release the
switch, and use the switch for activating the transmitter
thereafter. If you need to access the repeaters which requires a 1750 Hz burst tone for
access by the FT2DR (USA/EXP versions), you can set the
switch to serve as a “Tone
Call” switch instead. To change the configuration of this switch, use Set Mode [CONFIG]
→ [10 MONI/T-CALL].
54
Using the Memory
Using the Memory
A Wide Variety of Memory Functions
The FT2DR/DE transceiver incorporates the following types of memory channels in
addition to the regular memory channels (numbers 001 to 900).
[Home channels] which can be recalled on each frequency band just by touching a key
(
see page 57)
Preset Receiver Memory Channels include the International VHF marine radio (57
channels) and Worldwide Wide Broadcasts (89 channels) (
see page 65)
99 (901 to 999) skip search memory channels that allow skipping unwanted frequencies
during VFO scanning (
see page 72)
50 sets of memory channels (L1/U1 to L50/U50) for programmable memory channel
scanning (PMS) (
see page 81)
The operating frequency and other operational information can be registered to each
regular memory channel, home channel, or PMS memory channel:
• Operating frequency • Memory tag • Repeater information
• Tone information • DCS information • Memory channel skip information
• Transmitter output
(The analog/digital operating mode is not registered to the memory channel)
Memory channels can be sorted and registered into memory banks according to the
intended use. The transceiver allows you to use 24 types of memory banks. A maximum of
100 memory channels can be registered in each memory bank. A name can be assigned
to each memory bank with up to 16 characters. (
see page 64)
900
899
4
3
2
1
L50/U50
L49/U49
L4/U4
L3/U3
L2/U2
L1/U1
904
903
902
901
999
998
Memory Channel Configuration of the Transceiver
Memory channels
(900 channels)
Home channels
(11 channels)
Memory banks
(24 banks)
Up to 100 memory channels can be
registered to each bank.
Skip search memory channels
(99 channels)
PMS memory channels
(50 sets)
Preset receiver memory channels
• Memory channels for short wave broadcasts
(89 channels) and international VHF (marine)
radios (57 channels)
55
Using the Memory
A Wide Variety of Memory Functions
Registering to Memory Channel
Caution
The information registered to memory channels can be corrupted by incorrect operation, static
electricity, or electrical noise. Also, it can be erased in the event of a failure or repair. Be sure to keep
a record of the settings on paper or back up the data to the microSD memory card. For details on
saving a backup onto a microSD memory card, see “Set Mode: SD CARD Menu Operations” on page
154.
The transceiver allows programming 900 memory channels (memory channel numbers
1 to 900).
1 Press the key to enter VFO mode.
2 Rotate the DIAL to tune to the frequency to be
registered to a memory channel.
3 Touch [F MW] for over one second.
The transceiver will enter Memory Channel
Registration mode, and the number of the next
available memory channel will flash on the LCD.
Remarks To cancel the memory channel registration,
press
.
To specify some other memory channel to
register the frequency, select the memory
channel by rotating the DIAL.
If the specified memory channel is unregistered,
the ( icon will be shown, and the memory
channel will flash.
If the specified memory channel is previously
registered, the ) lights up.
56
Using the Memory
A Wide Variety of Memory Functions
4 Touch [M.WRITE].
The frequency registration will initiate.
If you attempt to register a frequency to a memory
channel on which another frequency has already
been registered, “OVERWRITE?” will appear on
the LCD.
When [OK] is selected, touch [OK] to register the
frequency to the memory channel.
Once the registration is completed, the VFO
frequency will again appear on the display.
Tips
By default, 144.000 MHz is registered to the memory channel 1. It can be changed to another
frequency, but cannot deleted.
The frequency which has been registered to a memory channel can be overwritten with a new
frequency.
When registering a frequency to a memory channel, an unregistered memory channel automatically
appears.
To display the lowest unregistered memory number when registering a frequency to a memory
channel, press and hold
key for over one second to enter Set mode, and then select
[MEMORY][6 MEMORY WRITE].
To inhibit registration to all memory channels, press and hold
key for over one second to
enter Set mode, and then select [MEMORY][4 MEMORY PROTECT].
Split Memory
Two different frequencies, one for receive and another for transmit, can be registered to
a memory channel.
1 Register a receive frequency to a memory channel.
Remark See “Registering to Memory Channel” above.
2 Set a transmit frequency in VFO mode.
3 Touch [F MW] for over one second.
4 Rotate the DIAL to select the channel that the receive frequency was registered to.
5 While pressing , touch [M.WRITE].
When the memory channel to which two different
frequencies (one for receive and the other for transmit) is
recalled, @ appears on the LCD.
57
Using the Memory
A Wide Variety of Memory Functions
Recalling a Memory Channel
Recall a registered memory channel by following the steps below.
1 Press the key to enter Memory mode.
The memory channel most recently used appears on the LCD.
2 Rotate the DIAL to select the desired memory channel.
Remark Touching [F MW] and rotating the DIAL allows skipping memory channels quickly in steps
of 10 memory channels.
3 Press .
Memory mode will be exited, and the frequency selected in VFO mode will be
displayed.
Tips
Unregistered memory channels are skipped.
By default, memory channel number 1 is used as a dual receive priority memory channel, “P”
appears on the upper right corner of the priority memory channel number (
see page 96).
The data registered to a memory channel can be transferred to the VFO operating band by following
the procedure below.
Touch [F MW] for over one second. → Touch
→ Touch [V.WRITE]. → “OVERWRITE?”
appears. → Select [OK], then touch [OK] to confirm.
The transceiver may be placed into a Memory Channel Only mode, (which restricts the FT2DR/DE
operation to memory channels only), by pressing
, while pressing to turn the transceiver
on.
To cancel the Memory Channel Only mode, press
, while pressing again.
Recalling the Home Channels
1
Touch [F MW].
The function menu appears on the LCD.
58
Using the Memory
A Wide Variety of Memory Functions
2 Touch [HOME].
The home channel of the currently selected frequency band appears on the LCD.
Tips For details on the home channels displayed on the LCD, see the following table.
After selecting the desired frequency, rotating the DIAL returns the transceiver to VFO
mode.
Frequency band Frequency Frequency band Frequency
AM Band 540 kHz 174 to 222 MHz band 174.000 MHz
FM Band 76.000 (88.000) MHz Information radio band (1) 222.000 MHz
SW band 1.800 MHz 430 MHz band 446.000 (430.000) MHz
50 MHz 50.000 MHz 470 to 770 MHz band 47.000 MHz
AIR band 108.000 MHz Information radio band (2) 860.000 MHz
144 MHz band 146.520 (144.000) MHz
Returning to the Previous Frequency
1 Touch [F MW].
The function menu appears on the LCD.
2 Touch [HOME].
The frequency band selected before recalling the home channel appears on the LCD.
Changing the Home Channel Frequency
Change the home channel frequencies from the default setting.
1 Press the key to enter VFO mode.
2 Rotate the DIAL to tune in to the frequency you want to set as a home channel.
3 Touch [F MW] for over one second.
4 Touch .
5 Touch [H.WRITE].
6 “OVERWRITE?” appears.
7 Select [OK], then touch [OK] to confirm.
Overwriting completes and the home channel frequency is changed.
59
Using the Memory
A Wide Variety of Memory Functions
Clearing Memories
1
Press the key to enter Memory mode.
2 Touch [F MW] for over one second.
3 Rotate the DIAL to select the memory channel from which the data is to be cleared.
4 Touch .
5 Touch [M.DEL].
6 “DELETE?” appears.
7 Select [OK], then touch [OK] to confirm.
Remark To cancel the memory clear operation, touch
[CANCEL].
The memory data is cleared.
Remark To clear data from other memory channels, repeat
steps 2 to 7.
Caution
Data on memory channel 1 cannot be deleted.
Tip
Memories cannot be cleared from the specified priority memory channel. To clear a priority memory
channel, cancel the priority setting of the memory channel.
Restoring the Cleared Memories
The cleared memory channels may be restored:
1 Press the key to enter Memory mode.
The most recently used memory channel is displayed.
2 Touch [F MW] for over one second.
3 Rotate the DIAL to select the memory channel, to restore the memory data.
4 Touch .
5 Touch [M.REV].
The cleared data is restored to the memory channel.
Using Memory Tag
Memory name tags, such as a call sign or broadcast station name may be assigned
to the memory channels and home channels. Input a memory tag using up to 16
characters. Alphabetic characters (upper and lowercase), Numbers and Symbols may
be entered to the memory name tag.
60
Using the Memory
A Wide Variety of Memory Functions
Assigning a Name to a Memory Channel
1 Press the key to enter Memory mode.
2 Recall the memory channel to assign the name.
Tip
To assign a name to a home channel, recall the desired home channel.
3 Press and hold for over one second.
The transceiver enters Set mode.
4 Touch [MEMORY].
5 Touch [3 MEMORY NAME].
6 See “Entering Letters” on page 19 to input a memory
tag.
7 Press .
The memory tag is saved to the memory channel, and the transceiver exits from Set
mode.
61
Using the Memory
A Wide Variety of Memory Functions
Displaying the Memory Tag
During mono band operation, the tag (name) of the memory channel or home channel
can be displayed by following the procedure below.
1 Press the key to enter Memory mode.
2 Press and hold the key for over one second.
The mono-band-operation display appears, and the
name tag appears under the frequency.
The name tag also appears under the frequency when
the frequency is displayed in double-sized characters.
Tips • Touch the Name, Date, or Volt display to display the
memory tag name in double-sized characters.
Touch the display again to restore the font size to the
original.
62
Using the Memory
Using Memory Bank
The registered memory channels can be sorted according to the intended use.
The transceiver allows using up to 24 memory banks. A maximum of 100 memory
channels can be registered in each memory bank. One memory channel may also be
registered in two or more memory banks. If the data on a memory channel is edited
or updated, the data on the corresponding memory channel in the memory banks is
automatically edited or updated.
Memory banks
b1
b2
b3
b4
b5
b6
b7
b8
b9
(1–100) 144MHz band is registered.
(1–100) 430MHz band is registered.
(1–100)
(1–100) Ham radio bands are registered all together.
(1–100)
(1–100) AIR band is registered.
(1–100)
(1–100)
(1–100)
b10 (1–100)
b24 (1–100)
Memory channels
1 145.000MHz
2 145.500MHz
3 120.400MHz
4-
5 439.700MHz
6 432.800MHz
7 108.700MHz
8 -
9 -
10 -
900-
...
...
Registering to Memory Banks
1
Press the key, to enter Memory mode.
2 Rotate the DIAL to select the memory channel to
register in the memory bank.
3 Touch [F MW] for over one second.
Memory Write mode is activated.
4 Rotate the DIAL to select the memory bank (B1 to B24)
to register the memory channel.
5 Touch [M.WRITE].
The memory channel is registered in the selected
memory bank.
63
Using the Memory
Using Memory Bank
Tips
To register the preset receiver memory channels in the memory bank, see “Registering Preset
Receiver Memory Channels into Memory Banks” on page 66.
Rotating the DIAL selects the memory channels, skip search memory channels, and programmable
memory channels on the LCD in the following sequence:
1 ↔ 2 ↔ 3 ↔ ...L50 ↔ U50 ↔ BANK 1 ↔ BANK 2 ↔ ...BANK 24 ↔ 1 ↔ 2...
Memory bank channels are displayed when the DIAL is turned counterclockwise from channel [1],
or when the DIAL is rotated clockwise from channel [U50].
If the memory bank name was changed, the changed bank name appears.
appears for a memory bank in which no memory channel is registered, and appears for a
memory bank in which at least one memory channel is registered.
Recalling Memory Bank
1
Press the key, to enter Memory mode.
2 Touch [F MW].
3 Touch [BANK].
4 Press the key.
5 Rotate the DIAL to select the desired memory bank.
6 Press the key.
The memory bank to be used is determined.
7 Rotate the DIAL to select the desired memory channel in the memory bank.
Remarks To select other memory banks, repeat steps 4 to 6.
To return to the regular memory channel mode, touch [F MW] followed by [MR].
Canceling Memory Channel Registration in Memory Bank
1
To cancel the registration, recall the memory bank where the desired memory
channel is registered.
Remark For details on operations, see “Recalling Memory Bank”.
2 Rotate the DIAL to select the memory channel you want to cancel the registration.
3 Touch [F MW] for over one second.
4 Touch .
5 Touch [M.DEL].
The registration is canceled, and the display returns to the memory bank display. If
no other memory channels are registered in the memory bank, the memory bank
having the lowest number is displayed.
64
Using the Memory
Using Memory Bank
Assigning Name to Memory Bank
A name can be assigned to a memory bank using up to 16 characters.
The following types of characters can be entered:
Alphabetic characters (uppercase and lowercase characters)
• Numbers
• Symbols
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [MEMORY].
3 Rotate the DIAL, then touch [2 BANK NAME].
4 Rotate the DIAL to select a memory bank.
Select the number of the memory bank to which you want to assign a name.
5 Press and hold the key
6 Input a bank memory name (See “Entering Letters” on page 19).
7 Press .
The memory bank name is saved, and the transceiver exits from Set mode.
65
Using the Memory
Convenient Preset Receiver Memory Channels
Weather Broadcast (10 channels), International VHF Marine Radio (57 channels) and
Shortwave Broadcasts Stations (89 channels) are recorded in the preset receiver memory
channels.
• Weather Broadcast preset receiver memory channels [WX CH]
are listed on: ..................................................................................................... Page 66
The frequencies (10 channel) used for the VHF Weather Broadcast Station are regis-
tered to the dedicated preset receiver memory channels.
• International VHF Marine Radio preset receiver memory channels [INTVHF]
are listed on: ..................................................................................................... Page 67
The frequencies (57 channel) used for the international VHF (marine) radio are regis-
tered to the dedicated preset receiver memory channels.
• International World Wide Broadcast preset receiver memory channels [SW] are
listed on: .......................................................................................................... Page 68
Listen in to major broadcasts from around the world (89 channels in total).
66
Using the Memory
Convenient Preset Receiver Memory Channels
Registering Preset Receiver Memory Channels into Memory Banks
Your favorite preset receiver memory channels may be registered into a memory bank.
1 Rotate the DIAL to select the preset receiver memory channel to register into the
memory bank.
2 Touch [F MW] for over one second.
Remark To immediately cancel the registration, press .
3 Rotate the DIAL to select a memory bank to register your favorite preset receiver
memory channel.
4 Touch [M.WRITE].
The preset receiver memory channel is registered to the memory bank, and the
frequency appears on the LCD.
Recalling Preset Receiver Memory Channel to Listen to the
Weather Broadcast
The frequencies (10 channels) used for the VHF Weather Broadcast Station are registered
in the dedicated preset receiver memory channels.
1 Press the key to set the A-band as the operating band.
2 Touch [F MW].
3 Touch [P.RCVR].
Preset Receiver mode is activated.
4 Press the key to select [WX CH].
5 Rotate the DIAL to select the desired channel.
Remarks For the available Weather Broadcast channels, see the following table.
To stop reception of the international VHF radio, touch [F MW] followed by [P.RCVR]].
WX Channel Frequency List
Memory channel No. Frequency (MHz) Memory channel No. Frequency (MHz)
1 162.550 6 162.500
2 162.400 7 162.525
3 162.475 8 161.650
4 162.425 9 161.775
5 162.450 10 163.275
67
Using the Memory
Convenient Preset Receiver Memory Channels
Recalling Preset Receiver Memory Channel to Listen to the
International VHF (Marine) Radio
The frequencies (57 channels) used for the international VHF marine radio are registered
in the dedicated preset receiver memory channels.
1 Press the key to set the A-band as the operating band.
2 Touch [F MW].
3 Touch [P.RCVR].
Preset Receiver mode is activated.
4 Press the key to select [INTVHF].
5 Rotate the DIAL to select the desired channel.
Remarks For the available international VHF channels, see the following table.
To stop reception of the international VHF radio, touch [F MW] followed by [P.RCVR]].
In the event of extreme weather disturbances, such as storms and hurricanes, the NOAA (National Oceanic
and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent
weather report on one of the NOAA weather channels. You may enable the Weather Alert tone via Set Mode
option [SIGNALING] → [14 WX ALERT], if desired (See page 124).
Tips
The preset receiver memory channel cannot be rewritten with another frequency or data.
To scan the preset receiver memory channels toward higher channel numbers, touch [F MW]
followed by [SCAN]. To scan the preset receiver memory channels toward lower channel numbers,
rotate the DIAL counterclockwise until it clicks once during scanning. When a signal is received
during scanning, the scanning stops to receive the frequency for 5 seconds.
To set the transceiver operation when scanning stops, see “Setting the Receiver Operation“Setting
the Receive Operation When Scanning Stops” on page 74.
To register the International VHF Marine channels into a memory bank, follow the procedure in
“Registering Preset Receiver Memory Channels into Memory Banks” on page 66.
Frequencies of International VHF Marine radio frequencies
registered in the preset receiver memory channels
Memory channel No. Frequency (MHz) Memory channel No. Frequency (MHz)
1 156.050 160.650* 60 156.025 160.625*
2 156.100 160.700* 61 156.075 160.675*
3 156.150 160.750* 62 156.125 160.725*
4 156.200 160.800* 63 156.175 160.775*
5 156.250 160.850* 64 156.225 160.825*
6 156.300 65 156.275 160.875*
7 156.350 160.950* 66 156.325 160.925*
8 156.400 67 156.375
9 156.450 68 156.425
10 156.500 69 156.475
11 156.550 70 156.525
12 156.600 71 156.575
68
Using the Memory
Convenient Preset Receiver Memory Channels
Memory channel No. Frequency (MHz) Memory channel No. Frequency (MHz)
13 156.650 72 156.625
14 156.700 73 156.675
15 156.750 74 156.725
16 156.800 75 156.775
17 156.850 76 156.825
18 156.900 161.500* 77 156.875
19 156.950 161.550* 78 156.955 161.550*
20 157.000 161.600* 79 156.975 161.575*
21 157.050 161.650* 80 157.025 161.625*
22 157.100 161.700* 81 157.075 161.675*
23 157.150 161.750* 82 157.125 161.725*
24 157.200 161.800* 83 157.175 161.775*
25 157.250 161.850* 84 157.225 161.825*
26 157.300 161.900* 85 157.275 161.875*
27 157.350 161.950* 86 157.325 161.925*
28 157.400 162.000* 87 157.375 161.975*
88 157.425 162.025*
Remark
* indicates the frequency of the VHF marine base station. For example: if the preset receiver memory
channel 1 is selected, the base station frequency 160.650 MHz appears and @ lights up. Touching
[F MW] followed by [REV] displays the Ship Station frequency 160.650 MHz and @ lights up. The
frequency lower than the base station frequency by 4.6 MHz is the Ship Station frequency and duplex
operation may commence. To return to the base station frequency, press [F MW] followed by [REV].
Recalling Preset Receiver Memory Channels to Listen to World
Wide Broadcasts
The frequencies (89 channels) used for international worldwide broadcasting are
registered to the dedicated preset receiver memory channels.
1 Press the key to set the A-band as the operating band.
2 Touch [F MW].
3 Touch [P.RCVR].
Preset Receiver mode is activated.
4 Press the key to select [SW].
5 Rotate the DIAL to select the desired channel.
Remarks For the available world broadcast station frequencies, see the following table.
To stop reception of the world broadcast, touch [F MW] followed by [P.RCVR].
y Depending on time zone or signal strength, broadcasts may not be received.
y There are broadcast stations other than those listed below that can also be received. In addition,
the broadcast station frequency may be changed, it may be off-air or have become abolished. For
current details, please refer to a commercially available frequency list.
