478504
125
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Page 123FT-950 OPERATING MANUAL
INSTALLATION OF OPTIONAL ACCESSORIES
Setup the FT-950
The optional FC-40 Automatic Antenna Tuner provides automatic tuning of a coaxial line to present nominal 50-ohm
impedance to the FT-950’s ANT jack.
Before operation can begin, you must instruct the FT-950s microprocessor that the FC-40 is being used. This is done using
the Menu Mode:
FC-40 EXTERNAL AUTOMATIC ANTENNA TUNER
(
FOR WIRE ANTENNA
)
[
TUNE
]
Button
[
CLAR/VFO-B
]
Knob
[
MENU
]
Button
[
SELECT
]
Knob
1. Press the
[
MENU
]
button momentarily, to engage the
Menu mode.
2. Rotate the
[
SELECT
]
knob to select the Menu Item
110 TGEN EXT TUN”.
ADVICE:
Press the
[
SELECT
]
knob momentarily to toggle the
Menu item display between “110 TGEN” and “EXT
TUN”.
3. Rotate the
[
CLAR/VFO-B
]
knob to select “Etu (Ex-
ternal Tuner)”.
4. Press and hold in the
[
MENU
]
button for one second
to save the new setting and exit to normal operation.
Operation
1. Press the
[
TUNE
]
button briefly to activate the Auto-
matic Antenna Tuner.
2. The “ ” icon will appear in the display.
3. If the transceiver frequency is out of the amateur band,
the “ ” icon will not appear.
4. Press and hold the
[
TUNE
]
button for one second to
begin automatic tuning. The transmitter will be en-
gaged, and the “ ” icon will blink while tuning
is in progress.
5. Tuning will stop automatically when a low SWR is
achieved. You may Press and hold the
[
TUNE
]
button
for one second while tuning is in progress, to cancel
the automatic tuning.
6. To disable the Automatic Antenna Tuner, press the
[
TUNE
]
button briefly again.
NOTE:
Please connect a good earth ground to the GND termi-
nal of FC-40.
The carrier signal transmits continuously while tuning
is in progress. Please monitor the operating frequency
before beginning the tuning process. Be sure you are
not interfering with others who may already be using
the frequency.
It is normal to hear the sound of the relays while tun-
ing is in progress.
If the impedance cannot be matched by the FC-40 bet-
ter than 2:1, and the “ ” icon blinks, the micro-
processor will not retain the tuning data for that fre-
quency, as the FC-40 presumes that you will want to
adjust or repair your antenna system to correct the high
SWR condition.
125

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Yaesu-FT-950

Zoeken resetten

  • Ft950 wil niet zenden met jtdx in ft8 ontvangt wel goed settings staan volgens Manuel ingesel, e weet raad? 73 PD4 PG Gesteld op 22-7-2024 om 22:04

    Reageer op deze vraag Misbruik melden
  • Bij het opstarten knippert TX. Ontvangst doet het, maar zenden niet. Wie heeft een oplossing? Gesteld op 15-4-2024 om 14:09

    Reageer op deze vraag Misbruik melden
  • Hoe sluit ik een digibox (MMSTV) aan op een FT950? Gebruikte voorheen een FT575GX2 . Deze had 3 tulpstekkertjes. Audio in audio uit en PTT ontvangst werkt goed en de zender schakelt ook in. Audio signaal klinkt niet zoals het hoort. Gesteld op 28-7-2023 om 19:00

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-950 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-950 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info