674725
18
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
18
FT-70DR/DE Advance Manual
Scanning Only the Specified Memory Channels
1. Recall the memory channel registered as a specified memory channel.
2. Press the
[
F
]
key, then press the
[
2
]
(SCAN) key to start scanning.
Only the memory channels registered as the specified memory channels are
scanned.
Unless two or more specified memory channels are registered, the specified memory channel
scanning does not function.
Programmable Memory Channel Scan (PMS)
Registering to the Programmable Memory Channels
50 sets of PMS memory channels (L1/U1 to L50/U50) are available.
Register the lower and upper frequencies of the frequency range in a pair of Program-
mable Memory Channels,
L
££
: Lower limit memory channel
U
££
: Upper limit memory channel
For more details on registering frequencies to the memory channel, see “Registering To
Memory channel” (see the operating manual).
z
Make sure to use the corresponding numbers for the lower and upper limit memory channels.
z
Set the PMS memory channel for performing the Programmable Memory scanning (PMS) as
follows.
The scan width of the upper and lower limit frequencies must be 100 kHz or more.
The lower and upper limit memory channels must be within the same frequency band.
The lower and upper limit memory channels must not register the lower and upper
channels in reverse.
The PMS memory channel must not register a skip memory channel.
Performing Programmable Memory Channel Scan
The programmable memory channel scan allows scanning a specified frequency range
within the same frequency band.
1. Recall the PMS memory channel to which the lower limit (L
££
)
or upper limit (U
££
)
of the frequency is registered.
2. Press the
[
F
]
key, then press the
[
2
]
(SCAN) key.
Programmable memory channel scanning starts.
During scanning, “P
££
” appears on the upper left side of the LCD.
If the DIAL knob is rotated while scanning is in progress, the scanning will contin-
ue up or down in frequency according to the direction of the DIAL Knob rotation.
If the scanner halts on an incoming signal, the back light will turn ON and the dec-
imal point between the “MHz” and “kHz” digits of the frequency display will blink.
Scanning will resume in about five seconds.
3. Press the PTT switch to cancel the scanning.
z
If the scan has paused on a signal, rotating the DIAL knob will cause scanning to resume
instantly.
z
During scanning, the frequency may be changed only within the programmed frequency
range.
z
During scanning, press the
[
V/M
]
key to return to the normal memory mode.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-70DE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-70DE in de taal/talen: Engels als bijlage per email.

De handleiding is 6,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Yaesu FT-70DE

Yaesu FT-70DE Gebruiksaanwijzing - Deutsch - 44 pagina's

Yaesu FT-70DE Aanvulling / aanpassing - Deutsch - 47 pagina's

Yaesu FT-70DE Gebruiksaanwijzing - English - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info