69
Using the Memory
Convenient Preset Receiver Memory Channels
Worldwide short wave broadcast
CH
Number
Frequency
(MHz)
Name
Broadcast Station
Name
1 6.030 VOA USA
2 6.160 VOA USA
3 9.760 VOA USA
4 11.965 VOA USA
5 9.555 CANADA Canada
6 9.660 CANADA Canada
7 11.715 CANADA Canada
8 11.955 CANADA Canada
9 6.195 BBC UK
10 9.410 BBC UK
11 12.095 BBC UK
12 15.310 BBC UK
13 6.090 FRANCE France
14 9.790 FRANCE France
15 11.670 FRANCE France
16 15.195 FRANCE France
17 6.000 DW Germany
18 6.075 DW Germany
19 9.650 DW Germany
20 9.735 DW Germany
21 5.990 ITALY Italy
22 9.575 ITALY Italy
23 9.675 ITALY Italy
24 17.780 ITALY Italy
25 7.170 TURKEY Turkey
26 7.270 TURKEY Turkey
27 9.560 TURKEY Turkey
28 11.690 TURKEY Turkey
29 9.660 VATICAN Vatican
30 11.625 VATICAN Vatican
31 11.830 VATICAN Vatican
32 15.235 VATICAN Vatican
33 5.955 NEDRLAND Netherlands
34 6.020 NEDRLAND Netherlands
35 9.895 NEDRLAND Netherlands
36 11.655 NEDRLAND Netherlands
37 5.985 CZECH Czech Republic
38 6.105 CZECH Czech Republic
39 9.455 CZECH Czech Republic
40 11.860 CZECH Czech Republic
41 9.780 PORTUGAL Portugal
42 11.630 PORTUGAL Portugal
CH
Number
Frequency
(MHz)
Name
Broadcast Station
Name
43 15.550 PORTUGAL Portugal
44 21.655 PORTUGAL Portugal
45 9.650 SPAIN Spain
46 11.880 SPAIN Spain
47 11.910 SPAIN Spain
48 15.290 SPAIN Spain
49 6.055 NIKKEI Japan (Nikkei)
50 7.315 NORWAY Norway
51 9.590 NORWAY Norway
52 9.925 NORWAY Norway
53 9.985 NORWAY Norway
54 6.065 SWEDEN Sweden
55 9.490 SWEDEN Sweden
56 15.240 SWEDEN Sweden
57 17.505 SWEDEN Sweden
58 6.120 FINLAND Finland
59 9.560 FINLAND Finland
60 11.755 FINLAND Finland
61 15.400 FINLAND Finland
62 5.920 RUSSIA Russia
63 5.940 RUSSIA Russia
64 7.200 RUSSIA Russia
65 12.030 RUSSIA Russia
66 7.465 ISRAEL Israel
67 11.585 ISRAEL Israel
68 15.615 ISRAEL Israel
69 17.535 ISRAEL Israel
70 6.045 INDIA India
71 9.595 INDIA India
72 11.620 INDIA India
73 15.020 INDIA India
74 7.190 CHINA China
75 7.405 CHINA China
76 9.785 CHINA China
77 11.685 CHINA China
78 6.135 KOREA South Korea
79 7.275 KOREA South Korea
80 9.570 KOREA South Korea
81 13.670 KOREA South Korea
82 6.165 JAPAN Japan
83 7.200 JAPAN Japan
84 9.750 JAPAN Japan
70
Using the Memory
Convenient Preset Receiver Memory Channels
CH
Number
Frequency
(MHz)
Name
Broadcast Station
Name
85 11.860 JAPAN Japan
86 5.995 AUSTRALIA Australia
87 9.580 AUSTRALIA Australia
CH
Number
Frequency
(MHz)
Name
Broadcast Station
Name
88 9.660 AUSTRALIA Australia
89 12.080 AUSTRALIA Australia
Receive Mode: AM
71
Scanning Function
Scanning Function
The transceiver supports the following three scanning functions:
VFO Scan
Memory Channel Scan
Programmable Memory Channel Scan (PMS)
VFO Scan
1 Press the key to switch the transceiver to VFO
mode.
2 Press the key to select the operating band you
want to scan.
3 Touch [F MW].
The function menu appears on the LCD.
4 Touch [SCAN].
Scanning (SCAN) starts toward higher frequencies.
72
Scanning Function
VFO Scan
Tips When a signal is received during scanning, the
decimal point blinks.
Rotate the DIAL clockwise to start scanning toward
higher frequencies.
Rotate the DIAL counterclockwise to start scanning
toward lower frequencies.
When a signal is received during scanning, a beep
sound is emitted. Then, scanning stops for 5 seconds
to monitor the frequency. When scanning stops, the
decimal point blinks and the LCD remains illuminated.
After receiving the signal for 5 seconds, scanning
resumes.
To select the range for scanning, enter Set mode
by pressing and holding the
key for over one
second, then select [SCAN] followed by [5 SCAN
WIDTH].
during scanning,
the decimal point blinks.
Canceling Scanning
To exit scanning, touch [STOP] or press .
Tips
To set the transceiver action when scanning stops, see “Setting the Receive Operation When
Scanning Stops” on page 74.
Press and hold the
key for over one second to enter Set mode, then configure the following
operating preferences settings.
[CONFIG] [3 BEEP] [SELECT]: Sets whether or not the beep sound is emitted when scanning
stops.
[CONFIG] [3 BEEP] [EDGE]: Sets whether or not the beep sound is emitted when the frequency
band edge or memory channel 01 is reached during scanning.
[SCAN][2 SCAN LAMP] Sets whether or not the LCD is illuminated when scanning stops.
Skipping Frequencies You Do Not Want to Scan (Skip Search Memory)
During VFO scan, scanning may stop at a frequency that you do not want to receive.
The unwanted frequency can be skipped by registering it to the “skip search memory
channels” in advance. Up to 99 frequencies can be saved onto the skip search memory
channels (memory channels 901 to 999).
73
Scanning Function
VFO Scan
Specifying the Frequencies You Do Not Want to Scan
1 Start VFO scanning.
Start VFO scanning referring to “VFO Scan” on page 71.
2 When scanning stops at a frequency you do not want to
receive, touch [F MW] for over one second.
The number of the next unused skip search memory
channel will blink.
Tip A different skip search memory channel may be specified by
rotating the DIAL.
3 Touch [M.WRITE].
After completing registration to the skip memory channel,
scanning resumes.
Tips Follow the procedure below to register the frequencies you do not want to scan to the “skip
search memory channels” in advance.
1 In VFO mode, tune in to the frequency you do not want to scan.
2 Touch [F MW] for over one second.
3 Rotate the DIAL to select the desired skip search memory channel (901 to 999).
4 Touch [M WRITE].
Deleting the Frequency Registered to the Skip Search Memory Channel
Frequencies can be removed from the skip search memory channels by following the
procedure below. Once the frequencies are removed from the skip search memory
channels, they can then be scanned.
1 Press the key to enter Memory mode.
2 Touch [F MW] for over one second.
3 Rotate the DIAL to select the skip search memory channel (901 to 999) that is to be
cleared.
74
Scanning Function
VFO Scan
4 Touch .
5 Touch [M.DEL].
[DELETE OK?] appears on the LCD.
6 Select [OK], then touch [OK] to confirm.
TOP画面!A1
The frequency is removed from the skip search memory channel.
Tip To remove other frequencies from the skip search memory channels, repeat steps 2 to 6.
Tip
Restoring the deleted Frequency to the Skip Search Memory Channel
If you have not registered a new frequency to the same memory channel, you can restore the deleted
frequency by repeating steps 1 through 4, then touching [M.REX].
Setting the Receive Operation When Scanning Stops
When scanning stops, one of the following three receiving options may be chosen:
(1) The signal is received for a specified period of time, and then scanning resumes. The
scan resume time may be set from 2 to 10 seconds at 0.5 second intervals.
(2) The signal is received and [BUSY] appears on the LCD until the signal fades out. Two
seconds after the signal fades out, scanning resumes.
(3) Scanning stops and the current frequency is received. [HOLD] appears on the LCD.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
75
Scanning Function
VFO Scan
2 Touch [SCAN].
3 Touch [4 SCAN RESUME].
4 Rotate the DIAL to select [SCAN], then press the key.
5 Rotate the DIAL to select the desired reception method from [2 SEC TO 10 SEC
(0.5SEC STEP)], [BUSY] and [HOLD].
6 Press .
The reception method is set and the transceiver exits from Set mode.
Tips
The reception method selected here is applied to [VFO Scanning], [Programmable Memory Channel
Scanning] and [Memory Channel Scanning].
The scanning restart time after BUSY (duration of signal reception) can be changed by selecting the
Set mode option [SCAN][3 SCAN RE-START].
76
Scanning Function
Memory Channel Scanning
The memory channel frequencies may be scanned in the order of the memory channel
numbers.
1 Press the key to enter Memory mode.
2 Rotate the DIAL to select the memory channel to begin memory scanning from.
3 Touch [F MW].
The function menu appears on the LCD.
4 Touch [SCAN].
Scanning (SCAN) begins and progresses toward higher memory channel numbers.
When a signal is received, the decimal point blinks.
Tips Rotate the DIAL clockwise to start scanning toward higher
frequencies.
Rotate the DIAL counterclockwise to start scanning toward
lower frequencies.
When a signal is received during scanning, scanning stops
for 5 seconds to monitor the signal on the frequency of the
signal.
When scanning stops, the decimal point blinks and the LCD
remains illuminated.
After receiving the signal for 5 seconds, scanning resumes.
Press
to cancel scanning.
Tips
When a memory channel is recalled, the regular memory channels (memory channel numbers 1-900)
are scanned.
When a memory bank is recalled, only the memory channels in the memory bank are scanned.
To set the transceiver operation when scanning stops, see “Setting the Receive Operation When
Scanning Stops” on page 74.
Press and hold the
key for over one second to enter Set mode, then configure the following
operating preference settings.
[CONFIG] [3 BEEP] [SELECT]: Sets whether or not the beep sound is emitted when scanning
stops.
[CONFIG] [3 BEEP] [EDGE]: Sets whether or not the beep sound is emitted when the
frequency band edge or memory channel 01 is reached during scanning.
[SCAN][2 SCAN LAMP]: Sets whether or not the LCD is illuminated when scanning stops.
[SCAN][5 SCAN WIDTH]: Sets the range of frequencies or channels to be scanned.
When a signal is received,
the decimal point blinks.
77
Scanning Function
Memory Channel Scanning
Specifying Skip/Selected Memory Channels
Two types of memory channels may be designated, “skip memory channels” and “specified
memory channels” for effective memory channel scanning.
Skip memory channels: You can specify a memory channel you do not want to scan
during memory channel scanning. Alternatively, you can specify that only designated
memory channels are scanned during memory scanning.
1 Press the key to enter Memory mode.
2 Rotate the DIAL to show the memory channel to register as a skip memory channel or
specified memory channel.
3 Press and hold the key for over one second.
The transceiver enters Set mode.
4 Touch [MEMORY].
5 Touch [5 MEMORY SKIP].
6 Rotate the DIAL to select [SKIP] or [SELECT].
To register as a skip memory, select [SKIP].
To register as a specified memory, select [SELECT].
78
Scanning Function
Memory Channel Scanning
7 Press .
The transceiver exits from Set mode.
Tips When the channel is registered as a skip memory, lights up.
When the channel is registered as a specified memory,
blinks.
To cancel the skip memory or specified memory setting, select [OFF] in step 6. The
on the
LCD turns off and the setting is canceled.
Skip memory
[SKIP]
Specified
memory
[SELECT]
Rotate the DIAL
clockwise
[OFF]
Scanning Only the Specified Memory Channels
1 Press the key to enter Memory mode.
2 Select the memory channel registered as a specified memory channel.
3 Touch [F MW].
The function menu appears on the LCD.
4 Touch [SCAN].
Tips Rotate the DIAL clockwise to start scanning toward higher frequencies
Only the memory channels registered as the specified memory channels are scanned.
When a signal is received during scanning, a beep sound is emitted. Scanning stops for 5
seconds to monitor the cannel frequency.
When scanning stops, the decimal point blinks and the LCD remains illuminated.
After receiving the signal for 5 seconds, scanning resumes.
Press
to cancel scanning.
To select the range for scanning, enter Set mode by pressing and holding the
key for
over one second, then select [SCAN] followed by [5 SCAN WIDTH].
79
Scanning Function
Memory Channel Scanning
Scanning the Memory Bank
Only the memory channels in the recalled memory bank can be scanned.
1 Press the key to enter Memory mode.
2 Touch [F MW].
3 Touch [BANK].
4 Press the key.
5 Rotate the DIAL to select the desired memory bank from
BANK 1 to BANK 24.
6 Press the key.
7 Touch [F MW].
8 Touch [SCAN].
Tips Scanning is performed toward the higher memory channel numbers.
Rotate the DIAL clockwise: Scanning is performed toward the higher memory channel numbers.
Rotate the DIAL counterclockwise: Scanning is performed toward the lower memory channel
numbers.
When a signal is received during scanning, scanning stops for 5 seconds and this frequency is
received.
When scanning is suspended, the decimal point blinks and the LCD stays lit.
After receiving the frequency for 5 seconds, scanning resumes.
To stop scanning, press
.
You can select the range for scanning by pressing and holding the
key for over one
second to enter Set mode, then selecting [SCAN][5 SCAN WIDTH].
Memory Bank Link Scanning
During regular memory bank scanning, only the
memory channels assigned to the recalled memory
bank are scanned. During memory bank link scanning,
you can scan memory channels registered in two or
more banks you specified in advance.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [MEMORY].
3 Touch [1 BANK LINK].
4 Rotate the DIAL to select the memory bank for which you want to perform bank link
scanning.
5 Press the key.
is displayed for the selected memory bank and is displayed for unselected
memory bank.
6 Repeat steps 4 and 5 to select other memory banks.
7 Press .
The transceiver exits from Set mode.
BANK 1
BANK 10
BANK 24
80
Scanning Function
Memory Channel Scanning
8 Press the key to enter Memory mode.
9 Touch [F MW].
10 Touch [BANK].
11 Press the key.
12 Rotate the DIAL to select the memory bank to begin memory scanning from.
The memory bank number is changed from [B] to [b] and
the bank link scanning is activated.
13 Press the key.
The memory banks for which you perform memory bank
link scanning are determined.
14 Touch [F MW].
The function menu screen appears.
15 Touch [SCAN].
Tips Scanning is performed toward the higher memory
channel numbers.
Rotate the DIAL clockwise: Scanning is performed
toward the higher memory channel numbers.
Rotate the DIAL counterclockwise: Scanning is performed toward the lower
memory channel numbers.
When a signal is received during scanning, scanning stops for 5 seconds and
this frequency is received.
When scanning is suspended, the decimal point blinks and the LCD stays lit.
After receiving the frequency for 5 seconds, scanning resumes.
To stop scanning, touch [STOP] or press .
You can select the range for scanning by pressing and holding the key for
over one second to enter Set mode, then selecting
[SCAN][5 SCAN WIDTH].
y Canceling Bank Link Scanning
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [MEMORY].
3 Touch [1 BANK LINK].
4 Rotate the DIAL to select the memory bank.
5 Press the key.
The memory bank display is changed from to and the bank link scanning is
deactivated.
6 Repeat steps 4 and 5 to select other memory banks.
7 Press .
The transceiver exits from Set mode.
The memory bank number is
changed from [B] to [b]
81
Scanning Function
Programmable Memory Channel Scan (PMS)
Registering to the Programmable Memory Channels
50 sets of PMS memory channels (L1/U1 to L50/U50) are available.
To specify a range of frequencies to scan, register the lower limit frequency to a memory
channel L1 to L50 and the upper limit frequency to a memory channel U1 to U50. Make
sure to use the corresponding numbers for the lower and upper limit memory channels.
PMS memory channels (L1/U1 to L50/U50) are listed after memory channel 999. Pressing
the
key advances the memories at 100-channel increments.
For details on registering frequencies to the memory channels, see “Registering to
Memory Channel” on page 55.
Cautions
y If the upper and lower limit frequencies are set in different steps, the scan width must be 100 kHz or
more.
y The lower and upper limit memory channels must be within the same frequency band. Programmable
memory channel scanning does not function if the frequency bands are different.
Performing Programmable Memory Channel Scan
The programmable memory channel scan allows setting a specified frequency range
within the same frequency band.
1 Press the key to enter Memory mode.
2 Recall the PMS memory channel to which the lower limit or upper limit of the frequency
is registered.
3 Touch [F MW].
The function menu appears on the LCD.
4 Touch [SCAN].
Programmable memory channel scanning starts.
During scanning, “PMS” and “P*” appear.
Tips Rotate the DIAL clockwise to start scanning toward higher
frequencies.
Rotate the DIAL counterclockwise to start scanning toward
lower frequencies.
When a signal is received during scanning, scanning stops
for 5 seconds to receive the signal on frequency.
When scanning stops, the decimal point blinks and the LCD
remains illuminated.
After receiving the signal for 5 seconds, scanning resumes.
Touch [STOP] or press
to cancel scanning.
After scanning is canceled, press the
key twice to
return to VFO mode.
The decimal point blinks.
82
Scanning Function
Programmable Memory Channel Scan (PMS)
Tips
When a skip memory channel (see page 77) is registered to [L] or [U], or when the lower/upper
limit frequency is not properly registered, program memory channel scanning does not function.
Press and hold the
key for over one second to enter Set mode, then configure the following
operating preference settings.
[CONFIG] [3 BEEP] [EDGE]: Sets whether or not the beep sound is emitted when the
frequency band edge or memory channel 01 is reached during scanning.
[SCAN][2 SCAN LAMP]: Sets whether or not the LCD is illuminated when scanning stops.
83
Digital Group Monitor Function
Digital Group Monitor Function
Using the Digital GM Function
What is the GM function?
The Digital GM (Group Monitor) function automatically checks on the air to find if there
are other transceivers operating with the GM function on the same frequency within
communication range. When other GM stations are detected, the direction, distance,
and other information for each detected call sign is displayed on the LCD. This allows
immediately checking the distances from the group members within the communication
range and other group members.
Additionally, the GM function facilitates sending messages and images to the group
members.
Caution
The GM function does not function in analog mode or on band B. Before activating GM function,
Touch [MODE] to switch to the AMS (Auto Mode Select Function) or digital mode.
Tip
The GM function does not operate in analog mode. Before activating GM function, Touch [MODE] to
switch to the AMS (Auto Mode Select Function) or digital mode.
Standard Operation of the GM Function
There are two methods of using the Digital GM function.
Display all stations (up to 24 stations) operating with the GM function.
Register IDs of friends in a group and display only registered members using the GM
function.
Displaying All Stations (up to 24 Stations) Operating with the GM
Function
1
Set the group operating frequency on band A.
2 Press the key.
The group list appears.
3 Touch [ALL].
The ID, distance, and direction of all stations (up to 24)
within the communication range operating with the GM
function on the set frequency are displayed.
If there are 6 stations or more, rotate the DIAL to scroll
through the displayed list.
When the GM function is active, you can confirm
whether or not other stations are within communication
range, and their position information with the direction
and distance from your transceiver (see the following
illustration).
84
Digital Group Monitor Function
Standard Operation of the GM Function
Direction
Distance
Example of display when ALL is selected
In
range
Out
of range
Registering IDs of Friends in a Group and Displaying Only
Registered GM Users
Create a group with a name such as [Touring] or [Camp] and display only members
registered to that group.
Group name
Example of display when GROUP is set
For details on how to setup a group and register members to it, refer to the GM Function
Instruction Manual which is available on the Yaesu website.
