674754
22
Verklein
Vergroot
Pagina terug
1/156
Pagina verder
Page 20 FT DX 9000D OPERATION MANUAL
FRONT PANEL CONTROLS
MOX Switch
Pressing this button engages the PTT (Push to Talk)
circuit, to activate the transmitter. It must be in the
undepressed position for reception. This switch repli-
cates the action of the Push to Talk (PTT) switch on
the microphone. When engaging the MOX switch,
or otherwise causing a transmission to be started, be
certain you have either an antenna or 50-Ohm dummy
load connected to the selected Antenna jack.
VOX Switch
VOX Operation: This button enables automatic voice-
actuated transmitter switching in the SSB, AM, and
FM modes. While activated, the LED inside this but-
ton glows red. The controls affecting VOX operation
are the front panel’s VOX and DELAY knobs
(see section ( ) below. By proper adjustment of these
controls, hands-free voice-actuated operation is pos-
sible.
DIM Switch
Press this button to lower the illumination intensity of
the analog meters, the frequency display, and the TFT.
Press it once more to restore full brightness.
Advice
Menu Items “DISPLAY 014 DIMMER-METER” and
“DISPLAY 015 DIMMER-VFD” allow you to con-
figure the dimming levels for the analog meters and
the frequency display/TFT independently, so you can
customize the brightness levels.
PHONES Jack
A 1/4-inch, 3-contact jack accepts either monaural or
stereo headphones with 2- or 3-contact plugs. When a
plug is inserted, the loudspeaker is disabled. With ste-
reo headphones such as the optional YH-77STA, you
can monitor both Main (VFO-A) and Sub (VFO-B)
receiver channels at the same time during Dual Re-
ceive operation.
Note: When wearing headphones, we recommend that
you turn the AF Gain levels down to their lowest set-
tings before turning power on, to minimize the impact
on your hearing caused by audio “pops” during switch-
on.
POWER Switch
Press and hold in this switch for two seconds to turn
the transceiver on, after first setting the rear panel
Power switch to the “
I
” position. Press and hold in
this switch for two seconds, similarly, to turn the trans-
ceiver off. If the rear panel’s Power switch is set to the
O
” position, the front panel POWER switch will
not function.
Advice
This is the actual power On/Off switch for turning on
the transceiver. When the rear panel’s Power switch is
set to the “
I
” position, power is supplied to the OCXO
to stabilize the reference oscillator, and the remainder
of the transceiver is set in a “stand-by” mode, await-
ing the command for the transceiver to switch on via
the front panel POWER switch. For further infor-
mation on the rear panel Power switch, please see the
discussion on page 36.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-DX9000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-DX9000 in de taal/talen: Engels als bijlage per email.

De handleiding is 25,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info