Deactivating the GM Function
While operating with the GM function, press the key.
The GM function is exited and the transceiver returns to the previous operating status.
Tip
With the GM function, messages and images can be transmitted between members.
For details, refer to the GM Function Instruction Manual which is available on the Yaesu website.
85
Using the APRS / WIRES-X Functions
Using the APRS / WIRES-X Functions
The APRS (Automatic Packet Reporting System) Function
The FT2DR/DE uses a GPS receiver to acquire and display its position location
information. APRS is a communication system that transmits the position information,
data and messages, using the format developed by Bob Bruninga WB4APR.
Upon receiving an APRS report from a remote station, the direction and distance to the
remote station from your station, the speed of the remote station, and other data sent by
the remote station may be displayed on the LCD of your transceiver.
Example of display when
an APRS signal is received
Setting several station parameters, such as the call sign and symbol are required before
using the APRS function (initial settings).
For details, refer to the APRS Function Instruction Manual which is available on the Yaesu
website.
What is the WIRES-X Function?
The WIRES-X is a system that connects to other users via the Internet. This function
enables users to communicate with other users regardless of the distance.
For details, refer to the separate WIRES-X Instruction Manual which is available on the
Yaesu website.
86
Using the GPS Function
Using the GPS Function
The GPS Function
GPS (Global Positioning System) is a space-based satellite navigation system that
provides location and time information anywhere on the earth. It was developed by the
U.S. Department of Defense as a military system. When the GPS receiver acquires
signals from 3 or more (of about 30) GPS satellites orbiting at an altitude of about
20,000 km, it can calculate and display its current position (latitude, longitude, and
altitude) within a tolerance of several meters. In addition, GPS can receive the exact
time from the satellite onboard atomic clock.
Activating the GPS Function
Activating the GPS function enables the transceiver to automatically obtain the internal
clock setting, and your location information setting from the GPS data.
To activate the GPS function, follow the procedure below.
Tip
The default setting is ON.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [APRS].
3 Rotate the DIAL, then touch [20 GPS POWER].
4 Rotate the DIAL to select [GPS ON]
5 Press .
The GPS function is activated, and the transceiver exits from Set mode.
87
Using the GPS Function
Activating the GPS Function
Tips
Your position information provided by GPS can be registered to 10 memory channels (P1 to P10).
For details, refer to the APRS Function Instruction Manual. The registered position information can
be set as the position of your station.
When the GPS function is active, the power consumption increases by about 30 mA. As a result,
the battery life is reduced by about 20% compared to when the GPS function is deactivated.
To use the GPS function during APRS operation, be sure to enter Set mode by pressing and holding
the
key for over one second, then set [APRS][24 MY POSITION] to [GPS].
88
Using the GPS Function
Method of Positioning by GPS
Displaying Position Information of Remote Stations in Digital Mode
With V/D mode of the C4FM digital, the GPS position information is transmitted
simultaneously with voice signals; therefore the direction and position of the remote
station can be displayed in real-time even while communicating.
For details, see “Real-Time Navigation Function” on page 93.
Tip
Even if the GPS function of your station is set to OFF, the position information of the remote station
can be displayed in V/D mode.
Caution
When the GPS function is not active, the remote station cannot display the position information for
your station.
About Positioning by GPS
“Positioning” refers to calculation of your current position from the satellite orbit
information and radio propagation time. At least 3 satellites need to be acquired
for successful positioning. If positioning fails, move away from buildings as far as
possible and stand in an area with open sky.
About errors
The measurement environment may result in positioning errors of several hundred
meters. Under favorable conditions, positioning can be performed successfully using
only three satellites. However, under the following poor conditions, the positioning
accuracy can decrease or positioning can fail.
• Between tall buildings
• Narrow paths between buildings
• Indoors or in close proximity to large buildings
• Under elevated roads or high voltage power lines
• Between trees such as in forests or woods
• Inside a tunnel or underground
• Through heat reflective glass
Areas with strong magnetic fields
● When not in use for a long time
When using the GPS functions for the first time after purchase, or when it has been
unused in a while, a few minutes may be required to acquire the satellites. Also,
if the GPS function has been turned off for several hours, a few minutes may be
required to search for satellites.
89
Using the GPS Function
Method of Positioning by GPS
Saving GPS Information (GPS Log Function)
The GPS position information can automatically be saved periodically onto a microSD
memory card. Using the saved data, tracks can be displayed on commercially available
map software*.
* Technical support for the map software is not provided by YAESU.
1 See “Activating the GPS Function” on page 86, and activate the GPS function.
2 Press the key for over one second.
The transceiver enters Set mode.
3 Touch [CONFIG].
4 Touch [6 GPS LOG].
5 Rotate the DIAL to select the GPS data logging interval.
The selectable setting values are as follows. When OFF is set, the position
information is not saved.
OFF / 1 sec / 2 sec / 5 sec / 10 sec / 30 sec / 60 sec
6 Press .
The GPS log function is activated, and the transceiver exits from Set mode.
Tip
The position information is saved periodically unless “OFF” is selected in step 5 (shown above) or the
power of the transceiver is turned off.
Reselecting the GPS data logging interval in step 5 or turning on the transceiver again, begins saving
the GPS data under a different file name.
90
Using the GPS Function
Method of Positioning by GPS
Checking Tracks on Your PC
1
Turn off the transceiver.
2 Remove the microSD memory card from the transceiver.
3 Connect the microSD memory card to your PC using a commercially available
memory card reader.
4 Open the “FT2D” folder in the microSD memory card.
5 Open the “GPSLOG” folder.
The data is saved as “GPSyymmddhhmmss.log”.
The [yymmddhhmmss] part of the name consists of year (yy), month (mm), day (dd),
hour (hh), minute (mm), and second (ss).
Tips
• Tracks can be displayed on the map by importing the data to commercially sold map software.
• For information on importing, please refer to the operation manual for the map software you use.
91
Using the GPS Function
GPS Screen Information and Operation
Activating the GPS function displays the following information on the LCD.
Displays the satellite azimuth and elevation angles. Displays in North-up mode.
Displays the date and time.
Displays the current speed.
Displays the satellite number and reception level.
Displays the latitude on the upper side of the screen whereas displays the longitude
on the lower side of the screen.
The current position appears using north (N) or south (S) latitude.
Display format: X DD° MM. MMM
X: X=N: North latitude, X=S: South latitude, DD: Degree, MM:MMM Minute
Example: N 35° 38.250 (35 degrees, 38 minutes, 15 seconds north latitude)
The current position appears using east (E) or west (S) longitude.
Display format: X DDD° MM. DMMM
X: X=E: East longitude, X=W: West longitude, DDD: Degree, MM:MMM Minute
Example: E 139° 42.500 (139 degrees, 42 minutes, 30 seconds east latitude)
Displays the altitude of the current position “ALTI xxxxm”.
Example: ALTI 20m
Displaying the GPS Information
Follow the steps below to display the GPS information.
1 Press the key.
Displays the navigation screen.
2 Touch the compass on the screen.
The GPS data is displayed.
92
Using the GPS Function
GPS Screen Information and Operation
Tips
The GPS data units for position, speed and altitude may be changed by pressing and holding the
key for over one second to enter Set mode, then select [APRS][22 GPS UNIT].
When the GPS function is used, the accurate time and date are obtained from GPS and shown on
the LCD in 24-hour format. This time data is displayed on the GPS and APRS screens.
The geodetic system datum (WGS-84 / Tokyo) of the built-in GPS unit may be changed by selecting
[APRS][19 GPS DATUM] in Set mode. However, since APRS uses the geodetic system of
WGS-84, it is recommended not to change it.
The time zone may be set at 30-minute increments by pressing and holding the
key for over
1 second to enter Set mode, then selecting [APRS][28 TIME ZONE] (the default setting: UTC
0:00).
When the GPS function is active, the power consumption increases by about 30 mA. As a result,
the battery life is reduced by about 20% compared to when the GPS function is deactivated.
The position information obtained from an external GPS device may be used by pressing and
holding the
key for over one second to enter Set mode, then selecting [APRS][17 COM
PORT SETTING] and then setting [INPUT] to [GPS]. In this case, the data from the internal GPS
will be ignored.
When using an external GPS device, move it away from the transceiver to reduce interference.
93
Using the GPS Function
Smart Navigation Function
There are 2 methods of navigation with the Smart Navigation function.
Real-time navigation function
Backtrack function
Caution
Before using the smart navigation function, press and hold the key for over one second to
enter Set mode, then from [DISPLAY][1 TARGET LOCATION], select [COMPASS].
Real-Time Navigation Function
GPS position information and voice signals are simultaneously transmitted in the V/D
mode of C4FM digital. For this reason, the position and direction of the remote station
can be displayed in real time even during communication.
1 Press the key.
The navigation screen appears.
2 Touch [YR].
The distance and direction to the remote station operating on the same frequency in
the V/D mode are displayed.
Distance to
remote station
Direction display
3 Press the key.
The screen returns to the normal frequency display.
Backtrack Function
By registering the point such as the departure point in advance, the distance and
direction to the registered point from your current position can be displayed in real time.
Registering Your Current Position (Departure Point) (up to 3 Positions can Be Registered)
1 Press the key.
The back track screen appears.
94
Using the GPS Function
Smart Navigation Function
2 Touch [MY].
Your location information is displayed.
3 Touch [MEM].
[], [L1] and [L2] blink.
4 Touch one of the blinking indicators to which you want to
register the position information.
The location information is registered with the selected
indicator, and the screen returns to the back track
screen.
5 Press the key.
The screen returns to the normal frequency display.
Using the Back Track Function
1 Press the key.
The back track screen appears.
2 Touch the indicator (“”, “L1” or “L2”) to which you want to register the location
information for back tracking.
95
Using the GPS Function
Smart Navigation Function
The registered position (departure point) is in the
direction of the arrow within the circle. Follow the arrow
so that the arrow stays pointing up on the screen.
3 Press the key.
The screen returns to the normal frequency display. To confirm the position again,
press the
key to display the back track screen.
Description of the BACK TRACK Function Screen
Distance to the registered position
Registered position indicators
Direction to the registered position
96
Convenient Functions
Convenient Functions
Dual Receive (DW) Function
The transceiver is equipped with the following 3 types of Dual Receive Functions:
VFO Dual Receive
Memory Channel Dual Receive
Home Channel Dual Receive
The transceiver checks signals over the frequency registered to the selected memory
channel (Priority Memory Channel) once approximately every 5 seconds. When the
transceiver detects signals, it starts signal reception on the selected memory channel.
While receiving a signal on the frequency registered to a priority memory channel,
pressing
disables the Dual Receive function and allows transmission over the same
frequency.
Example: Checking the priority memory channel “90” (446.500 MHz), while receiving
“146.520 MHz”
Frequency being received
The transceiver monitors signals on
the frequency registered to the Priority
Memory Channel “90” (446.500 MHz),
once approximately every 5 seconds.
When the transceiver receives a signal
on the frequency registered to the
priority memory channel “90”, dual
reception stops and signal receiver
switches to “90” (446.500 MHz).
97
Convenient Functions
Dual Receive (DW) Function
VFO Dual Receive
VFO mode → Priority memory channel
1 Press the key to enter Memory mode.
2 Touch [F MW] for over one second.
The memory registration mode is enabled, and the channel number blinks.
3 Rotate the DIAL to select the desired memory channel.
4 Touch [PRI.CH].
The memory channel to preferentially receive
(Priority Memory Channel) is selected. The “P”
appears on the LCD.
5 Press the key to enter VFO mode.
6 Select the frequency you want to constantly monitor.
7 Touch [F MW].
8 Touch [DW].
The Dual Reception starts and “VDW” appears on
the LCD.
9 Touch [STOP].
The Dual Reception is canceled.
98
Convenient Functions
Dual Receive (DW) Function
Memory Channel Dual Receive
Memory channel → Priority memory channel
1 Press the key to enter Memory mode.
2 Touch [F MW] for over one second.
The memory registration mode is enabled, and the channel number blinks.
3 Rotate the DIAL to select the desired memory channel.
4 Touch [PRI.CH].
The memory channel to preferentially receive (Priority Memory Channel) is selected.
The “P” appears on the LCD.
5 Select the memory channel you want to constantly receive.
6 Touch [F MW].
7 Touch [DW].
The HOME Channel Dual Reception starts and “MDW”
appears on the LCD.
8 Touch [STOP].
The Memory Channel Dual Receive is canceled.
Home Channel Dual Receive
Home channel → Priority memory channel
1 Press the key to enter Memory mode.
2 Touch [F MW] for over one second.
The memory registration mode is enabled, and the channel number blinks.
3 Rotate the DIAL to select the desired memory channel.
4 Touch [PRI.CH].
The memory channel to preferentially receive (Priority Memory Channel) is selected.
The “P” appears on the LCD.
5 Touch [F MW].
The function screen appears.
99
Convenient Functions
Dual Receive (DW) Function
6 Touch [HOME].
The HOME channel is recalled.
7 Touch [F MW].
8 Touch [DW].
The HOME Channel Dual Receive starts and “HDW”
appears on the LCD.
9 Touch [STOP].
The HOME Channel Dual Receive is canceled.
Tips
The Priority Memory Channel is set to the Memory Channel number 1 by default.
Press and hold the
key for over one second to enter Set mode, then configure the following
settings for more convenient use.
[SCAN][1 DW TIME]: The time interval for monitoring the Priority Memory Channel can be
changed.
[SCAN][4 SCAN RESUME]: The resumption conditions for Dual Receive can be changed.
The combination of the frequency bands and modes for the Priority Memory Channel and the
frequency for constant signal reception can be freely changed.
100
Convenient Functions
AF-DUAL Receive Function (Receiving Signals on Other
Frequency Channels While Listening to Broadcast Radio)
The AF-DUAL Receive Function allows reception of a radio broadcast during standby
reception of A-band or B-band frequency (or frequency registered to a memory
channel). When standby reception is active, no audio is heard on the standby frequency,
however if a voice signal is detected, the reception of the broadcast radio will be
paused, and the receiver frequency will be heard.
Dual Receive (
see page 96) is a similar function. When using the Dual Receive
function, every time the transceiver checks for a signal on the specified memory
channel during radio reception, the radio reception is interrupted (approximately every 5
seconds). When using the AF-DUAL Receive Function, the radio reception is interrupted
only when there is a calling signal from another transceiver.
Listening to a Radio Broadcast Using the AF-DUAL Receive
Function
1
Set the A-band or B-band frequency (or Memory Channel/Home Channel) for
standby receive during broadcast radio reception.
Tips You can listen to the radio while scanning the standby receive signal frequencies.
You can listen to the radio while monitoring the standby receive signal frequency in dual
receive mode.
2 Press the key to set the A-band to the
operating band.
3 Touch [F MW].
The function screen appears.
4 Touch [A.DUAL].
The AF-DUAL function is activated.
101
Convenient Functions
AF-DUAL Receive Function (Receiving Signals on Other Frequency Channels While Listening to Broadcast Radio)
5 Press the key to select [AM] or [WFM].
Pressing the
key each time switches between the AM broadcast (middle
wave band) and FM broadcast.
On the LCD, AM (AM broadcast) or WFM (FM
broadcast) is displayed.
6 Rotate the DIAL to tune to the frequency of the broadcast station.
Tips
For broadcast station frequencies, refer to “Worldwide short wave broadcast” on page 69 or a
commercially sold frequencies list.
The AF-DUAL receive function can also be used for a radio frequency registered to a memory bank.
Pressing
during radio reception allows receiving the standby frequency.
While listening to the radio using the AF-DUAL function, in standby receive mode, the transceiver
cannot simultaneously receive broadcasts on the AM frequency (middle wave band) on either the
band-A or band-B, and FM frequency.
To disable the AF-DUAL Function, touch [F MW] followed by [A.DUAL].
The frequency (memory channel) in receive standby appears on the LCD.
Setting the Resumption Time of Radio Reception
While receiving a radio broadcast, the ham radio band (A-band or B-band) can be
monitored in standby receive mode. After losing the receive signal or completing
transmission, broadcast reception can be resumed.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
102
Convenient Functions
AF-DUAL Receive Function (Receiving Signals on Other Frequency Channels While Listening to Broadcast Radio)
2 Touch [TX/RX].
3 Touch [3 AUDIO].
4 Touch [3 RX AF DUAL].
5 Rotate the DIAL to select the time from one of the following options for receiving
radio broadcast simultaneously.
Transmission and reception for 1 second to 10 seconds/HOLD (Fixed)/
transmission for 1 second to 10 seconds
Remark The default setting: transmission and reception for 2 seconds
Display Operation
Transmission and
reception: 1 second
to 10 seconds
In standby receive mode, while receiving a radio broadcast using the AF-
DUAL Receive function, the ham radio stand by A-band or B-band can be
received. Set the time to resume broadcast reception after losing the ham
band received signal or completing a transmission. For example, set the
time to 5 seconds to resume broadcast reception in 5 seconds after ham
band reception (or transmission) ends.
Fixed While receiving a radio broadcast using the AF-DUAL Receive function, the
ham radio band (A-band or B-band) can be monitored in standby receive
mode. If a ham band signal is received, the transceiver continuously
receives the ham band frequency.
Transmission: 1
second to 10 seconds
While receiving a radio broadcast using the AF-DUAL Receive function,
the ham radio band (A-band or B-band) can be received in standby
receive mode. When the set resume time has passed since the transceiver
completed the transmission, the transceiver returns to broadcast receive
mode. If a ham band signal is received before broadcast receive is
resumed, the AF-DUAL Receive function is ended and ham band receive is
restored.
6 Press .
The radio broadcast reception time is set, and the transceiver exits the Set mode.
103
Convenient Functions
Using the DTMF Function
DTMF (Dual Tone Multi Frequencies) are the tone signals sent to make telephone calls,
or control repeaters and network links. Up to 10 registers of 16-digit DTMF tone codes
can be stored as telephone numbers to make calls through the public telephone network
using a phone patch.
Setting the DTMF Memory
1
Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [5 DTMF SELECT].
4 Rotate the DIAL to select the desired channel (1 to 10) to
register the DTMF code, then press the
key.
104
Convenient Functions
Using the DTMF Function
5 Input the DTMF code using the numeric keypad.
Tip Up to 16 characters (including symbols) can be input as a
DTMF code.
6 Press .
The DTMF code is set, and the transceiver exits from Set mode.
Transmitting the Registered DTMF Code
1
Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [4 DTMF MODE].
4 Rotate the DIAL to select [MODE], then press the key.
5 Rotate the DIAL to select [AUTO].
6 Press .
The auto dialer is enabled.
7 Press .
Displays [DTMF].
8 While pressing and holding , touch [DTMF].
Displays the numeric keypad screen.
9 Use the numeric keypad to input the channel number of the DTMF memory you want
to transmit.
Tips The registered DTMF code is transmitted.
The transmitted DTMF audio can be heard from the speaker.
10 Release .
Even after releasing
, the transmission continues until the DTMF code
transmission is completed.
105
Convenient Functions
Using the DTMF Function
Manually Transmitting the DTMF Code
1
Press and hold the key for over one second.
The transceiver enters the Set mode.
2 Touch [SIGNALING].
3 Touch [4 DTMF MODE].
4 Rotate the DIAL to select [MODE], then press the key.
5 Rotate the DIAL to select [MANUAL].
6 Press .
The transceiver is ready for transmitting the DTMF code manually.
7 Press .
[DTMF] appears on the LCD.
8 While pressing , touch [DTMF].
The numeric keypad appears.
9 Use the numeric keypad to input the DTMF code.
Tips The registered DTMF code is transmitted (Refer to the following table).
• The transmitted DTMF sound can be heard from the speaker.
10 Release .
Even after releasing
, the transmission continues until the DTMF signal
transmission is completed.
Tip
The DTMF code is a combination of 2 frequencies.
1209Hz 1336Hz 1477Hz 1633Hz
697Hz 1 2 3 A
770Hz 4 5 6 B
852Hz 7 8 9 C
941Hz
0 # D
106
Convenient Functions
Spectrum Analyzer with Signal Strength Graph
Band Scope Function
The Spectrum Analyzer presents a view of operating activity on channels above and
below the current main band operating frequency as the center (marked with ▼).
1 Rotate the DIAL to tune in to the desired center frequency.
2 Touch [F MW].
Touch [SCOPE].
With the current frequency in the center, the signal
strengths of 35 channels (+/-16 channels) bandwidth are
shown on a graph.
3 Rotate the DIAL to move ▼ to a signal.
The signal at the center of the displayed graph becomes the operating frequency.
4 Touch [STOP].
The band scope scanning stops.
Tip To resume band scope scanning, touch [SRCH].
5 Press the key.
Tips
Press and hold the key for over one second to enter Set mode, then select [DISPLAY][3
BAND SCOPE]. The number of band scope channels can be changed to 17 or 71.
The band scope channel interval is the same as the VFO frequency step.
When band scope is active, the numeric keypad does not function.
The audio of A/B common frequency band can be heard while scanning.
There are 2 ways for scanning (scoping) as follows.
FULL: Continuously scans (scopes).
1Time: Scans (scopes) only once. Changing the frequency with the DIAL resumes scanning.
* In analog mode, only FULL is selected.
* In digital mode, only 1Time is selected.
107
Convenient Functions
Taking Picture Using the Optional Camera-Mounted Speaker
Microphone
Snapshot Function
Pictures can be taken by connecting the optional camera-mounted speaker microphone
(MH-85A11U).
Captured image data can be saved onto a microSD memory card inserted in the
transceiver.
The saved data can be displayed on the screen and transmitted to other transceivers*
as well.
In addition, the most recently captured image data can be transmitted to other transceivers*
by pressing
(Send Image Button) on the camera-mounted speaker microphone.
* Refer to the Yaesu website or catalog for the transceiver models to which images can be
transferred.
Shutter Button
Press to take a picture.
Connector
Send Image Button
Sends the most recently
taken image data.
PTT Switch
Press to enable transmission,
and release to return to
receive mode.
Speaker
Outputs sound.
Lens
Aim this part toward the object to photograph.
Do not touch the lens with fingers or other objects.
Microphone
Speak into this part
with a normal voice.
Clip
Securely clip the
microphone to belt or
other objects.
Connect to the DATA
terminal of the transceiver.
Make sure to insert the
connector in the right
direction
when connecting the speaker microphone
to the transceiver.
Connecting it forcibly to the transceiver
may cause damage.
1 Press and hold for over one second to turn off the transceiver.
2 Connect the camera-mounted speaker microphone (MH-85A11U) to the transceiver.
Tip Connect the connector to the DATA terminal of the transceiver.
3 Press and hold for over one second to turn on the transceiver.
Caution
When receiving an AM radio broadcast signal with the camera microphone connected, noise may
occur, but this is not a malfunction.
4 Press .
Aim the lens toward the object, then press
.
Make sure to keep at least 50 cm distance between the lens and the object. If the
object is too close, the picture will be out of focus, resulting in a blurred picture.
108
Convenient Functions
Tips Press and hold the key for over one second to enter Set mode, then select [OPTION]
[1 USB CAMERA], you can set the picture size (resolution) and image quality (compression
rate).
Captured images are saved onto the microSD memory card inserted in the transceiver.
If your station and the remote station are both in digital mode, you can transfer the image data
most recently taken by pressing
.
Cautions
y Do not directly photograph objects with strong light, such as the sun or other bright objects. Doing so
can cause malfunction.
y If the lens or the microphone gets dirty, use a dry, soft cloth to wipe off the contaminants.
y Do not place the MH-85A11U near heat emitting equipment or where it is exposed to direct sunlight.
Doing so can cause fire or a malfunction.
y Be careful not to drop the MH-85A11U. Applying a strong shock may result in damages or failure.
The captured image appears on the LCD.
5 To save the image onto the microSD memory card, touch [SAVE].
Press the
key or touch [DEL] returns the display to the previous operating
screen without saving the image.
6 After saving the image, to transmit the image to other transceivers, touch [SEND].
7 Touch [OK] to return the display to the previous operating screen.
Viewing the Saved Image
1
Touch [F MW] on the normal operation screen.
2 Touch [LOG].
3 Touch [PICT].
Displays the saved image data list.
4 Touch the image you want to display.
Displays the selected image.
5 Press the key 3 times to return to the previous operating screen.
Transmitting the Saved Image to Other Transceivers
1
Touch [F MW] on the normal operation screen.
2 Touch [LOG].
3 Touch [PICT].
Displays the saved image data list.
4 Touch the image you want to transmit.
Displays the selected image.
5 Touch [SEND] or [FWD].
Starts transmission. When transmission completes, the screen returns to the screen
in step 3.
6 Press the key twice to return to the previous operating screen.
Taking Picture Using the Optional Camera-Mounted Speaker Microphone Snapshot Function
109
Communicating with a Specific Remote Station
Communicating with a Specific Remote Station
Using the Tone Squelch Function
The tone squelch opens the speaker audio only when a signal containing the specified
CTCSS tone is received. Using the digital code squelch (DCS) opens the speaker audio
only when a signal containing the specified DCS code is received. When the tone squelch
function is active, signals from other stations not containing the specified code are not
heard. The receiver will be quiet while waiting for a call from a specific station over a long
period of time.
Cautions
y The tone squelch function does not function in digital mode. Touch [MODE] to switch the
communication mode to AMS (Automatic Mode Select Function) or analog mode in advance.
y The tone squelch function does not function when the APRS baud rate is set on B-band. In Set mode,
select [APRS][4 APRS MODEM], then switch the setting to OFF in advance.
Selecting the Squelch Type
1
Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [11 SQL TYPE].
4 Rotate the DIAL to select the desired squelch type.
5 Press .
The selected squelch type is set and the transceiver exits from Set mode.
110
Communicating with a Specific Remote Station
Using the Tone Squelch Function
Tips
The squelch type can be set for each frequency band on both A-band (Main) and B-band (Sub).
The CTCSS and DCS squelch settings are also active during scanning. If scanning is performed with
the CTCSS and DCS squelch function activated, scanning stops only when a signal containing the
specified CTCSS tone or DCS code is received.
Pressing the Monitor switch allows signals that do not contain a tone or DCS code, and signals with
different tones or DCS codes to all be heard.
Pressing and holding the
key for over one second to change the Set mode option allows you
to use this function more conveniently.
[SIGNALING][3 DCS INVERSION]: Allows you to receiving the DCS code of the inverted phase.
[SIGNALING] [10 SQL EXPANSION]: Allows specifying squelch types for transmit and receive
respectively.
Display Operation
OFF Deactivates transmit/ receive tone squelch function, etc.
TONE Activates CTCSS transmit tones ([TN] appears).
TONE SQL Activates the tone squelch receive function ([TSQ] appears).
DCS Activates the digital code squelch ([DCS] appears).
REV TONE
Activates the reverse tone ([RTN] appears).
Use to monitor communications based on the squelch control system in which
a tone signal is contained when communication is not performed and the tone
signal disappears when communication starts.
PR FREQ
Activates the no-communication squelch function for radios ([PR] appears).
You can specify no-communication signal tone frequencies within the range from
300 Hz to 3000 Hz in steps of 100 Hz.
PAGER (
see page
116)
Activates a new pager function ([PAG] appears).
When communicating via transceivers with your friends, specify personal codes
(each code is composed of two tones) so that you can call only specific stations.
D CD* Sends a DCS code only for transmission ([DC] appears).
TONE-DCS*
Sends a tone signal when transmitting, and waits for a DCS code when receiving
([T-D] appears).
D CD-TONE SQL*
Sends a DCS code when transmitting, and waits for a tone signal when receiving
([D-T] appears).
*: Press and hold the
key for over one second, then set [SIGNALING][10 SQL EXPANSION] to
ON. The setting options for D CD, TONE-DCS and D CD TONE SQL are added to the [SIGNALING] [11
SQL TYPE] in Set mode. This allows specifying the squelch types for transmit and receive respectively.
Setting the Tone Frequency
The tone frequency can be selected from 50 frequencies (from 67.0 Hz to 254.1 Hz).
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Rotate the dial, then touch [12 TONE SQL FREQ].
111
Communicating with a Specific Remote Station
Using the Tone Squelch Function
4 Rotate the dial to select the desired tone frequency.
5 Gently press the key 3 times.
The selected tone frequency is set and the transceiver exits from Set mode.
Tips
The tone frequency set by following the procedure above is also effective when tones are only
transmitted.
The default setting is 100 Hz.
Searching for the CTCSS Tone transmitted by the Remote Station
Search and display the tone squelch CTCSS tone transmitted by the remote station.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Rotate the DIAL, then touch [11 SQL TYPE].
4 Rotate the DIAL to select [TONE SQL].
5 Press the key.
6 Rotate the DIAL, then touch [12 TONE SQL FREQ].
7 Receive the signal from the remote station.
8 Touch [SRCH].
The transceiver begins searching for a matching tone frequency
When a corresponding tone frequency is detected, a beep sound is emitted and
searching stops temporarily. The detected tone frequency blinks.
Tip To set CTCSS to the detected tone frequency,
Touch [STOP]. → Hear the beep sound. → Gently press the
key 3 times.
The transceiver exits from Set mode.
Tip
To set the transceiver operation when scanning stops, see “Setting the Receive Operation When
Scanning Stops” on page 74.
112
Communicating with a Specific Remote Station
Using the Tone Squelch Function
Setting the DCS Code
The DCS code can be selected from 104 types (from 023 to 754).
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [2 DCS CODE].
4 Rotate the DIAL to select the desired DCS code.
5 Gently press the key 3 times.
The DCS code is set and the transceiver exits from Set mode.
Tip
The default setting is [023].
Searching for the DCS Code Used by the Remote Station
Search and display the DCS code used by the remote station.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [2 DCS CODE].
113
Communicating with a Specific Remote Station
Using the Tone Squelch Function
4 Touch [SRCH].
[DCS SEARCH] appears on the LCD.
The transceiver starts to search for the DCS code.
When a corresponding DCS code is detected, a beep is
emitted and searching stops temporarily. The detected
DCS code blinks.
Tip To stop searching, touch [STOP].
Tip To set the searched DCS code,
Touch [STOP]. → Hear the beep sound. → Gently press the
key 3 times.
The transceiver exits from Set mode.
Tip
For setting how the transceiver operates when scanning stops, see “Setting the Receive Operation
When Scanning Stops” on page 74.
Notification of a Call from a Remote Station by Vibration
Set the vibrator to alert you of a call from a remote station containing a corresponding
tone or DCS code.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [CONFIG].
3 Touch [22 VIBRATOR].
4 Rotate the DIAL to select [MODE], then press the key.
5 Rotate the DIAL to select [SIGNALING].
6 Press .
The vibrator setting is set and the transceiver exits from the Set mode.
Tip To deactivate the vibrator function, select [OFF] in step 5.
114
Communicating with a Specific Remote Station
Using the Tone Squelch Function
Tips
The vibrator can function for all frequency bands belonging to A-band (Main) and B-band (Sub).
If you select [BUSY] in step 5, when the transceiver receives a signal, BUSY LED and the vibration
function turn on simultaneously regardless of the communication mode or squelch type.
The vibrator functions when the vibrator setting is other than OFF. Press
to perform transmission,
and release
to deactivate the vibrator for 5 seconds.
Selecting the Vibrator Operation Mode
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [CONFIG].
3 Touch [22 VIBRATOR], then press the key.
4 Rotate the DIAL to select [SELECT], then press the key.
5 Rotate the DIAL to select the desired vibrator operation.
Remark The default setting: PATTERN1
PATTERN1 The vibrator functions continuously.
PATTERN2 The vibrator functions at long intervals.
PATTERN3 The vibrator functions at short intervals.
6 Press .
The selected vibrator operation is set and the transceiver exits from Set mode.
Notification of a Call from a Remote Station by the
Bell Function
Set the Bell sound to alert you of a call from a remote station containing a corresponding
tone or DCS code.
on the LCD blinks at the same time.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [1 BELL].
115
Communicating with a Specific Remote Station
Using the Tone Squelch Function
4 Rotate the DIAL to select [SELECT], then press the
key.
5 Rotate the DIAL to select [BELL].
6 Press .
The Bell function is activated to on and the transceiver exits from Set mode.
When the tone squelch or DCS code is set,
appears.
Tip To deactivate the Bell function, select [OFF] in step 5.
Tips
To use the Bell function, set the tone squelch or DCS to on.
The bell function cannot be used via the repeater.
When the bell function is on,
appears on the LCD.
When a signal is received from a remote station,
blinks.
When a signal is received from a remote station,
blinks.
When pressing to perform transmission, stops blinking
and lights up.
Changing the Number of Times the Bell Rings
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Touch [1 BELL].
4 Rotate the DIAL to select [RINGER], then press the key.
5 Rotate the DIAL to select the desired number of times the Bell rings.
Remark The default setting: Once
Tip You can select the number of times the bell rings from among 1 to 20 times, or continuous.
6 Press .
The setting is applied and the transceiver exits from Set mode.
116
Communicating with a Specific Remote Station
Calling Only a Specific Station New Pager Function
When using the transceivers with your friends, specifying personal codes (each code
composed of two CTCSS tones) allows you to call just a specific station. Even when
the person who is called is not near his or her transceiver, the information on the LCD
indicates that a call was received.
Caution
The new pager function does not function in digital mode. Touch [MODE] to switch the communication
mode to AMS (Automatic Mode Select Function) or analog mode in advance.
A
C
B
Mr. C sends the personal
code of Mr. B.
Three individuals A, B, and C,
each using a transceiver.
Only Mr. B is called.
I’m gonna
call Mr. B
Ring!
Ring,
Ring,
Flow of Operation to Use the Pager Function
Set the same code as that of the remote station.
Determine a frequency.
Transmit/receive.
Confirm reception via the information on the LCD and the bell sound.
Setting the Code for Your Station
Set the personal code (your code) to be called by other stations.
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
117
Communicating with a Specific Remote Station
Calling Only a Specific Station New Pager Function
3 Touch [6 PAGER].
4 Rotate the DIAL to select [CODE-RX], then press the key.
5 Rotate the DIAL to select the first element of the code from 1 to 50, then press the
key.
The cursor moves.
6 Rotate the DIAL to select the second element of the code from 1 to 50, then press the
key.
Caution The same code cannot be use for both elements.
7 Press .
Your station code is set and the transceiver exits from Set mode.
Tips The default setting: [05 47]
Even if the first and second parts of your personal code are reversed, i.e., [47 05] from [05 47]
they are still recognized as the same code.
If the same code is specified for all individuals, all the individuals can be called at the same
time.
Activating the New Pager Function
1
Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Rotate the DIAL, then touch [11 SQL TYPE].
4 Rotate the DIAL to select [PAGER].
5 Press .
The new pager function is activated and the transceiver exits from Set mode.
You are ready to make a call, or wait for a call from a remote station, using the new
pager function.
Calling a Specific Station
1
See “Activating the New Pager Function” on page 117to activate the new pager
function.
2 Press and hold the key for over one second.
The transceiver enters Set mode.
118
Communicating with a Specific Remote Station
Calling Only a Specific Station New Pager Function
3 Touch [SIGNALING].
4 Touch [6 New Pager Function].
5 Rotate the DIAL to select [CODE-TX], then press the key.
6 Rotate the DIAL to select the first element of the code used by the remote station, then
press the
key.
Caution Register the pager code of the remote station in advance.
The cursor moves.
7 Rotate the DIAL to select the second element of the code used by the remote station,
then press the
key.
8 Press .
The code is set and the transceiver exits from Set mode.
9 Press .
The remote station is called.
Being Called by the Remote Station (Standby Operation)
If you turn on the Bell Function ( see page 114), you are alerted to a call from the
remote station by the [PAG] display, the blinking [
] icon, and the Bell sound. Also, if you
turn on the vibrator function (
see page 113), the vibrator can alert you that you have
been called by the remote station.
Blinks
When called
Tip
Pressing and holding the key for over one second, and then selecting [SIGNALING] [6
New Pager Function] [ANS-BACK] [ON] in Set mode, automatically places the transceiver in
transmission mode (for about 2.5 seconds) when called by the remote party, and notifies the remote
party that you are ready to communicate.
119
Customize Menu Settings for Individual Use (Set Mode)
Customize Menu Settings for Individual Use (Set Mode)
Using Set Mode
Set Mode allows selecting various functions from the list and setting each function
according individual preferences.
Set Mode Operation
1
Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch the desired item in SETUP MENU.
3 Rotate the DIAL, then touch the desired Set mode
sub-menu.
4 Rotate the DIAL to select the desired item to set.
120
Customize Menu Settings for Individual Use (Set Mode)
Using Set Mode
[When there is no deeper level of menu items]
Go to step 7.
[When there is deeper level of menu items]
5
Press the key.
6 Rotate the DIAL to select the desired item to set.
7 Press .
Exits from Set mode.
Caution
On some setting screens, pressing does not exit from Set mode. In this case, press the key
several times to return to the frequency display screen.
Resetting the All Set Mode Settings
All the Set mode settings can be restored to the default settings by following the procedure
below.
1 Press and hold for over one second to turn off the transceiver.
2 While pressing the and keys simultaneously, press for over one second.
The transceiver turns ON. When you hear a beep sound, release the keys.
3 After “SET MODE RESET?” appears, touch [OK].
A beep sounds.
Tips To cancel resetting, touch [CANCEL].
To reset the following items, make sure to perform All Reset (
see page 51).
[TX/RX]
1-1 ANTENNA ATT
1-2 HALF DEVIATION
1-3 RX MODE
2-1 SQL TYPE
[MEMORY]
2 BANK NAME
3 MEMORY NAME
5 MEMORY SKIP
[SIGNALING]
2 DCS CODE
3 DCS INVERSION
6 PAGER
7 PR FREQUENCY
9 SQL S-METER
11 SQL TYPE
12 TONE SQL FREQ
[WIRES-X]
1 RPT/WIRES FREQ
2 SEARCH SETUP
4 EDIT CATEGORY TAG
[CONFIG]
5 CLOCK TYPE
12 PASSWORD
15 RPT SHIFT
16 RPT SHIFT FREQ
18 STEP
[APRS]
7 APRS MSG TXT
15 BEACON STATS TXT
18 DIGI PATH
19 GPS SETUP
23 CALLSIGN (APRS)
24 MY POSITION
25 MY SYMBOL (4:User)
[CALLSIGN]
1 CALLSIGN (DIGITAL)
121
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
DISPLAY
1 TARGET LOCATION Set what to display using the smart
navigation function.
COMPASS / NUMERIC 128
2 COMPASS Set the compass display of the smart
navigation function.
HEADING UP / NORTH UP 128
3 BAND SCOPE Set the number of search channels
for the band scope function.
17ch / 35ch / 71ch 128
4 LAMP Set the duration time of the backlight
and keys to be lit.
KEY: OFF / 2 to 10 SEC (KEY) /
CONTINUOUS KEY 5Sec
SAVE: ON / OFF
129
5 LANGUAGE Switch between Japanese/English
for the menus and Set mode, etc.
ENGLISH / JAPANESE 129
6 LCD CONTRAST Set the LCD contrast level. LEVEL 1 to LEVEL 15 LEVEL 7 129
7 LCD DIMMER Set the brightness level of the LCD
backlight and numeric keypad light.
LEVEL 1 to LEVEL 6
LEVEL 6
130
8 OPENING
MESSAGE
Set the opening message type. CALLSIGN / NORMAL / OFF /
DC / MESSAGE
130
9 SENSOR INFO Display the voltage. Voltage 130
10 S-METER SYMBOL Select the symbol used for the S/
PO meter.
4 types 131
11 SOFTWARE
VERSION
Display the software version. Main / Sub / DSP 131
TX / RX
1 MODE
1-1 ANTENNA ATT Switch the attenuator between ON/
OFF.
ON / OFF 50
1-2 HALF DEVIATION Set the transmission modulation
level.
ON / OFF 132
1-3 RX MODE Select the receive mode. AUTO / FM / AM 48
2 DIGITAL
2-1 SQL TYPE Set the squelch type for digital mode. SQL TYPE: OFF / CODE /
BREAK
SQL CODE: 001 to 126
133
2-2 DIGI POPUP Set the POP UP time. OFF / BND2s / BND4s / BND6s /
BND8s / BND10s / BND20s /
BND30s / BND60s / BNDCNT
133
2-3 LOCATION
SERVICE
Set whether or not to display your
current location in digital mode.
ON / OFF
For details on the function, see the GM
Function Instruction Manual.
2-4 STANDBY BEEP Switch the standby beep function
between ON/OFF.
ON / OFF 134
3 AUDIO
3-1 MIC GAIN Adjust the microphone gain level. LEVEL 1 to LEVEL 9 LEVEL 5 134
3-2 MUTE Set the muting level on the non-
operating band side when a signal is
received on the operating band side.
OFF / MUTE 30% / MUTE 50% /
MUTE 100%
44
3-3 RX AF DUAL Set the resumption time of radio
reception in the AF Dual mode.
Transmit and receive 1 second to
10 seconds, Fixed,
or transmission 1 second to 10
seconds.
Transmission 2 seconds
101
122
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
MEMORY
1 BANK LINK Set the memory bank link. BANK 1 to BANK 24, BANK LINK
ON / OFF
136
2 BANK NAME Assign a name to each memory
bank.
BANK 1 to BANK 24 64
3 MEMORY NAME Input the memory channel tag. Up to 16 letters 59
4 MEMORY PROTECT Set whether to allow or prohibit
memory channel registration.
ON / OFF 137
5 MEMORY SKIP Set for skip memory / specify
memory
OFF / SKIP / SELECT 77
6 MEMORY WRITE Set the automatic channel number
increment when registering to a
memory channel.
NEXT / LOWER 137
SIGNALING
1 BELL Set the bell function settings. SELECT: OFF / BELL
RINGER: 1 time to 20 times /
Continuous
114
2 DCS CODE Set the DCS code. 023 to 754 112
3 DCS INVERSION Select a combination of DCS
inversion codes in terms of
communication direction.
RX (Receive): NORMAL
(Homeomorphic) / INVERT
(Inversion) / BOTH (Both Phase)
TX (Transmission): NORMAL
(Homeomorphic) / INVERT
(Inversion)
138
4 DTMF MODE Set the transmission of DTMF code
registered to a DTMF memory
channel, DTMF code transmission
delay time, and DTMF code
transmission speed.
MODE: MANUAL / AUTO
DELAY: 50ms / 250ms / 450ms /
750ms / 1000ms
SPEED: 50ms / 100ms
104
5 DTMF MEMORY Set the DTMF auto dialer channel
and code (16 characters).
CH1 to CH10 103
6 PAGER Turn the pager answerback Function
ON/OFF, and specify a personal
code (transmit/receive).
ANS-BACK: ON / OFF
CODE-RX: 01 to 50 for each, 05 47
CODE-TX: 01 to 50 for each, 05 47
116
7 PR FREQUENCY Set a non-communication squelch. 300Hz to 3000Hz 1600Hz 139
8 SQL LEVEL Select a squelch level. Level 0 to Level 15 Level 1 139
9 SQL S-METER Select an S-Meter squelch level OFF / LEVEL 1 to LEVEL 9 140
10 SQL EXPANSION Set a squelch type separately for
Receive and transmit.
ON / OFF 140
11 SQL TYPE Select a squelch type. OFF / TONE / TONE SQL / DCS /
REV TONE / PR FREQ / PAGER
/ (D CD) / (TONE-DCS) / (DCD-
TONE SQL)
* The options in the parentheses
are available when the SQL
expansion is ON.
109
12 TONE SQL FREQ Set a tone frequency. 67.0Hz to 254.1Hz 100Hz 110
13 TONE-SRCH Set the audio output during tone
search. Turn the muting function on/
off and select a tone search speed.
MUTE: ON / OFF
SPEED: FAST / SLOW
141
14 WX ALERT Enables/Disables the Weather Alert
Feature
ON / OFF 141
123
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
SCAN
1 DW TIME Set the priority memory channel
monitoring interval.
0.1 SEC to 10 SEC 5.0 SEC 142
2 SCAN LAMP Set whether or not to light up the
scan lamp when scanning stops.
ON / OFF 142
3 SCAN RE-START Set the scanning restart time. 0.1 SEC to 10 SEC 2.0 SEC 142
4 SCAN RESUME Configure the scan stop mode
settings.
SCAN: BUSY / HOLD / 2sec to
10sec 5.0sec
DW: BUSY / HOLD / 2sec to
10sec
74
5 SCAN WIDTH Set the scan mode operation VFO: ALL / BAND
MEMORY: ALL CH / BAND
143
GM
1 DELETE GROUP Delete a registered group.
2 DELETE MEMBER Delete a registered member.
3 RADIO ID Display the transceiver specific
number (ID).
(Uneditable)
* For details of the functions, refer to the GM Function Instruction Manual.
WIRES-X
1 RPT/WIRES FREQ Set the frequency to be used for
Repeater/WIRES.
MANUAL / PRESET
2 SEARCH SETUP Set the WIRES ROOM selection
method.
HISTORY / ACTIVITY
3 EDIT CATEGORY
TAG
Edit category tags. C1 to C5
4 REMOVE ROOM/
NODE
Delete registered Category ROOMs. C1 to C5
* For details of the functions, refer to the WIRES-X Instruction Manual.
CONFIG
1 APO Set the length of time until the
transceiver turns off automatically.
OFF / 0.5 HOUR to 12 HOURS 145
2 BCLO Turn on/off the busy channel lockout
function.
ON / OFF 145
3 BEEP Set the beep emitting function, and
set whether or not to emit the beep
sound when a band edge/CH1 is
encountered.
SELECT: KEY&SCAN / KEY /
OFF
EDGE: OFF / ON
146
4 BUSY LED Turn on/off the BUSY indicator. A BAND: ON / OFF
B BAND: ON / OFF
RADIO: ON / OFF
146
5 CLOCK TYPE Set the clock shift function. A / B 147
6 GPS LOG Set the GPS log recording time
interval.
OFF / 1 SEC / 2 SEC / 5 SEC /
10 SEC / 30 SEC / 60 SEC
147
7 HOME VFO Enable/disable VFO transmission in
Home Channel.
ENABLE / DISABLE 147
8 LED LIGHT Set whether or not to turn on the light
when the
key is pressed.
147
9 LOCK Configure the lock mode setting. KEY&DIAL / PTT / KEY&PTT /
DIAL&PTT / ALL / KEY / DIAL
148
10 MONI/T-CALL
Select the function of the
switch.
MONI / T-CALL 148
124
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
11 TIMER Switch the timer between ON and
OFF.
ON: 00:00 to 23:59 /
OFF: 00:00 to 23:59 /
149
12 PASSWORD Input the password. OFF / [****] 149
13 PTT DELAY Set the PTT delay time. OFF / 20ms / 50ms / 100ms /
200ms
150
14 RPT ARS Turn the ARS function on/off. ON / OFF 150
15 RPT SHIFT Set the repeater shift direction. SIMPLEX / -RPT / +RPT 150
16 RPT SHIFT FREQ Set the repeater shift width. 0.000MHz to 150.000MHz 151
17 SAVE RX Set the receive save time. OFF / 0.2 SEC (1:1) to 60.0 SEC
(1:300)
151
18 STEP Set the channel step. AUTO / 5.0KHz / 62.5KHz /
8.33KHz / 9.0KHz / 10.0KHz /
12.5KHz / 15.0KHz / 20.0KHz /
25.0KHz / 50.0KHz / 100KHz
47
19 DATE & TIME ADJ Set the built-in clock. 43
20 TOT Set the timeout timer. OFF / 30 SEC to 10 MIN
(European version: 3 MIN)
152
21 VFO MODE Select the frequency selection range
in the VFO mode.
ALL / BAND 152
22 VIBRATOR Select a vibrator mode and set up
the vibrator function.
MODE: OFF / BUSY /
SIGNALING
SELECT: PATTERN1 /
PATTERN2 / PATTERN3
113
23 DIAL KNOB
CHANGE
Swap the DIAL and VOL knob
functions.
152
APRS
1 APRS AF DUAL Turn on/off the muting function when
both the APRS function and AF dual
function are active.
ON / OFF
2 APRS DESTINATION Display the model code. APY02D (Uneditable)
3 APRS FILTER Select the filter function. Mic-E: ON / OFF
POSITION: ON / OFF
WEATHER: ON / OFF
OBJECT: ON / OFF
ITEM: ON / OFF
STATUS: ON / OFF
OTHER: ON / OFF
ALTNET: ON / OFF
4
APRS
MODEM Set the APRS baud rate. OFF / 1200bps / 9600bps
5 APRS MSG FLASH Set the strobe to flash when there is
an incoming message.
MSG: OFF / 2s to 60s /
CONTINUOUS / EVERY 2s to
EVERY 10s 4sec
GRP: OFF / 2s to 60s /
CONTINUOUS 4sec
BLN: OFF / 2s to 60s /
CONTINUOUS 4sec
125
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
6 APRS MSG GROUP Group filtering for received
messages.
G1: ALLxxxxxx
G2: CQxxxxxx
G3: QSTxxxxxx
G4: YAESUxxxxxx
G5: ----------
B1: BLNxxxxxx
B2: BLNx
B3: BLNx
7 APRS MSG TXT Input the fixed text message. 1 to 8 ch
8 APRS MUTE Set the B-band AF muting function
on/off when APRS is active.
ON / OFF
9 APRS POPUP Set the beacon type, message type
and time for pop-up display.
The setting values of Mic-E,
POSITION, WEATHER,
OBJECT, ITEM, STATUS,
OTHER, MY PACKET, MSG,
GRP and BLN are as follows.
OFF / ALL2s to ALL60s /
ALLCNT / BND2s to BND60s /
BNDCNT ALL10s
The setting values of MY MSG,
DUP.BCN, DUP.MSG. ACK.REJ
and OTHER MSG are as follows.
OFF / BND2s to BND60s
BND10s
10 APRS RINGER Set the bell ring on/off when a
beacon or message is received.
Mic-E: ON / OFF
POSITION: ON / OFF
WEATHER: ON / OFF
OBJECT: ON / OFF
ITEM: ON / OFF
STATUS: ON / OFF
OTHER: ON / OFF
MY PACKET: ON / OFF
MSG: ON / OFF
GRP: ON / OFF
BLN: ON / OFF
MY MSG: ON / OFF
DUP.BCN: ON / OFF
DUP.MSG: ON / OFF
ACK.REJ: ON / OFF
OTHER MSG: ON / OFF
TX BCN: ON / OFF
TX MSG: ON / OFF
11 APRS UNIT Select the units for APRS display. POSITION: MM.MM' / MM'SS"
DISTANCE: km / mile
SPEED: km/h / knot / mph
ALTITUDE: m / ft
TEMP: °C / °F
RAIN: mm / inch
WIND: m/s / mph
12 APRS TX DELAY Set the data sending delay time. 100ms / 150ms / 200ms / 250ms /
300ms / 400ms / 500ms /
750ms / 1000ms
126
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
13 BEACON INFO Set the transmission beacon
information.
AMBIGUITY: OFF / 1 digit /
2 digit / 3 digit / 4 digit
SPD / CSE: ON / OFF
ALTITUDE: ON / OFF
14 BEACON
INTERVAL
Set a beacon automatic sending
interval.
30sec / 1min / 2min / 3min / 5min
/ 10min / 15min / 20min / 30min
/ 60min
15 BEACON STATS
TXT
Input setting for status text. S.TXT: ON / OFF
TX RATE: 1/1 to 1/8
TEXT: TEXT1 to TEXT5
16 BEACON TX Select automatic or manual sending
of beacon.
AUTO / MANUAL
17 COM PORT
SETTING
Set the COM port. STATUS: ON / OFF
SPEED: 4800 / 9600 / 19200 /
38400
INPUT: OFF / GPS
OUTPUT: OFF / GPS / WAY.P /
DSP H / DSP A / DSP D
WAYPOINT: NMEA9 / NMEA6 /
NMEA7 / NMEA8
Mic-E: ON / OFF
POSIT: ON / OFF
WEATHER: ON / OFF
OBJECT: ON / OFF
ITEM: ON / OFF
18 DIGI PATH Set the digital repeater route. P1 OFF
P2(1) 1 WIDE1-1
P3(2) 1 WIDE2-1 / 2 WIDE2-1
P4(2) 1 / 2
P5(2) 1 / 2
P6(2) 1 / 2
P7(2) 1 / 2
P8(8) 1 to 8
19 GPS SETUP Select a datum used for the GPS
function.
DATLM: WGS-84 / Tokyo (Mean)
PINNING: ON / OFF
DGPS: ON / OFF
20 GPS POWER Turn the GPS function on/off. GPS ON / GPS OFF
21 GPS TIME SET Turn on/off the GPS time and date
automatic acquisition function.
AUTO / MANUAL
22 GPS UNIT Select the units for GPS display. POSITION: .MMM' / 'SS"
SPEED: km/h / knot / mph
ALTITUDE: m / ft
23 CALLSIGN (APRS) Specify the call sign of your station. – – – – – – – –
24 MY POSITION Set your location GPS / Manual / P1 to P10
25 MY SYMBOL Set your station symbol. 48 icons including 1(/[Human
person]) / 2(/b Bicycle) / 3(/>
Car) / 4(YY Yaesu Radios)
26 POSITION
COMMENT
Set up the position comment
function.
Off Duty / En Route / In Service
/ Returning / Committed / Special
/ Priority / Custom 0 to 6 /
EMERGENCY!
127
Customize Menu Settings for Individual Use (Set Mode)
Tables of Set Mode Operations
Set mode no. / item Description
Selectable options
(Options in bold are the default settings)
Page
27 SmartBeaconing Set the smart beaconing function. STATUS: OFF / TYPE1 / TYPE2 /
TYPE3
* For details on the following
setting items for each type, refer
to the APRS Instruction Manual.
LOW SPD, HIGH SPD,
SLOW RATE, FAST RATE,
TURN ANGL, TURN SLOP,
TURN TIME
28 TIME ZONE Set the time zone. UTC −13:00 to UTC 0:00 to UTC
+13:00 UTC 0:00
* For details of the functions, refer to the APRS Instruction Manual.
SD CARD
1 BACKUP Save the data stored on the
transceiver onto a microSD memory
card or load the data from a microSD
card.
Write to SD / Read from SD 154
2 MEMORY CH Save or load the memory channel
information onto or from a microSD
memory card.
Write to SD / Read from SD 155
3 GROUP ID Save or load the GROUP ID
information onto or from a microSD
memory card.
Write to SD / Read from SD 155
4 FORMAT Initialize microSD memory cards. 31
OPTION
1 USB CAMERA Set the USB camera image size,
resolution and Speaker.
SIZE: 160*120 / 320*240
QUALITY: LOW / NORMAL /
HIGH
SP SEL: CAMERA / INT SP
157
CALLSIGN
1 CALLSIGN Set the call sign. xxxxxxxxxx 158
128
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: DISPLAY Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[DISPLAY] to reveal specific items.
After completing the setup, press to exit from Set mode.
Setting What to Display Using the Smart Navigation Function
Set what to display on the smart navigation screen.
1 Touch [1 TARGET LOCATION].
2 Rotate the DIAL to select what is displayed on the screen.
COMPASS Displays the compass.
NUMERIC Displays the latitude and longitude.
Remark The default setting: COMPASS
Setting the Compass Display
Set the compass display.
1 Touch [2 COMPASS].
2 Rotate the DIAL to select the desired setting.
HEADING UP The heading direction is indicated at the top of the compass.
NORTH UP The north direction is indicated at the top of the compass.
Remark The default setting: HEADING UP
Setting the Search Channels for the BAND SCOPE Function
Set the number of channels to be displayed for the band scope when the BAND SCOPE
function is used.
1 Touch [3 BAND SCOPE].
2 Rotate the DIAL to select the number of channels to search for.
17ch / 35ch / 71ch
Remark The default setting: 35ch
129
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: DISPLAY Menu Operations
Changing the Lighting Condition
Change the LCD and key lighting condition.
1 Touch [4 LAMP].
2 Rotate the DIAL to select [KEY], then press the key.
3 Rotate the DIAL to select the lighting condition.
2 SEC (KEY) to
10 SEC (KEY)
When the DIAL is rotated or a key is pressed, the LCD and key
lights remain illuminated for the set time.
CONTINUOUS The LCD and key lights remain illuminated.
OFF The LCD and keys do not light up.
Remark The default setting: 5 SEC (KEY)
4 Press the key.
5 Rotate the DIAL to select [SAVE], then press the key.
6 Rotate the DIAL to select the lighting status after the set illumination time elapses.
OFF After the illumination time selected for [KEY] elapses, the lights
dim to [LEVEL 1] of the LCD dimmer setting.
ON After the illumination time selected for [KEY] elapses, lights turn
off.
Remark The default setting: OFF
Caution
When [KEY] is set to CONTINUOUS, regardless of the [SAVE] setting, the illumination stays lit
according to the LCD dimmer setting level.
Selecting the Display Language
Select the display language from Japanese and English.
1 Touch [5 LANGUAGE].
2 Rotate the DIAL to select the desired language.
JAPANESE Japanese is selected.
ENGLISH English is selected.
Remark The default setting: English
Adjusting the LCD Contrast Level
Adjust the LCD contrast level.
1 Touch [6 LCD CONTRAST].
2 Rotate the DIAL to select the desired contrast level.
Select from LEVEL 1 to LEVEL 15.
Remark The default setting: LEVEL 7
130
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: DISPLAY Menu Operations
Adjusting the LCD Backlight and Key Button Light Brightness Level
Adjust the brightness level of the LCD backlight and key button* light.
1 Rotate the DIAL, then touch [7 LCD DIMMER]
2 Rotate the DIAL to select the desired brightness level.
Select from LEVEL 1 to LEVEL 6.
Remark The default setting: LEVEL 6
*“Key button” refers to the keys / switches such as
and located below the LCD panel.
Changing the Opening Message Displayed Immediately after Power-
on
You can select the message under the “YAESU” logo displayed when turning on the
transceiver.
1 Rotate the DIAL, then touch [8 OPENING MESSAGE].
2 Rotate the DIAL to select the desired message referring to the following table.
OFF Displays the receive frequency instead of the opening message
immediately after turning on the power.
DC Displays the power-supply voltage and time when turning on the
power.
MESSAGE Displays a message comprising up to 16 characters when turning
on the power. Press the
key to switch the screen to the
message registration screen. See “Entering Letters” on page 19
to input the message you want to display.
CALLSIGN Displays your call sign when turning on the power.
Displaying the Battery Voltage
Display the battery voltage. When the optional external power supply adapter with
a cigarette plug (SDD-13) is connected, the power supply voltage of this adapter is
displayed.
1 Rotate the DIAL, then touch [9 SENSOR INFO].
The battery voltage is shown on the LCD.
Tips
The indication differs depending on the type of the power supply used.
Battery pack: “Lit”
Battery case: “Dry”
External power supply adapter: “Ext”
During mono band receive, the voltage can be displayed on the LCD constantly (
see page 34).
131
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: DISPLAY Menu Operations
Changing the Display Pattern of the S-Meter
Select the desired display pattern of the S-Meter.
1 Rotate the DIAL, then touch [10 S-METER SYMBOL].
2 Rotate the DIAL to select the desired display pattern.
1
2
3
4
Remark The default setting: 1
Displaying the Software Version
Display the software version.
1 Rotate the DIAL, then touch [11 SOFTWARE VERSION].
The software versions of “Main”, “Sub” and “DSP” are shown.
132
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: TX/RX Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[TX/RX] to display the sub-menu items. Set each item under the sub-menu.
After completing the setup, press to exit from Set mode.
Reducing Receiver Sensitivity
Attenuator (ATT) Function
If the signal from the remote station is too strong or, a strong signal exists nearby that
interferes with reception, use the attenuator (ATT) function to reduce interference by
selecting [1 MODE][1 ANTENNA ATT].
For details, see “Attenuator (ATT) Function (except AM broadcasts and AM broadcasts)”
on page 50.
Tip
The amount of attenuation by the attenuator (ATT) is about 10 dB.
Setting the Transmit Modulation Level
The transmit modulation level can be set to half of its usual level.
Select [OFF] for normal amateur operation.
1 Touch [1 MODE].
2 Touch [2 HALF DEVIATION].
3 Rotate the DIAL to select the desired setting.
OFF Normal transmission modulation level
ON The level is half of the normal transmit
modulation level.
Remark The default setting: OFF
133
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: TX/RX Menu Operations
Switching the Receive Mode
Manually switch to a suitable mode (radio wave type) according to the frequency band by
selecting [1 MODE][3 RX MODE].
For details, see “Changing the Mode” on page 48.
Setting the Squelch Type for the Digital Mode
Set the squelch type for the digital mode.
1 Touch [2 DIGITAL].
2 Touch [1 SQL TYPE].
3 Rotate the DIAL to select [SQL TYPE], then press the key.
4 Rotate the DIAL to select the desired squelch type.
OFF Audio is always output upon receiving a digital signal from a Yaesu
transceiver.
CODE Audio is output only when receiving a signal with a corresponding
SQL CODE.
BREAK Audio is output regardless of any squelch code when the remote
station transmits with BREAK set.
Remark The default setting: OFF
5 Press the key.
6 Rotate the DIAL to select [SQL CODE], then press the key.
7 Rotate the DIAL to select the desired code.
Set SQL CODE any one of 126 types (001 to 126).
Setting the Pop-up Time of the Remote Station Information
Set the time duration to display the remote station information such as the call sign, on
the LCD.
1 Touch [2 DIGITAL].
2 Touch [2 DIGI POPUP].
3 Rotate the DIAL to select the desired setting.
OFF The remote station information is not displayed.
BND2s to
60s
Set the time duration to display the remote station information (2 to
60 seconds).
BND2s / BND4s / BND6s / BND8s / BND10s / BND20s / BND30s /
BND60s
BNDCNT The remote station information is continuously displayed.
Remark The default setting: BAND 10 seconds
134
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: TX/RX Menu Operations
Displaying Your Location in Digital Mode
Set whether or not to display your location in digital mode.
1 Touch [2 DIGITAL].
2 Touch [3 LOCATION SERVICE].
3 Rotate the DIAL to select the desired setting.
ON Displays your location.
OFF Does not display your location.
Remark The default setting: ON
For details on the function, refer to the GM Function Instruction Manual.
Setting the Standby Beep
Set whether or not to emit the standby beep sound when the remote station completes
transmission.
1 Touch [2 DIGITAL].
2 Touch [4 STANDBY BEEP].
3 Rotate the DIAL to select the desired setting.
ON Emits the standby beep sound.
OFF Does not emit the standby beep sound.
Remark The default setting: ON
Adjusting the Microphone Sensitivity Microphone Gain
You can adjust the input level of the built-in microphone or an optional external microphone.
1 Touch [3 AUDIO].
2 Touch [1 MIC GAIN].
3 Rotate the DIAL to select the desired microphone sensitivity level.
Select a microphone gain level from LEVEL 1 to LEVEL 9.
Remark The default setting: LEVEL 5
Tips
Increasing the microphone gain excessively can distort the sound or pick up the surrounding noise,
impairing intelligibility.
Be sure to check the microphone gain whenever the microphone is changed.
135
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: TX/RX Menu Operations
Muting Audio
In the dual receive mode, the audio being received on the non-operating band can be
muted by selecting [3 AUDIO][2 MUTE].
For details, see “Muting Audio” on page 44.
Simultaneous Radio Broadcast Reception
Set the time to resume radio broadcast reception after transmit/receive when using
simultaneously receive mode, by selecting [3 AUDIO][3 RX AF DUAL].
For details, see “Setting the Resumption Time of Radio Reception” on page 101.
136
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: MEMORY Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[MEMORY] to set the individual items.
After completing the setup, press to exit from Set mode.
Setting Memory Bank Link
You can link multiple registered memory banks so that you can recall frequently used
memory banks immediately.
1 Touch [1 BANK LINK].
2 Rotate the DIAL to select the memory bank you want to link, then press the key.
The checkbox is checked.
3 Repeat step 2 to link the memory banks one by one from BANK 1 to BANK 24.
Assigning Name to Memory Bank
By selecting [2 BANK NAME], you can assign a name to each memory bank using up to
16 characters.
For details, see “Assigning Name to Memory Bank” on page 64.
Assigning Name to Memory Channel
By selecting [3 MEMORY NAME], you can assign a name such as a call sign and
broadcast station name to each memory channel and home channel.
For details, see “Using Memory Tag” on page 59.
137
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: MEMORY Menu Operations
Prohibiting Registration to a Memory Channel
Memory Channel Protect Function
A memory channel may be protected so that a new frequency or memory channel tag
name cannot be registered to it.
1 Touch [4 MEMORY PROTECT].
2 Rotate the DIAL to select the desired setting.
OFF Allows registering to registering to memory channels.
ON Prohibits registering to memory channels.
Remark The default setting: OFF
Setting Memory Skip Function
By selecting [5 MEMORY SKIP], you can set the scan method for scanning memory
channels.
For details, see “Specifying Skip/Selected Memory Channels” on page 77.
Setting the Memory Channels Used for Registration
Set whether to register to the lowest unused memory channel number following the channel
number you most recently used, or to the lowest unused memory channel number.
1 Touch [6 MEMORY WRITE].
2 Rotate the DIAL to select the desired setting.
NEXT Registers to the smallest unused memory channel number which
comes after the channel number you used most recently.
LOWER Registers to the unused memory channel having the lowest memory
number.
Remark The default setting: NEXT
138
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SIGNALING Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[SIGNALING] to set the individual items.
After completing the setup, press to exit from Set mode.
Notification of a Call from a Remote Station by the Bell
Set whether or not to alert you of a call from a remote station using the bell by selecting
[1 BELL].
For details, see “Notification of a Call from a Remote Station by the Bell Function” on
page 114.
Selecting a DCS Code
Select the DCS code out of the 104 codes from 023 to 754 by selecting [2 DCS CODE].
For more details, see “Setting the DCS Code” on page 112.
Transmitting and Receiving a DCS Code with an Inverted Phase
DCS INVERSION Function
The transmit and receive DCS code phase may be inverted when using the digital code
squelch function.
1 Touch [3 DCS INVERSION].
2 Rotate the DIAL to select the phase combination for transmit/receive.
RX Homeomorphic / Both Phase / Inverted
Phase
TX Homeomorphic / Inverted Phase
Remark The default setting: Receive [Homeomorphic], Transmit [Homeomorphic]
Setting the Transmission Method of the DTMF Code
Set the transmission method of the registered DTMF code by selecting [4 DTMF MODE].
For details, see “Transmitting the Registered DTMF Code” on page 104.
139
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SIGNALING Menu Operations
Setting the DTMF Code
By selecting [5 DTMF SELECT], the maximum of 16 digit DTMF code can be registered
for a telephone number to make a call through the public telephone line from a phone
patch.
For details, see “Using the DTMF Function” on page 103.
Calling Only a Specific Station (New Pager Function)
When using transceivers with a group of friends, specifying individual personal codes
permits directing a call to a specific station by selecting [6 PAGER].
For details, see “Calling Only a Specific Station New Pager Function” on page 116.
Enabling No-communication Squelch Function PR FREQUENCY
Function
Set a no-communication squelch frequency in steps of 100 Hz within the range from 300
Hz to 3000 Hz.
1 Touch [7 PR FREQUENCY].
2 Rotate the DIAL to tune in to a no-communication squelch frequency.
Select a no-communication squelch frequency in steps of 100 Hz within the range
from 300 Hz to 3000 Hz.
Remark The default setting: 1600 Hz
Adjusting the Squelch Level SQL LEVEL Function
Set the squelch level to mute the raspy noise heard when there is no signal.
1 Touch [8 SQL LEVEL].
2 Rotate the DIAL to adjust the squelch level from LEVEL 0 to LEVEL 15.
Remark The default setting: LEVEL1
140
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SIGNALING Menu Operations
Setting the Squelch to Activate at a Specified Signal Strength
S-Meter Squelch Function
You can set A-Band and B-Band individually to emit audio only when receiving a signal
stronger than the S-meter Squelch level setting.
To adjust the S-Meter squelch, first set the operating band by pressing the
key.
1 Touch [9 SQL S-METER].
2 Rotate the DIAL to select the setting value referring to the table below.
Remark The default setting: OFF
Display S-Meter Display Operating Status
OFF No display
S-Meter squelch function is OFF.
(By default, S-Meter squelch function is set to
OFF.)
LEVEL1
Outputs the audio of a signal as strong or
stronger than the S-Meter level 1.
LEVEL2
Outputs the audio of a signal as strong or
stronger than the S-Meter level 2.
LEVEL3
Outputs the audio of a signal as strong or
stronger than the S-Meter level 3.
LEVEL4
Outputs the audio of a signal as strong or
stronger than the S-Meter level 4.
LEVEL5
Outputs the audio of a signal as strong or
stronger than the S-Meter level 5.
LEVEL6
Outputs the audio of a signal as strong or
stronger than the S-Meter level 6.
LEVEL7
Outputs the audio of a signal as strong or
stronger than the S-Meter level 7.
LEVEL8
Outputs the audio of a signal as strong or
stronger than the S-Meter level 8.
LEVEL9
Outputs the audio of a signal as strong or
stronger than the S-Meter level 9.
Setting the Squelch Type for Transmit and Receive
SQL EXPANSION Function
You can add squelch types to [11 SQL TYPE] for transmit and receive, respectively.
1 Rotate the DIAL, then touch [10 SQL EXPANSION].
2 Rotate the DIAL to select the desired setting.
ON Add squelch types for transmit and receive, respectively.
OFF Does not add squelch types for transmit and receive, respectively.
Remark The default setting: OFF
141
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SIGNALING Menu Operations
Setting the Type of Squelch
Select [11 SQL TYPE] to open the squelch only when a signal containing the specified
tone or code is received.
For details, see “Using the Tone Squelch Function” on page 109.
Selecting a CTCSS Tone Frequency
Select [12 TONE SQL FREQ] to select the tone frequency from 50 types between 67.0
MHz and 254.1 MHz.
For details, see “Setting the Tone Frequency” on page 110.
Setting the Sound and Speed During Tone Search
Tone Search Function
The audio may be muted during tone search. The operation speed of the tone search can
also be changed.
1 Rotate the DIAL, then touch [13 TONE-SRCH].
2 Rotate the DIAL to select [MUTE], then press the key.
3 Rotate the DIAL to select the desired setting.
ON Mutes the audio during the tone search operation.
OFF Does not mute the audio during the tone search operation.
Remark The default setting: ON
4 Rotate the DIAL to select [SPEED], then press the key.
5 Rotate the DIAL to select the desired setting.
FAST Speed up the tone search operation.
SLOW Slow down the tone search operation.
Remark The default setting: FAST
ON/OFF for the Weather Alert Feature
Setting the weather Alert Feature, used for notifying storms and hurricanes, ON or OFF.
1 Rotate the DIAL, then touch [14 WX ALERT].
2 Rotate the DIAL to select the desired setting.
ON Enables the Weather Alert Feature.
OFF Disables the Weather Alert Feature.
Remark The default setting: OFF
142
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SCAN Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[SCAN] to set the individual items.
After completing the setup, press to exit from Set mode.
Setting the Surveillance Interval Time for Priority Channels
DW INTERVAL TIME Function
When the dual receive function is active, the interval time at which the priority channel is
monitored can be set.
1 Rotate the DIAL, then touch [1 DW TIME].
2 Rotate the DIAL to select the monitoring interval from 0.1 SEC to 10 SEC.
Remark The default setting: 5.0 seconds
Setting the Illumination On/Off When Scanning Stops
LAMP Function
Set whether or not the LCD backlight is turned on when a signal is received during
scanning.
1 Rotate the DIAL, then touch [2 SCAN LAMP].
2 Rotate the DIAL to select the desired setting.
ON The LCD backlight will illuminate when a signal is received.
OFF The LCD backlight will not illuminate when a signal is received.
Remark The default setting: ON
Setting the Time to Resume Scanning
SCAN RE-START Function
Set the time interval to resuming scanning after a received signal ends during scanning.
1 Rotate the DIAL, then touch [3 SCAN RE-START].
2 Rotate the DIAL to select the time to resume scanning from 0.1 SEC to 10 SEC.
Remark The default setting: 2.0 seconds
143
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SCAN Menu Operations
Selecting a Receive Operation When Scanning Stops
Touch [4 SCAN RESUME] to set the receive operation for when scanning stops.
For details, see “Setting the Receive Operation When Scanning Stops” on page 74.
Setting the Scanning Range
You can set the frequency range for scanning in VFO mode and Memory mode.
1 Touch [5 SCAN WIDTH].
2 Rotate the DIAL to select [VFO], then press the key.
3 Rotate the DIAL to select the desired setting referring to the table below.
ALL
Scans all bands from the current frequency within the 1.8 MHz to 999
MHz range.
BAND Starting with the current frequency, scans within the current band.
4 Press the key.
5 Rotate the DIAL to select [MEMORY], then press the key.
6 Rotate the DIAL to select the desired setting referring to the table below.
ALL CH
Scans all memory channels (1 to 900) starting with the currently specified
memory channel. When “Selected memory channel” is selected, all
specified memory channels are scanned (
see page 76).
BAND
Scans only the memory channels to which the frequencies are registered,
within the same frequency band
*1
as the currently specified memory
channel.
When the memory channels are registered as the specified memory
channels, scans only the specified memory channels to which the
frequencies are registered, within the same frequency band.
*1
*1: For the relationship between frequency bands and receive frequencies, see the table at the
bottom of page 36.
144
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: GM Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[GM] to set the individual items.
After completing the setup, press to exit from Set mode.
For details on how to set each item, refer to “FT2DR/DE GM Function Instruction Manual”
which is available on Yaesu website.
Set Mode: WIRES-X Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[WIRES] to set the individual items.
After completing the setup, press to exit from Set mode.
For details on how to set each item, refer to “FT2DR/DE WIRES-X Instruction Manual”
which is available on Yaesu website.
145
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[CONFIG] to set the individual items.
After completing the setup, press to exit from Set mode.
Turn Power Off Automatically Auto Power-Off Function
Set whether or not to turn off the transceiver automatically if there is no operation for a
certain period of time.
1 Touch [1 APO].
2 Rotate the DIAL to select the desired setting.
OFF Does not turn off the power automatically.
30 minutes to
12 hours
Turns off the power when no operation is performed for a specified
period of time.
Remark The default setting: OFF
Tips
When the auto power-off function is active, appears on the LCD.
Once the time for automatic power-off is set, the new setting is retained. Unless “OFF” is selected in
step 2, the next time the transceiver is turned on, if you perform no operation for the set period of time,
the transceiver will automatically turn off.)
Preventing Accidental Transmission
Busy Channel Lockout (BCLO) Function
Preventing transmissions when the receive channel is busy.
1 Touch [2 BCLO].
2 Rotate the DIAL to select the desired setting.
OFF Permits starting a transmission while receiving a signal.
ON Disables transmissions while receiving a signal.
Remark The default setting: OFF
146
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Setting the Key Operation Confirmation Sound
Set whether or not a beep sound is emitted to confirm when keys are operated, when
scanning reaches the end of a frequency band, or when a band edge/CH1 is encountered.
1 Touch [3 BEEP].
2 Rotate the DIAL to select [SELECT], then press the key.
3 Rotate the DIAL to select the desired setting referring to the table below.
KEY &
SCAN
Emits the beep sound when a key is operated or scanning stops.
KEY Emits the beep sound when a key is pressed.
OFF Mutes the beep sound.
Remark The default setting: KEY & SCAN
4 Press the .
5 Rotate the DIAL to select [EDGE], then press the key.
6 Rotate the DIAL to select the desired setting referring to the table below.
OFF No confirmation sound is emitted when a band edge/CH1 is encountered.
ON Emits the confirmation sound when a band edge/CH1 is encountered.
Remark The default setting: OFF
Turning off the BUSY Indicator
When listening to the radio continuously or to extend the remaining battery operating
time, turn off the BUSY indicator to save battery power consumption.
1 Touch [4 BUSY LED].
2 Rotate the DIAL to select “A BAND”, “B BAND” or “RADIO”, then press the key.
3 Rotate the DIAL to select the desired setting.
ON Turns on the BUSY indicator.
OFF Turns off the BUSY indicator.
Remark The default setting: ON
4 Press the key.
5 To change the setting for other bands, repeat steps 2 to 4.
147
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Setting the Clock Shift for the Micro Computer
Clock Type Function
Set the micro computer Clock Shift function may be activated to eliminate an internally
generated spurious high frequency signal. Select [A] for normal use.
1 Touch [5 CLOCK TYPE].
2 Rotate the DIAL to select the desired setting.
A Automatically switches the Clock Shift function between on/off.
B Activates the Clock Shift function constantly.
Remark The default setting: A
Setting a Time Interval for Saving GPS Position Information
Set the interval at which the current position GPS information is saved to the microSD
memory card.
1 Touch [6 GPS LOG].
2 Rotate the DIAL to select the time interval:
OFF / 1 SEC / 2 SEC / 5 SEC /10 SEC / 30 SEC / 60 SEC
If OFF is selected, no GPS Information is saved onto the microSD memory card
Remark The default setting: OFF
Tips
Data saved onto the microSD memory card is saved in GPSyymmddhhmmss.LOG format.
Saved data may be viewed by using OEM PC applications*.
* Yaesu does not provide technical support for PC applications.
Permitting/Prohibiting Transfer of Home Channel Frequency to VFO
Set whether or not to permit tuning off of the home channel and transfer to the VFO.
1 Touch [7 HOME VFO].
2 Rotate the DIAL to select the desired setting.
ENABLE Turning the DIAL in home channel transfers from the home channel
frequency to the VFO.
DISABLE Turning the Dial on the home channel does not switch to the VFO.
Remark The default setting: ENABLE
Using the LED Light
148
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Pressing the key turns the LED light on/off.
1 Touch [8 LED LIGHT].
The LED light turns on.
2 Press the key.
The LED light turns off.
Setting the LOCK Function
Select keys/DIAL to which you want to apply the lock function.
1 Touch [9 LOCK].
2 Rotate the DIAL to select the desired setting.
KEY & DIAL Locks the DIAL and keys on the front side of the transceiver.
PTT Locks .
KEY & PTT Locks and the keys on the front side of the transceiver.
DIAL & PTT Locks the DIAL and .
ALL Locks the DIAL, and the keys on the front side of the transceiver.
KEY Locks the keys on the front side of the transceiver.
DIAL Locks the DIAL.
Remark The default setting: KEY & DIAL
Setting the Operation of the Key
Set how the transceiver functions when the key is pressed.
1 Touch [10 MONI/T-CALL].
2 Rotate the DIAL to select the desired setting.
MONI Monitors frequencies.
T-CALL Functions as the tone call.
Remark The default setting: MONI
149
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Turning on/off the Transceiver at the Specified Time
Timer Function
You can turn the transceiver to on or off at the specified time. Before using this function,
adjust the clock referring to “Setting Clock Time” on page 43.
1 Rotate the DIAL, then touch [11 TIMER].
2 Rotate the DIAL to select the desired option.
POWER ON Turns on the transceiver at the specified time.
POWER OFF Turns off the transceiver at the specified time.
3 Press the key.
4 Rotate the DIAL to set the hour, then press the key.
5 Rotate the DIAL to set the minute, then press the key.
6 Touch [TIMER ON] or [TIMER OFF] to set the timer function to on or off.
Touch [TIMER OFF] to deactivate the timer function.
Remark The default setting: (TIMER OFF)
Password Function
You can enter a 4-digit password to prevent a third party from using your transceiver
without permission. Once a password is set, the transceiver cannot be used unless the
valid password is entered.
1 Rotate the DIAL, then touch [12 PASSWORD].
2 Rotate the DIAL to select [ON].
ON Set the password.
OFF Does not set the password.
Remark The default setting: OFF
3 Press the key.
4 Use the numeric keypad to input your desired 4 letters using 0 to 9, A to D, * or #.
5 Press the key.
The registered 4 letters appear.
Tips
To deactivate the password function, select [OFF] in step 2, then press .
When the on-timer function is activated, the password function is disabled.
y Inputting the Password to Use the Transceiver
1 Press for over one second.
The password input screen appears.
2 Use the numeric keypad to input the password.
Input the password you registered.
150
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
When the valid password is entered, the frequency display screen appears.
Remark If an invalid password is entered, the transceiver is turned off automatically.
Caution
If you have forgotten the registered password, carrying out all resetting allows you to turn on the
transceiver without entering the password.
It should be noted that performing all resetting resets (initializes) all information such as the information
registered to memory channels and various setting values.
It is recommended that the password be written down on paper.
Setting the PTT Delay Time PTT DELAY Function
Set a timed delay before actual transmission begins after is pressed.
1 Rotate the DIAL, then touch [13 PTT DELAY].
2 Rotate the DIAL to select the desired setting.
OFF/20ms/50ms/100ms/200ms
Selecting OFF disables the PTT delay time function.
Remark The default setting: OFF
Setting the ARS Function
RPT ARS Function
Enable or disable the automatic Repeater Shift operation ARS (Repeater operation is
initiated by tuning to the repeater frequency).
1 Rotate the DIAL, then touch [14 RPT ARS].
2 Rotate the DIAL to select the desired setting.
ON Enables the ARS function.
OFF Disables the ARS function.
Remark The default setting: ON
Setting the Repeater Shift Direction
RPT SHIFT Function
Set the TX frequency shift direction for repeater use.
1 Rotate the DIAL, then touch [15 RPT SHIFT].
2 Rotate the DIAL to select the desired setting.
SIMPLEX No TX frequency offset.
-RPT Shifts TX to a lower frequency.
+RPT Shifts TX to a higher frequency.
Remark The default setting differs depending frequency
151
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Setting the frequency offset for Repeater Shift
RPT SHIFT FREQ Function
Set the repeater shift offset frequency.
1 Rotate the DIAL, then touch [16 RPT SHIFT FREQ].
2 Rotate the DIAL to select the desired shift offset.
The offset frequency can be set in steps of 0.05 MHz between 0.000 MHz and 150.000
MHz.
Remark The default setting differs depending frequency
Disabling Receiver While No Signal Is Received
Receiver Battery Save Function
Sets the Receive OFF Battery save interval (sleep ratio) to reduce power consumption.
1 Rotate the DIAL, then touch [17 SAVE RX].
2 Rotate the DIAL to select the desired setting (the time interval for disabling the receiver
operation).
0.2 sec (1:1) to 1.0 sec (1:5) In steps of 0.1 second
to 1.0 sec (1:5) to 10 sec (1:50) In steps of 0.5 second
to 1.0 sec (1:50) to 60 sec (1:300 sec) In steps of 5 second
OFF
Selecting OFF disables this function.
Remark The default setting: 0.2 sec (1:1)
Changing the Frequency Step Manually
Rotate the DIAL to select [18 STEP] to set each frequency step, when the Dial Knob is
turned manually.
For details, see “Setting the Frequency Step” on page 47.
Setting Clock Time
Rotate the DIAL to select [19 DATE & TIME ADJ] to set the built-in clock time.
For details, see “Setting Clock Time” on page 43.
152
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CONFIG Menu Operations
Limit the time of a continuous transmission (TOT Function)
Set the transceiver to automatically return to receive mode after transmitting continuously
for a certain period of time. The TOT function limits inadvertent transmission of
unnecessary signals, and unwanted battery power consumption (time-out timer function).
1 Rotate the DIAL, then touch [20 TOT].
2 Rotate the DIAL to set the time for the transceiver to automatically return to receive
mode state in steps of 30 seconds.
OFF/30 SEC to 10 MIN
Selecting OFF disables the TOT function.
Remark The default setting: OFF (European version: 3 MIN)
Tips
When the time-out timer function is active, a beep is emitted when a continuous transmission nears
the set time. About 10 seconds later, the transceiver returns to the receive mode.
The TOT setting is retained until “OFF” is selected in step 2 above.
Setting the Frequency Selection Range for Operation in VFO Mode
VFO MODE Function
Sets the frequency tuning range while operating in VFO mode.
1 Rotate the DIAL, then touch [21 VFO MODE].
2 Rotate the DIAL to select the desired tuning range.
ALL Tuning continues to the next band when reaching the end of a band.
BAND Tuning continues to the other end of the current band when reaching
the end of the band.
Remark The default setting: ALL
Notifying a Call From a Remote Station by Vibration
Rotate the DIAL to select [22 VIBRATOR] to set the vibrator which notifies you of a call
from a remote station.
For details, see “Notification of a Call from a Remote Station by Vibration” on page 113.
Swapping the Dial Knob Functions
1
Rotate the DIAL, then touch [23 DIAL KNOB CHANGE].
2 Press the [CHANGE] key.
The VOL and DIAL knob functions are swapped.
Remark The default setting: the upper knob is DIAL.
153
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: APRS Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[APRS] to set the individual items.
After completing the setup, press to exit from Set mode.
For details on setting each item, refer to “FT2DR/DE APRS Instruction Manual” which is
available on Yaesu website.
154
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SD CARD Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[SD CARD] to set the individual items.
After completing the setup, press to exit from Set mode.
Saving/Loading Data to/from microSD Memory Card
Settings information can be saved to a microSD memory card, also the saved information
can be loaded to the transceiver.
1 Rotate the DIAL, then touch [1 BACKUP].
2 Rotate the DIAL to select the operation to be performed.
Write to SD Saves the transceiver setting information to a microSD memory
card.
Read from SD Loads the information to the transceiver from a microSD memory
card.
3 Press the key.
A pop-up window appears on the LCD.
4 Touch [OK].
5 Touch [OK] again.
When [Write to SD] is selected and data writing completes, a beep sounds and
“COMPLETED” appears on the LCD.
When [Read from SD] is selected and data reading completes, a beep sounds, then
the transceiver restarts with the settings read from the microSD memory card applied.
155
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SD CARD Menu Operations
Saving/Loading Memory Channel Information to/from microSD
Memory Card
Memory channel setting information can be saved onto a microSD memory card, or saved
information can be loaded to the transceiver.
1 Rotate the DIAL, then touch [2 MEMORY CH].
2 Rotate the DIAL to select the operation to be performed.
Write to SD
Saves the memory channel information saved on the transceiver
onto a microSD memory card.
Read from SD Loads the information to the transceiver from the microSD memory
card.
3 Press the key.
A pop-up window appears on the LCD.
4 Touch [OK].
5 Touch [OK] again.
When [Write to SD] is selected and data writing completes, a beep sounds and
“COMPLETED” appears on the LCD.
When [Read from SD] is selected and data reading completes, a beep sounds, then
the transceiver restarts with the settings read from the microSD memory card applied.
Saving/Loading GROUP ID Information to/from a microSD Memory
Card
The Group ID setting information can be saved onto a microSD memory card, or saved
information can be loaded to the transceiver.
1 Rotate the DIAL, then touch [3 GROUP ID], then press the key.
2 Rotate the DIAL to select the operation you want to perform.
Write to SD Saves the GROUP ID information saved on your transceiver to a
microSD memory card.
Read from SD Loads the information to your transceiver from a microSD memory
card.
3 Press the key.
Displays a list of the groups registered with the transceiver (or saved on the microSD
memory card).
4 Select the group you want to copy to or from the microSD memory card using the
key.
is displayed for the selected image and is displayed for unselected images.
5 Touch [WRITE] or [READ].
A pop-up window appears on the LCD.
6 Touch [OK].
156
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: SD CARD Menu Operations
7 Touch [OK] again.
When [Write to SD] is selected and data writing completes, a beep sounds and
“COMPLETED” appears on the LCD.
When [Read from SD] is selected and data reading completes, a beep sounds, then
the transceiver restarts with the settings read from the microSD memory card applied.
Formatting a microSD Memory Card
Format a new microSD memory card.
For details, see “Formatting a microSD Memory Card” on page 31.
157
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: OPTION Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[OPTION] for the USB camera setting.
After completing the setup, press to exit from Set mode.
Setting the Optional Microphone With Camera for Use
Image size and quality can be set for the optional microphone with camera (MH-85A11U).
1 Touch [1 USB CAMERA].
2 Rotate the DIAL to select [SIZE], then press the key.
3 Rotate the DIAL to select one of the following image size settings.
160*120 / 320*240
Remark The default setting: 160*120
4 Press the key.
5 Rotate the DIAL to select [QUALITY], then press the key.
6 Rotate the DIAL to select one of the following image quality levels.
LOW / NORMAL / HIGH
Remark The default setting: LOW
7 Rotate the DIAL to select [SP SEL], then press the key.
8 Rotate the DIAL to select the speaker.
CAMERA The audio is routed to MH-85A11U speaker (internal speaker is off).
INT SP The audio is routed to the internal speaker (MH-85A11U speaker is off).
Remark The default setting: CAMERA
Cautions
y If image size is set to large or image quality is set to high, the data transmission time becomes longer.
y The transmission time varies depending on the image size.
158
Customize Menu Settings for Individual Use (Set Mode)
Set Mode: CALLSIGN Menu Operations
Press and hold the key for over one second to display “SETUP MENU”, then touch
[CALLSIGN] for the call sign setting.
1 See “Entering Letters” on page 19 to input the call sign, then press .
After registering the call sign, the transceiver exit from Set mode.
159
Functions to Use as Necessary
Functions to Use as Necessary
Using the Transceiver for Packet Communication
You can perform packet communication with your transceiver by connecting a TNC
(Terminal Node Controller) using an optional Microphone Adapter (CT-44).
TNC
SP
GND
GND
2 kΩ
10 F
ȣ
MIC
MIC
EAR
PTT
TNC
SP
GND
GND
2 kΩ
10 F
ȣ
MIC
MIC
EAR
PTT
After connecting the TNC to the transceiver, set the output signal level to the TNC by
adjusting the sound volume level of your transceiver.
Also, adjust the signal level input to your transceiver using the output level adjustment
volume on the TNC (Input level cannot be adjusted on your transceiver).
Caution
When sending a vast volume of data, the transmission takes a longer time and the transceiver may be
overheated. If the transmission is continued for a long time, the overheat prevention circuit will operate
and the transmission power decreases. If the transmission is continued further, the transmission will be
automatically stopped to prevent the transceiver from overheating and consequently malfunctioning. If
the overheat prevention circuit has operated and then the transceiver returns to the receive mode, turn
the transceiver off, or leave it in the receive mode until the temperature falls.
Tips
Set the receive battery Save Function to OFF during packet communication by selecting [CONFIG]
[17 SAVE RX] in the Set mode.
Reception can be interfered with by noise generated from your PC.
If the transceiver enters an abnormal receive state, disconnect the transceiver from the PC, and
reconnect it to the PC using a photo coupler device or noise filter.
For details on how to connect TNC to the PC, refer to the TNC instruction manual.
160
Functions to Use as Necessary
Clone Operation
Data and various settings saved in your transceiver can be copied to any other FT2DR/
DE transceiver.
DATA
terminal
DATA
terminal
1 Turn off the power of both FT2DR/DE transceivers, then connect an optional clone
cable (CT-168) to the DATA terminal of each transceiver.
2 While pressing and holding the keys on both FT2DR/DE transceivers, press
.
The two transceivers are turned on and placed in the clone mode.
3 Touch [RECEIVE] on the receiving side transceiver and [SEND] on the transmitting
side.
Data copy starts.
When data copy starts, the display on the receiving transceiver changes from “--WAIT-
-” to “--RX--”. On the transmission side transceiver, when data transmission begins,
the transmission data amount indicator appears on the LCD. On the receiving side
transceiver, when data reception starts, the indicator appears on the LCD as well.
Tips When copying is completed, the receiving side transceiver returns to the normal mode. On the
transmission side transceiver, the indication on the LCD returns from “--TX--” to “CLONE”.
4 Turn off the power of both transceivers, then disconnect the clone cable.
Cautions
y When the “ERROR” appears on the LCD during data transfer, copying cannot be completed. Check
the clone cable connection, and redo the operation from the beginning.
y Time data cannot be copied.
161
Functions to Use as Necessary
Connecting an External Device
Connecting to a PC
Exporting position location information received by the FT2DR/DE internal GPS unit
To enable data transfers, connect a Personal Computer to the DATA terminal of the
transceiver with the optional PC connection cable (SCU-19), as described below.
To output location information data from the internal GPS unit, change Set mode
[APRS] [17 COM PORT SETTING] from [OUTPUT] to [GPS]. This enables the
transceiver to transmit your location information to the PC at about one second
intervals. Using this location information, you can display your current location
information on the map software, etc.
Tips For details on setting “17 COM PORT SETTING”, see Set mode in the APRS Instruction
Manual.
To display the location information, software compatible with NMEA-0183 specifications for
GGA and RMC sentence is required.
To use the SCU-19, a dedicated driver must be installed on the PC. To download the dedicated
driver and installation manual, please refer to the YAESU website homepage (http://www.
yaesu.com).
Updating the FT2DR/DE firmware
To update the transceiver firmware, connect your PC to the DATA terminal of the
transceiver with the supplied USB cable, as described below:
When a new firmware update for the FT2DR/DE is available, download the data from
the YAESU website to update the FT2DR/DE to the latest version.
USB Cable (supplied)
or
SCU-19 (option)
162
Functions to Use as Necessary
Connecting an External Device
Connecting to an External Device
The location information data can be exchanged with commercially available GPS
receivers or other external devices by using the optional Data Cable (CT-170).
CT-170 (optional)
Tip
Connect the Data Cable (CT-170) and the Data Output Cable (CT-176) referring to the instruction
manual for the connected device and the following cable specifications.
Connection Cables
Data Cable (CT-170)
RXD (Serial data input [FT2D← External device) RXD (Serial data input [FT2D←External device])
TXD (Serial data output [FT2D→External device) TXD (Serial data output [FT2D→External device])
GND GND
Data Output Cable (CT-176)
RXD (Serial data input [FT2D←External device) TXD (Serial data output [FT2D→External device])
TXD (Serial data output [FT2D→External device) RXD (Serial data input [FT2D←External device])
GND GND
163
Appendix
Appendix
Optional Parts
Speaker / Microphone (MH-34B4B)
Earpiece Microphone (SSM-57A)
VOX Headset (SSM-63A)
Microphone Adapter (CT-44)
DC Cable w/ Noise Filter (SDD-13)
(USA/EXP market only)
DC Cable (E-DC-6) (USA/EXP market only)
BNC-to-SMA Adapter (CN-3)
Soft Case (SHC-24)
3x “AA” Cell Battery Case (FBA-39)
Lithium Ion Battery Packs
(FNB-101LI, 7.4 V, 1,100 mAh)
Lithium Ion Battery Packs
(Equivalent of the supplied accessory)
(SBR-14LI: 7.2 V, 2,200 mAh)
Rapid Charger (CD-41)
Battery Charger
(Equivalent of the supplied accessory)
(PA-48B/C/F/U*)
Battery Charger (SAD-14B; for USA market)
Speaker Microphone with Snapshot camera
(MH-85A11U)
Clone Cable (CT-168)
Data Cable (CT-170)
PC connection cable (SCU-19)
PC connection cable (CT-169)
DataCable(2.5Φ)(CT-176)
Belt Clip (SHB-13)
* “B” suffix is for use with 120 VAC (Type-A plug), “C” suffix is for use with 230-240 VAC (Type-C plug),
“F” suffix is for use with 220 VAC, and “U” suffix is for use with 230 VAC (Type-BF plug).
Availability of accessories may vary. Some accessories are supplied as standard per local requirements,
while others may be unavailable in some regions. Consult your Yaesu Dealer for details regarding these
and any newly-available options. Connection of any accessory not approved by Yaesu, should it cause
damage, may void the Limited Warranty on this apparatus.
164
Appendix
If you suspect malfunction Check the following items before requesting a repair.
The transceiver does not turn on.
Is the battery depleted?
Charge the battery pack after purchase, and when the transceiver has not been used for a long time.
Is the battery pack properly attached?
Refer to “Mounting the battery pack” and securely mount the battery pack.
Is the external power supply properly connected?
When using an external power supply, connect the external power supply adapter with a cigarette
lighter plug (SDD-13) or an external power cable (E-DC-6) to DC input jack.
Is the voltage of the battery pack or the SDD-13 correct?
Be sure that there is a charge left in the battery pack (do not completely discharge). Check that the
output voltage of the SDD-13 is approximately 12V.
There is no sound.
Is the level of squelch (or S meter squelch) set too high?
Press the Monitor Switch and verify that you can hear white noise.
Adjust the level of squelch (or S meter squelch) when receiving a weak signal.
Is the volume low?
Rotate the VOL knob clockwise to increase the volume.
Is the tone squelch or DCS on?
When the tone squelch or DCS is on, the sound is not output until the transceiver receives a signal
containing the same tone frequency or DCS code set.
There is no transmission of radio waves.
Are you pressing the switch properly?
Is the PTT lock on?
Is the Busy TX Block (BCLO function) on?
When the Busy TX Block (BCLO function) is on, transmission cannot be done when receiving a signal
even if
is pressed. Wait until signal being received stops and then press .
Is the transmission frequency on a ham radio band?
Transmission cannot be performed on the AM Radio Broadcast Band/ Short Wave Radio Band/ FM
Radio Broadcast Band/ Air Band/ Information Radio Band.
Is the voltage of the battery pack or external power source correct?
Check the remaining charge on the battery pack.
In addition, using an inadequate power supply where voltage drops during transmission will prevent
the FT2DR/DE from operating at full capability.
The keys or DIAL does not respond.
Is the Key Lock or DIAL Lock on?
165
Appendix
If you suspect malfunction
The battery pack cannot be charged or battery
power depletes immediately after charging.
Is the battery pack being charged with a charger specified by Yaesu?
Charge the battery pack using the accessory battery charger (PA-48B or SAD-14B) or the rapid
charge cradle (CD-41).
When using a external power supply, use the external power supply adapter with a cigarette lighter
plug (SDD-13) or an external power cable (E-DC-6).
Is the battery pack in use exhausted?
If the “Charging Error” appears on the LCD when charging, there is a chance the battery pack is over
discharged. If the error is repetitively displayed after charging the battery pack several times, the
battery pack may have reached its service life be defective. Battery packs are consumables. Please
replace the battery pack with a new one immediately. Battery packs can be charged and reused up to
approximately 300 times.
Depending on the combination for simultaneous reception, there may be internal beats from high
frequencies caused by the internal oscillator. This is not a malfunction. (See the calculation formula below:
“n” is for the arbitrary integer). Depending on the combination for simultaneous reception, there may be
fluctuations in receive sensitivity.
Receive Frequency = 12 MHz × n multiplicative
Receive Frequency = 16 MHz × n multiplicative
Receive Frequency = 15.6 MHz × n multiplicative
Receive Frequency = 4.9152 MHz × n multiplicative
Receive Frequency = 15.6 MHz × n multiplicative
Receive Frequency = 18.432 MHz × n multiplicative
Upper Side (A-Band) Frequency = (Lower Side (B-band) Frequency ± 46.35 MHz) × n multiplicative
Upper Side (A-Band) Frequency = (Lower Side (B-band) Frequency ± 47.25 MHz) × n multiplicative
@ Upper Side (A-band) Mode = NFM
166
Appendix
Index
A
Adjusting the LCD Backlight and Key Button Light
Brightness Level ....................................................................130
Adjusting the LCD Contrast Level .........................................129
Adjusting the Microphone Sensitivity ..................................... 134
AF-DUAL ...............................................................................100
Alphabet Input Screen .............................................................19
AM Radio .................................................................................42
AMS .........................................................................................39
APRS .......................................................................................85
APRS Menu Operations ........................................................153
Assigning Name to Memory Bank ...................................64, 136
Assigning Name to Memory Channel ....................................136
Attaching the Supplied Accessories ........................................20
Attenuator (ATT) Function ...............................................50, 132
Auto Power-Off Function .......................................................145
B
Backtrack Function ..................................................................93
BACKTRACK Screen ..............................................................18
Band Scope Screen.................................................................17
Basic Operation .......................................................................32
Battery Case ............................................................................25
Battery Pack ............................................................................22
Bell Function ..........................................................................114
Busy Channel Lockout (BCLO) Function...............................145
C
CALLSIGN Menu Operations ................................................158
Canceling Memory Channel Registration in Memory Bank .....63
Changing the Display Pattern of the S-Meter ........................131
Changing the Frequency Step Manually ...............................151
Changing the Home Channel Frequency ................................58
Changing the Lighting Condition ...........................................129
Changing the Number of Times the Bell Rings...................... 115
Changing the Opening Message Displayed Immediately
after Power-on .......................................................................130
Clearing Memories ..................................................................59
Clock Time .......................................................................43, 151
Clock Type Function ..............................................................147
Clone Operation ....................................................................160
CONFIG Menu Operations ....................................................145
Connecting to an External Device .........................................162
Connecting to a PC ...............................................................161
Connection Cables ................................................................162
Convenient Functions ..............................................................96
D
Deleting the Frequency Registered to the Skip Search
Memory Channel .....................................................................73
Digital Group Monitor Function ................................................ 83
Displaying the Battery Voltage...............................................130
Displaying the Memory Tag .....................................................61
Displaying the Software Version ............................................ 131
Displaying Your Location in Digital Mode ..............................134
DISPLAY Menu Operations ...................................................128
DTMF Function ......................................................................103
DTMF Memory .......................................................................103
Dual Band Screen ...................................................................17
Dual Receive (DW) Function ...................................................96
DW ...........................................................................................96
E
E-DC-6 .....................................................................................27
External Device .....................................................................161
External Power Supply ......................................................26, 27
F
FBA-39 ....................................................................................25
FM Radio .................................................................................42
Formatting a microSD Memory Card ..................................... 156
Frequency Step .......................................................................47
Function Menu Screen ............................................................17
G
GM ...........................................................................................83
GM Menu Operations ............................................................144
GPS .........................................................................................86
GPS Log Function ...................................................................89
GPS Operation ........................................................................91
GPS Screen Information..........................................................91
H
Home Channel Dual Receive ..................................................98
I
If you suspect malfunction .....................................................164
L
LED Light ...............................................................................148
Loading Data to/from microSD Memory Card .......................154
Loading GROUP ID Information to/from a microSD
Memory Card .........................................................................155
Loading Memory Channel Information to/from microSD
Memory Card .........................................................................155
LOCK Function ......................................................................148
Locking Keys ...........................................................................49
Locking Switches .....................................................................49
M
Manually Transmitting the DTMF Code .................................105
Memory ....................................................................................54
Memory Bank ..........................................................................62
Memory Bank Link Scanning ...................................................79
Memory Channel Dual Receive ............................................... 98
Memory Channel Scanning .....................................................76
MEMORY Menu Operations ..................................................136
Memory Tag ............................................................................. 59
Mode........................................................................................48
Muting Audio ....................................................................44, 135
N
New Pager Function ...................................................... 116, 139
Notification of a Call from a Remote Station by the Bell ........ 138
Number Input Screen ..............................................................19
O
Operating Band .......................................................................34
Optional Microphone With Camera for Use ........................... 157
167
Appendix
Index
Optional Parts ........................................................................163
OPTION Menu Operations ....................................................157
P
Packet Communication..........................................................159
Password Function ................................................................149
Permitting/Prohibiting Transfer of Home Channel
Frequency to VFO .................................................................147
PMS .........................................................................................81
Preset Receiver .......................................................................65
Programmable Memory Channel Scan ...................................81
Prohibiting Registration to a Memory Channel
Memory Channel Protect Function ........................................137
PTT DELAY Function.............................................................150
R
Recalling a Memory Channel ..................................................57
Recalling Memory Bank...........................................................63
Recalling the Home Channels .................................................57
Receiver Battery Save Function ............................................151
Registering to Memory Banks .................................................62
Registering to Memory Channel ..............................................55
Repeater Operation .................................................................52
Reset .......................................................................................51
Resetting the All Set Mode Settings ......................................120
Restoring the Cleared Memories ............................................. 59
RPT ARS Function ................................................................150
RPT SHIFT FREQ Function ..................................................151
RPT SHIFT Function .............................................................150
S
Saving Data to/from microSD Memory Card .........................154
Saving GROUP ID Information to/from a microSD Memory
Card .......................................................................................155
Saving Memory Channel Information to/from microSD
Memory Card .........................................................................155
SCAN Menu Operations ........................................................142
Scanning Function ...................................................................71
Scanning the Memory Bank ....................................................79
SD CARD Menu Operations ..................................................154
SDD-13 ....................................................................................26
SD Memory Card .....................................................................29
Searching for the CTCSS Tone ............................................. 111
Searching for the DCS Code ................................................. 112
Selecting a CTCSS Tone Frequency ..................................... 141
Selecting a DCS Code...........................................................138
Selecting a Frequency Band ...................................................37
Selecting a Receive Operation When Scanning Stops .........143
Selecting the Communication Mode ........................................ 39
Selecting the Display Language ............................................129
Selecting the Squelch Type ...................................................109
Selecting the Vibrator Operation Mode .................................114
Set Mode ...............................................................................119
Set Mode Operation ..............................................................119
Setting a Time Interval for Saving GPS Position
Information.............................................................................147
Setting Memory Bank Link.....................................................136
Setting the Compass Display ................................................128
Setting the DCS Code ...........................................................112
Setting the DTMF Code .........................................................139
Setting the Key Operation Confirmation Sound.....................146
Setting the Memory Channels Used for Registration ............137
Setting the Operation of the Key .....................................148
Setting the Pop-up Time of the Remote Station
Information.............................................................................133
Setting the Receive Operation When Scanning Stops ............74
Setting the Scanning Range ..................................................143
Setting the Search Channels .................................................128
Setting the Squelch Type for the Digital Mode ......................133
Setting the Standby Beep ......................................................134
Setting the Tone Frequency ................................................... 110
Setting the Transmission Method of the DTMF Code............138
Setting the Transmit Modulation Level ..................................132
Setting the Type of Squelch ...................................................141
Setting What to Display Using the Smart Navigation
Function .................................................................................128
SIGNALING Menu Operations ..............................................138
Simultaneous Radio Broadcast Reception ............................135
Skip Search Memory ...............................................................72
Smart Navigation .....................................................................93
S-Meter Squelch Function .....................................................140
Snapshot Function.................................................................107
Specifications ........................................................................168
Specifying Skip/Selected Memory Channels ........................... 77
Spectrum Analyzer ................................................................106
Split Memory............................................................................56
SQL EXPANSION Function ...................................................140
SQL LEVEL Function .............................................................139
Squelch Level ..........................................................................47
Supplied Items ...........................................................................8
Swapping the Dial Knob Functions........................................152
Switching the Receive Mode .................................................133
T
Tables of Set Mode Operations .............................................121
Timer Function .......................................................................149
Tone Calling (1750 Hz) ............................................................53
Tone Search Function............................................................141
Tone Squelch Function ..........................................................109
TOT Function .........................................................................152
Touch Screen.............................................................................7
Transmission Power Level ......................................................46
Transmitting and Receiving a DCS Code with an Inverted
Phase DCS INVERSION Function ........................................138
Transmitting the Registered DTMF Code ..............................104
Transmitting the Saved Image to Other Transceivers ...........108
Tuning to a Frequency .............................................................38
Turning off the BUSY Indicator ..............................................146
TX/RX Menu Operations .......................................................132
V
VFO Dual Receive ...................................................................97
VFO MODE Function.............................................................152
VFO Scan ................................................................................71
Vibration ........................................................................113, 152
Viewing the Saved Image ......................................................108
Volume Level ...........................................................................34
W
Weather Alert Feature ...........................................................141
WIRES-X .................................................................................85
WIRES-X Menu Operations...................................................144
168
Appendix
Specifications
y General
Frequency Range (A): RX: 520 - 1710 kHz, 1.8 - 30 MHz,
30 - 76 MHz (USA version),
30 - 88 MHz (EXP/European version),
76 - 108 MHz (USA version),
88 - 108 MHz (EXP/European version),
108 - 137 MHz, 137 - 174 MHz,
174 - 222 MHz,
222 - 420 MHz,
420 - 774 MHz (USA version),
420 - 800 MHz (EXP/European version),
803 - 999 MHz (Cellular Blocked, USA version),
800 - 999 MHz (EXP/European version)
Frequency Range (B): RX: 108 - 137 MHz, 137 - 174 MHz,
174 - 222 MHz,
222 - 420 MHz, 420 - 470 MHz,
470 - 580 MHz
Frequency Range (A/B): TX: 144 - 146 MHz or 144 - 148 MHz,
430 - 440 MHz or 430 - 450 MHz
Channel Steps: 5, 6.25, 8.33, 9, 10, 12.5, 15, 20, 25, 50, 100 kHz
Mode of Emission: F1D, F2D, F3E, F7W
Frequency Stability: ±2.5ppm(−20°Cto+60°C[−4°Fto+140°F])
Operating Temperature Range:
−20°Cto+60°C(−4°Fto+140°F)
Supply Voltage: Nominal: 7.2 V DC, Negative Ground SBR-14LI,
Nominal: 7.4 V DC, Negative Ground FNB-101LI,
4 - 14 V DC (Negative Ground (EXP DC JACK)),
11 - 16 V DC (Negative Ground (EXP DC JACK with SDD-13))
Current Consumption (Approx.):
RX: 120 mA (Mono Band Receive)
180 mA (Dual Band Receive)
80 mA (Mono Band Receive, Standby)
110 mA (Dual Band Receive, Standby)
50 mA (Mono Band Receive, Standby, Saver On “Save Ratio 1:5”)
50 mA (Dual Band Receive, Standby, Saver On “Save Ratio 1:5”)
+20mA(Digital)
+20mA(GPSOn)
400
μ
A (Auto Power Off)
TX: 1.6 A (5 W TX, 144 MHz 7.2 V DC)
1.8 A (5 W TX, 430 MHz 7.2 V DC)
Case Size (W
× H × D):
62×110×32.5mm(2.4″×4.3″×1.3″)
(with SBR-14LI, w/o knob, antenna & belt clip)
62×110×27mm(2.4″×4.3″×1.1″)
(w/o SBR-14LI, knob, antenna & belt clip)
Weight (Approx.): 310 g (10.93 oz) (with SBR-14LI & Antenna)
169
Appendix
Specifications
y Transmitter
Output Power: 5 W (@ 7.2 V DC or EXT DC)
Modulation Type: F1D, F2D, F3E: Variable Reactance Modulation
F7W: 4 FSK (C4FM)
Spurious Emission: USA/EXP version
At least 60 dB below (@TX Power HI, L3)
At least 50 dB below (@TX Power L2, L1)
European version
At least 60 dB below (@TX Power HI, L3, L2)
At least -36 dBm below (@TX Power L1)
y Receiver
Circuit Type: Double-conversion super heterodyne (NFM / AM)
Direct-conversion (AM / FM Radio)
Intermediate Frequency: 1st: A- Band 47.25 MHz (NFM / AM)
1st: B- Band 46.35 MHz (NFM / AM)
2nd: 450 kHz (NFM / AM)
Sensitivity (for 12dB SINAD):
3
μ
V for 10 dB SN (0.5 - 30 MHz, AM)
0.35
μ
V TYP for 12 dB SINAD (30 - 54 MHz, NFM)
1
μ
V TYP for 12 dB SINAD (54 - 76 (88) MHz, NFM)
1.5
μ
V TYP for 12 dB SINAD (76 (88) - 108 MHz, WFM)
1.5
μ
V TYP for 10 dB SN (108 - 137 MHz, AM)
0.2
μ
V for 12 dB SINAD (137 - 140 MHz, NFM)
0.16
μ
V for 12 dB SINAD (140 - 150 MHz, NFM)
0.2
μ
V for 12 dB SINAD (150 - 174 MHz, NFM)
1
μ
V for 12 dB SINAD (174 - 222 MHz, NFM)
0.5
μ
V for 12 dB SINAD (300 - 350 MHz, NFM)
0.2
μ
V for 12 dB SINAD (350 - 400 MHz, NFM)
0.18
μ
V for 12 dB SINAD (400 - 470 MHz, NFM)
1.5
μ
V for 12 dB SINAD (470 - 540 MHz, NFM)
3
μ
V TYP for 12 dB SINAD (540 - 800 MHz, NFM)
1.5
μ
V TYP for 12 dB SINAD (800 - 999 MHz, NFM, Cellular Blocked)
0.19
μ
V TYP for BER 1% (Digital Mode)
(USA Version Cellular Blocked)
Selectivity (−6dB/−60dB): 12 kHz / 35 kHz (NFM/AM)
AF Output:
700 mW (8 Ω for 10 % THD 7.2 V) internal speaker
300 mW (8 Ω for 10 % THD 7.2 V) external speaker
Specifications are subject to change without notice, and are guaranteed within the 144/222 (USA
version)/430 MHz amateur bands only.
170
Appendix
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
1. Changes or modifications to this device not expressly approved by YAESU MUSEN could void
the user’s authorization to operate this device.
2. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by
the User to operate within the frequency bands allocated to the Domestic public Cellular
Telecommunications Service in Part 22.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio
exempts de licence. Lexploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de lappareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible den compromettre le fonctionnement.
Part 15.21: Changes or modifications to this device not expressly approved by YAESU MUSEN
could void the user’s authorization to operate this device.
DECLARATION BY MANUFACTURER
The Scanner receiver is not a digital scanner and is incapable of being converted or modified to
a digital scanner receiver by any user.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR
RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES
AND FEDERAL LAW.
171
Appendix
Declaration of Conformity
Type of Equipment: 144/430MHz Digital/Analog Transceiver
Brand Name: YAESU
Model Number: FT2DR
Manufacturer: YAESU MUSEN CO., LTD.
Address of Manufacturer: Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa,
Shinagawa-ku,Tokyo 140-0002 Japan
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions; (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The technical documentation as required by the Conformity Assessment procedures is
kept at the following address:
Company: Yaesu U.S.A.
Address: 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
Telephone: (714) 827-7600
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
Electronic and Electric Equipment should be recycled at a facility capable of handling
these items and their waste by products.
In EU countries, please contact your local equipment supplier representative or service
center for information about the waste collection system in your country.
This transceiver works on frequencies which are not gener-
ally permitted.
As for the actual usage, the user has to possess an amateur
radio licence.
Usage is allowed only in the frequency bands which are al-
located for amateur radios.
Attention in case of use
List of national codes
AT BE BG CY CZ DE
DK ES EE FI FR GB
GR HR HU IE IT LT
LU LV MT NL PL PT
RO SK SI SE CH IS
LI NO
172
Appendix
Yaesu UK Ltd
Unit 12, Sun Valley Business Park
Winnall Close
Winchester SO23 OLB
United Kingdom
Tel: +44 (0)1962 866667
Fax: +44 (0)1962 856801
Email: sales@yaesu.co.uk
Declaration of Conformity
Nr. YUK-DOC-0501-15
We, Yaesu UK Ltd. certify and declare under our sole responsibility that the following equipment
complies with the essential requirements of the Directive 1999/5/EC and 2011/65/EU.
Type of Equipment
144/430MHz Digital /Analogue Transcever
Brand Name
YAESU
Model Number
FT2DE
Manufacturer
YAESU MUSEN CO. LTD.
Address of Manufacturer
Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa,
Shinagawa-ku, Tokyo, 140-0002 Japan
Applicable Standards:
This equipment is tested to and conforms to
the essential requirements of directive, as included
in following standards:
Health
1999/5/EC Art. 3 (1) (a)
EN 50566 :2013
Safety
1999/5/EC Art. 3 (1) (a)
EN 60950-1:2006 + A12:2011
EMC
1999/5/EC Art. 3 (1) (b)
EN 301 489-01 V1.9.2
EN 301 489-15 V1.2.1
Radio Spectrum
1999/5/EC Art. 3 (2)
EN 301 783-02 V1.2.1
ROHS2
2011/65/EU Art. 7 (b)
EN 50581:2012
The technical documentation as required by the Conformity Assessment procedures is kept at
the following address:
Company
Yaesu UK Ltd
Address
Unit 12, Sun Valley Business Park, Winnall Close
Technical Construction file
Winchester, Hampshire UK SO23 0LB
Issued by:
Yaesu Musen Co. Ltd, Tokyo Japan
File No:
YETA00389
Drawn up in:
Winchester, Hampshire UK
Date:
08-May 2015
Signed for and on behalf of Yaesu UK Ltd
Name and position: PCJ Bigwood
Technical Sales Manager
Yaesu UK Ltd
Unit 12, Sun Valley Business Park
Winnall Close
Winchester SO23 OLB
United Kingdom
Tel:+44(0)1962866667
Fax:+44(0)1962856801
Email: sales@yaesu.co.uk
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo
140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Copyright 2015
YAESU MUSEN CO., LTD.
All rights reserved.
No portion of this manual
may be reproduced
without the permission of
YAESU MUSEN CO., LTD.
Printed in Japan
1507D-AO
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT2DE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT2DE in de taal/talen: Engels als bijlage per email.

De handleiding is 40,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info